BUX CommCo Electronic Parts and Components, Page 3

Most components shown on this page are employed in many amateur (HAM) radio applications and interfaces.
The most popular of these interfaces are similar in design and operation.
They are: HF digital modes such as PSK31, SSTV (analog), RTTY, CW and Packet.

We Accept

CLICK HERE for SECURE, online order form

AMPLIFIED   SPEAKER
Special Purchase, Top Quality, Brand Name !

It's a long awaited addition to the HAM shack or the "hand-held" mobile operator. This amplified speaker delivers 8 watts of audio. I use them in my work-stations as audio signal tracers. Hook-up is simple; Connect the Orange wire (with 2 amp fuse holder already inline) to 12 volts DC. Black lead to ground. The other pair of wires go to low level audio (150 to 200 mV). Complete with a durable mounting bracket, and hardware, a red Power-ON LED indicator and volume control. Size is approximately 6"w X 4"h
New, in original carton.

Price = $12.00
Order # AMPSPKR

Price = $7.00
Order # 7-26P

Price = $8.00
Order # 7-26P

Four (4) inch, 10 Watts Power, 8 ohm impedance, with Noise-Canceling switch. 10 ft. cord with 3.5mm (1/8") plug. Mounting hardware is included.

price = $9.00
Order # 7-12

ALINCO, ADI, Icom, Standard, Yeasu, and others
$19.00
Order # DM-630

The ideal replacement 600 ohm MIC with cable and 4 pin mic connector installed.
Black, replacement microphone.

$8.00 or 2/$14.00
Order # DM507

A Hi-Performance, Power Microphone to add punch to your audio, ready for easy installation. MIC uses standard AA 1.5 volt battery.

Wire lead identification:
RED = Audio Out
WHITE = TRANSMIT (PTT)
BLUE = RECEIVE
BLACK = COMMON
SHIELD = GROUND

BUX price = $15.00
Order Model PT-433

Single Pole, Double Throw, switch.

$1.00 each
Order # SPDT2P

Eight switch, "DIP" Eight switches in a row... 8 switch Dual Inline Package.

$1.00 each
Order # DIP8SW

This Push-ON, and Push again for OFF, Double Pole, Double Throw Switch is sometimes used as a ''manual'' means of switching between PSK31 transmit and receive.

$1.00 each
Order # DPDTPOPO

These Push-ON, and Push again for OFF, Double Pole, Double Throw mini-switches provide an ideal way to manually switch between PSK31 transmit and receive, or between microphone and SSTV I/O.

$1.00 each, or 6 for $5.00
Order # POPOMINI

This is the same type, 16 position HEXidecimal switch I use as a channel selector on the 16 and 32 channel RANGR and DELTA radio mods. Arrow-point slot enables channel selection using a small screw driver. Switch detent positions are labeled 0 through 9 and A through F, for a total of 16 positions. The truth table is ''REAL'' not ''Complimentary.''

Price each $2.00
Order number = SW516

Small, 5 to 9 volt DC, DPDT ''CLARE'' sealed relay with .5 amp contacts.
(Can be fitted into 16 pin DIP socket, not supplied).

Price Each $2.50
Order number = RL2410

Chrome, spring, Mic Hanger.

2 for $1.00
Order # MHANGR

2.5mm ID DC barrel type connector on one end, with cigarette lighter plug at the opposite end.

Order # 25-CIGDC
BUX CommCo price = $3.00 each

LabTec C-324 Stereo headphone with boom microphone. 8' shielded cord with 3.5mm gold stereo plug for headset and 3.5mm gold plug for microphone. Adjustable double headband and microphone arm for easy positioning.

$18.00 each
Order # LTC324

10K pot with On/Off switch.
Shaft is 1/4".
Comes complete with knob and mounting hardware.

$1.00,      ORDER No.   10KWKNOB

This blue background section contains; Cables, Connectors, Components, and Cases that are used to build PSK31 and SSTV interfaces.

