MAXAR50
This radio is not software programmable. The PL tone can be changed as per the instructons on the manual.
The pinout of the mic connector is:
1------Spkr hi 2------PTT 3------mic audio 4------gnd 5------mic gnd 6------PL disable (shorted to gnd enables PL)
HT440/HT90
The HT-440 is nothing more than an HT-90 in a fancy case. It is strictly a crystal type radio and therefore not programmable (even the PL or DPL boards take physical "reeds"). It is, however, a good radio and will generally exceed rated wattage by about 40%. They will go pretty far out of band just by putting in the right xtals + realigning.
Being a rock radio, 1 pair of crystals (Rx and Tx) are needed for each channel. The radio is fitted with either a 2 pole c/o switch for the 2 ch. model or a 4 pole 4 pos. rotary for the 4 ch. version. It is to all intents and purposes an HT 90 radio ( same circuit board) but a darker coloured case. The same batteries fit but look odd because of the different colours. This radio exhibited very few vices in service, the 2nd local osc. crystal would give up occasionally and the P.L. element would fall out of its socket on the piggyback tone board. The on/off switch contacts can go high resistance causing some funny symptoms but usually a quick burnish with a relay contact or automotive type points file would sort them out. The battery contacts between the case and the circuit board need to be kept clean ( they are tightened by the two screws through the top plate ).
You can find the pinout of the microphone connector here.
Below is the pinout information of a HT90 speaker microphone:
Universal connector, 4-Contact female #0905184J01
Pin 3 Black wire Ground Pin 2 Blue wire Spk Audio from audio pwr amp thru the J202 ext spk jack Pin 5 Gray wire Spk Audio to J401/LS401 Internal Speaker Pin 4 Blue/White wire For External PTT Switch (ground to key) Pin 1 White Wire External Microphone Audio input.
Pins 2 and 5 make up a N.C. switch that opens when a male connector is inserted, disconnecting the internal spkr.
The manual part numbers are as follows:
The UHF Models come in 2 bandsplits, 403-430 MHz and 440-512 MHz. A model chart for this series should look something like:
| H | 2 | 4 | HMB | 1 | 124A |
| H Handheld | 2 1W | 3 VHF | HMB Model Series | 1 Carrier Sq. | 124A Same for all |
| 3 4W UHF | 4 UHF | HMU | 3 Tone PL | ||
| 3 5W VHF | 6 Digital PL |
Motorola made what they called a "Handie-Talkie RF Link". One model number was K24LCF1103BP.
It is a metal gasketed box, that contains a small Celwave duplexer, two HT440's, a power supply and a controller, 1 per radio.
It appears it was available in both VHF and UHF. The second and third digits of the model number determine bandsplit and power level, as follows:
The UHF models were available in either 403-480MHz or 440-512MHz. They are crystal controlled.
The jumper configuration of the interface board is as follows:
| Function | JU1 | JU2 | JU3 | JU4 | JU5 |
| Low Impedence Line Level Output | IN | ||||
| High Impedence Line Level Output | OUT | ||||
| PTT Low to Key | IN | OUT | |||
| PTT High to Key | OUT | IN | |||
| Unsqu. Ind. High with Carrier | IN | OUT | |||
| Unsqu. Ind. Low with Carrier | OUT | IN |
The factory defaults are: High Impedence Line Level Output, Low to Key, and Unsquelched Indicator High with Carrier.
You can see a schematic of the interface board by looking here.
The schematic for the function board containing the power supply and other circuits can be found here.
The manual part numbers are:
MOXY
The pinout of the power connector is below, a picture can be found here.
A------12v + B------gnd (12v -) 1------hang up box 2------hang up box gnd 3------horn out (for horn blower decoder) 4------N/C 5------mic hi 6------N/C 7------switched A+ 8------PTT 9------int Spkr 10-----meter point 1 11-----meter point 5 12-----RX audio 13-----meter point 2 14-----meter point 3 15-----meter point 7
The meter points are for an adapter cable to use with a Motorola test set.
MAXAR/MOXY 6M Conversion
We've been told that there is a book available for putting the low band Moxy or Maxar onto 6 Meters.� It is by William I. Oglivie (VE7MIT) and is available from Zen-In Design, P.O. Box 390700, Mountain View, Ca.� 94039.�
MT500
If you need channel elements for these radios, check out this site http://users.leading.net/~radiotr/MT500.
For further extensive coverage of this model, you should check out MT500.COM.
MX300 Series
Again, most of these are non-synthesized radios (use crystals).
The pinout of the microphone connector can be found here.
HT220
For all the information you could ever want on the HT220, check out http://www.batnet.com/mfwright/HT220.html.