This is a high quality, 9 conductor curly cord with DB9 female connector attached. It extends more than 6 feet. Two of the wires are shielded.

$3.00     ORDER No. CURLYDB9

600 ohm to 600 ohm, 1:1 turns ratio audio coupling transformer.

Used in most PSK31 transceiver to sound-card interfaces to isolate the sound card and HF transceiver from RF feedback. Use two of these to isolate both the sound card LINE IN and LINE OUT from the transceiver accessory or data port. Primary is identified on transformer. Transformer measures approximately one half inch by one half inch. Leads are 1/2 inch long.

$3.00 each or 2/$5.00
Order # XFMR6K6

1000 (1k) ohm to 8 ohm, audio transformer.

Used in PSK31 transceiver to sound-card interfaces to isolate the sound card and HF transceiver from RF feedback. This 1K to 8 ohm transformer is used when external speaker audio is coupled to the sound card LINE IN. Primary (1000 ohm) and secondary (8 ohm) are identified on transformer. Transformer measures approximately one half inch by one half inch. Leads are 1/2 inch long.

$3.00 each or 2/$5.00
Order # XFMR1K8

The audio transformers shown at left, have center-taps on both the primary and secondary windings. The center-tap may be used, or left open (user option).

Used in PSK31 transceiver to sound-card interface, this shielded, twin cable has two, 3.5mm stereo connectors on one end. When using with PSK31, SSTV, RTTY, and Packet Sound card interfaces, only the "tip" of each connector is used; The "ring" is not used. NOTE that a large ferrite core is molded into the line near the sound card end of the cable. This is another means of preventing noise and RF feedback between the transceiver and the PC sound card. Twin cable is 48 inches (4 ft) long.
$3.50 each
Order # SCABLE-48

6 ft shielded DB9 female, pins 1 and 9 are not connected.
1=n/c
2 = BLACK
3 = Brown
4 = RED (DTR)
5 = BARE (GROUND)
6 = YELLOW
7 = GREEN (RTS)
8 = BLUE
9 = n/c

$1.50 each, Order # DB9S

10 K pot for audio level control in
PSK31 and SSTV interface circuits
where transceiver (input & output)
jack(s) to sound-card I/O is required.

$0.75 each or 2/$1.00
Order # H-POT-10K

This PCB is the same PCB I use to construct my PSK31 and SSTV sound card interface circuits on.
The ISO kits are used to interface your transceiver and PC SB-16 sound card for use with PSK31 and SSTV.

$3.00 each or 2/$5.00
Order # ISO-PCB

3-1/4" x 3" x 1" project enclosure. This project box/enclosure provides ample space for small projects. The box uses ''friction-fit'' action to keep the completed project securely closed. Once pressed together, the box assumes a tight enclosure. Works great for the ISO-KIT PSK31 interfaces and other related projects.

$2.00 each or 4/$7.00
Order # BLUEBOX

This case is made of durable plastic and is the same enclosure I use to house my personal PSK31 and SSTV ISO-KIT interface projects. When completed, the 2" x 2" circuit board, PSK31 interface fits easily into this project box. All sides and surfaces are smooth and the ''Live-Hinge'' lid has an easy open internal snap-lock. The snap-lock allows easy access to set internal pots and/or controls. Made In the USA, exclusively for
BUX CommCo
$1.50 each or 4/$5.00
Order # BUX BLACK BOX

For a complete PSK31/RTTY/SSTV
Sound Card to Transceiver wired and Tested interface, CLICK HERE!

6.8 uF, 35 vdc Tantalytic capacitors with wire leads cut for PC board mounting.
Popular as PSK31 and SSTV interface coupling caps.
Price Each $0.50 or 3/$1.00
Order number = C68-35

Red LED    4/$1.00
Order number = REDLED

1N914 / 1N4148 Diode. The popular switching diode used in many universal interface applications.

Price 10/$1.00
Order no. 1N4148

OCTAL "D-type"
LATCH. CMOS
IC comes with 20 pin IC socket as shown. 74HC373

$1.00     ORDER No. 74HC373

Electret Condenser Microphone Element.
Replaces many mic elements used in HAM and Commercial 2-way Radio equipment.

$4.00 each     ORDER No. ELECMIC

UM-9401/MA-47266 PIN Diode, used in VHF & UHF transceiver Tx/Rx switching circuits.

$1.00 Each       Order No. 9401

This transistor is used in hundreds of HAM Radio projects and applications, including some PSK31 circuits to activate transceiver PTT.

$0.50 each or 12/$5.00
Order # 2N2222

This 2N3053 will add buffer strength to the PTT circuit to handle heavy T/R relay current loads.                 --->
The circuit RIGHT of this photo is an example of how the 2N3053/ 5033 is incorporated into the PTT circuit. The same PTT feature can be applied in SSTV/sound card interfacing.

$.75 each or 5/$3.00
Order # 2N3053

2N3904 NPN Transistor with short, formed leads for Printed Circuit Board installation.

$0.50 each or 3/$1.00
Order # 2N3904S

This transistor is used in some PSK31 circuits to activate transceiver PTT. Control of the PTT action is via software. The same PTT feature is activated in SSTV/sound card software.

$0.35 each or 4/$1.00
Order # MP2222

This transistor is used in many 12 Volt DC power supplies that are used in Amateur Radio stations. 12 VDC supplies that are rated at 3 to 7 amperes usually use only one. Supplies that are rated at 10 to 20 amperes usually use two. Power supplies that are 25 to 30 amperes usually have four of these power regulator transistors attached to a large heat-sink.

$1.00 each or 6/$5.00
Order # 2N3055

The 2N7000 MosFET N Channel transistor is often used in many SSTV and PSK31 interface applications.

$ .80 each or 5/$3.00
Order # 2N7000

18 Volt Zener Diode used in the MFJ-1270B/C (CR-1) and MFJ-1278 as the protection diode. Keep several on hand when storm season arrives.

Price Each $0.50 or 3/$1.00
Order # 1N4746Z

Hundreds of applications, including
audio level control in PSK31 and SSTV interface circuits where transceiver I/O
ports to sound-card I/O is required.
Pot appearance may be different form photo shown, pin spacing is the same.

$0.75 each or 2/$1.00

1000 ohm, Order # H-POT-1K
5000 ohm, Order # H-POT-5K
10,000 ohm, Order # H-POT-10K
25,000 ohm, Order # H-POT-25K
47,000 ohm, Order # H-POT-50K

10K pots, mount using two screws, each side.
1/4 inch nylon shaft.
2/$1.00 10KNY2 10K pots, uses two bend-flap for mounting. 1/4 inch
half-moon shaft.
2/$1.00 10KHM2
10K pot with On/Off switch. Shaft is 1/4". Comes complete with knob and mounting hardware.

$1.00,      ORDER No.   10KWKNOB

This 4N33 Darlington optocoupler is used all RASCAL PSK31 and SSTV interfaces.
The 4N33 is used to isolate PSK31 and SSTV sound card from the transceiver PTT circuits to reduce RF feedback.

$1.00 each 4/$3.00
(includes IC socket with each IC)
Order # 4N33

Order Optoisolator(s) by number.

4N25
4N29
4N32
4N33
4N35
4N37
HA11-V2A
IL-5
IL-30

$1.00 each 4/$3.00
(6 pin IC socket included with each IC)

6 pin IC socket
0.25 each or 5/$1.00
Order No. 6PDIP

TDA2002/3 Audio Amp IC

Price Each $1.50
Order number = TDA2K2

LM341T / 78M15T 15 Volt @ 3 amp regulator (TO-220 case). Requires heat sink.

Price Each $1.50
Order number = TR710

Over 250 MegaBytes of HAM radio Diagrams, Documents, Radio & TNC Modifications, and Antenna articles. Many articles from my Packet Users Notebook column in CQ magazine. A storehouse of information for every HAM and Hobbyist.

$14.00 Order number = 2K1CD

The popular 27C512 EPROM used to program (burn) as an X1J4 TheNET IC. Used in the MFJ-1270B/C and PacComm Tiny 2 and Tiny 2 MKII at U23. Erase, and program over 1000 times.

Price Each $4.50
Order number = EP-27C512

Small, 1.2 uH RF Choke 3/8" long with axial leads.

Price Each $0.25 or 5/$1.00
Order no. RF815

1.86 uh RF Choke 1.0" long with axial leads.

$0.50 or 3/$1.00
Order number = RFC68

This 470 uFd, 16 volt filter is one half inch diameter, 7/8 inch tall, with radial leads. It is useful as filter for that 5 to 12 volt DC supply output, or as low frequency by-passing on the DC lead, final filtering.

Price Each $0.25 or 5/$1.00
Order number = C47016

Special applications ''NON-Polarized'' 2.2 ufd caps used primarily as audio coupling capacitor in the receive and transmit (audio) AFSK lines between the TNC and radio. A must when modifying radios for 9600 bauds..

Price Each $0.50 or 3/$1.00
Order number = C2.2NP

Increase coupling, crank more 9k6 data with these 4.7 ufd capacitors. They are ''NON-polarized'' and are used in the transmit and receive audio lines in many commercial radio modifications for 9600 bauds and TNC to radio audio I/O paths.

Price Each $0.50 or 3/$1.00
Order number = C4.7NP

These two connectors are identical, 8 pin plug and jack. This is a good utility connector for many application.
I use a pair as disconnect headers for my HAM-M Rotor during lightning storms.

Price 2 per pack @ $1.00
Order number = CN0808

Drilled the hole in the wrong place? Removed an old base-loaded 3/8 inch hole mount antenna; This black rubber plug is inserted into the hole to seal from moisture. It can be painted to blend color. The profile is about 1/8 inch high when inserted, and 1-1/2 inch in diameter.
Price Each $1.00
Order number   K-37

Four (4) inch Nylon Ty-Wraps. Hundreds of uses; Handy for cable ties and arranging those cables hanging from of the PC.

Price per pack of 100, = $1.00
Order number = TYW100

Flat 1/4" wide LEDs, 2 Red, and 2 Green;
$1.00    Order No. 4RG-LED

Complete PSK31/RTTY/SSTV
Sound Card to Transceiver interfaces and info, CLICK HERE!

3.5mm Stereo jack. Although made for PC board mounting, they may also be used to make "in-line" jacks for sound-card applications.
$2/$1.00     Order No. 35SPCBJAK

We Accept

CLICK HERE for SECURE, online order form

If FAX, provide all information from order form to:
FAX    434 525 7818

Back to BUX CommCo Antenna, Accessories, and Components, Home Page.

AMPLIFIED SPEAKER Special Purchase, Top Quality, Brand Name ! It's a long awaited addition to the HAM shack or the "hand-held" mobile operator. This amplified speaker delivers 8 watts of audio. I use them in my work-stations as audio signal tracers. Hook-up is simple; Connect the Orange wire (with 2 amp fuse holder already inline) to 12 volts DC. Black lead to ground. The other pair of wires go to low level audio (150 to 200 mV). Complete with a durable mounting bracket, and hardware, a red Power-ON LED indicator and volume control. Size is approximately 6"w X 4"h New, in original carton. Price = $12.00 Order # AMPSPKR
Price = $7.00 Order # 7-26P	Price = $8.00 Order # 7-26P	Four (4) inch, 10 Watts Power, 8 ohm impedance, with Noise-Canceling switch. 10 ft. cord with 3.5mm (1/8") plug. Mounting hardware is included. price = $9.00 Order # 7-12
ALINCO, ADI, Icom, Standard, Yeasu, and others $19.00 Order # DM-630	The ideal replacement 600 ohm MIC with cable and 4 pin mic connector installed. Black, replacement microphone. $8.00 or 2/$14.00 Order # DM507	A Hi-Performance, Power Microphone to add punch to your audio, ready for easy installation. MIC uses standard AA 1.5 volt battery. Wire lead identification: RED = Audio Out WHITE = TRANSMIT (PTT) BLUE = RECEIVE BLACK = COMMON SHIELD = GROUND BUX price = $15.00 Order Model PT-433

*Single Pole, Double Throw*, switch. $1.00 each Order # SPDT2P	Eight switch, "DIP" Eight switches in a row... 8 switch Dual Inline Package. $1.00 each Order # DIP8SW	This Push-ON, and Push again for OFF, Double Pole, Double Throw Switch is sometimes used as a ''manual'' means of switching between PSK31 transmit and receive. $1.00 each Order # DPDTPOPO
These Push-ON, and Push again for OFF, Double Pole, Double Throw mini-switches provide an ideal way to manually switch between PSK31 transmit and receive, or between microphone and SSTV I/O. $1.00 each, or 6 for $5.00 Order # POPOMINI	This is the same type, 16 position HEXidecimal switch I use as a channel selector on the 16 and 32 channel RANGR and DELTA radio mods. Arrow-point slot enables channel selection using a small screw driver. Switch detent positions are labeled 0 through 9 and A through F, for a total of 16 positions. The truth table is ''REAL'' not ''Complimentary.'' Price each $2.00 Order number = SW516	Small, 5 to 9 volt DC, DPDT ''CLARE'' sealed relay with .5 amp contacts. (Can be fitted into 16 pin DIP socket, not supplied). Price Each $2.50 Order number = RL2410
Chrome, spring, Mic Hanger. 2 for $1.00 Order # MHANGR	2.5mm ID DC barrel type connector on one end, with cigarette lighter plug at the opposite end. Order # 25-CIGDC BUX CommCo price = $3.00 each	LabTec C-324 Stereo headphone with boom microphone. 8' shielded cord with 3.5mm gold stereo plug for headset and 3.5mm gold plug for microphone. Adjustable double headband and microphone arm for easy positioning. $18.00 each Order # LTC324
10K pot with On/Off switch. Shaft is 1/4". Comes complete with knob and mounting hardware. $1.00, ORDER No. 10KWKNOB	This blue background section contains; Cables, Connectors, Components, and Cases that are used to build PSK31 and SSTV interfaces.	This is a high quality, 9 conductor curly cord with DB9 female connector attached. It extends more than 6 feet. Two of the wires are shielded. $3.00 ORDER No. CURLYDB9
600 ohm to 600 ohm, 1:1 turns ratio audio coupling transformer. Used in most PSK31 transceiver to sound-card interfaces to isolate the sound card and HF transceiver from RF feedback. Use two of these to isolate both the sound card LINE IN and LINE OUT from the transceiver accessory or data port. Primary is identified on transformer. Transformer measures approximately one half inch by one half inch. Leads are 1/2 inch long. $3.00 each or 2/$5.00 Order # XFMR6K6	1000 (1k) ohm to 8 ohm, audio transformer. Used in PSK31 transceiver to sound-card interfaces to isolate the sound card and HF transceiver from RF feedback. This 1K to 8 ohm transformer is used when external speaker audio is coupled to the sound card LINE IN. Primary (1000 ohm) and secondary (8 ohm) are identified on transformer. Transformer measures approximately one half inch by one half inch. Leads are 1/2 inch long. $3.00 each or 2/$5.00 Order # XFMR1K8	The audio transformers shown at left, have center-taps on both the primary and secondary windings. The center-tap may be used, or left open (user option).
Used in PSK31 transceiver to sound-card interface, this shielded, twin cable has two, 3.5mm stereo connectors on one end. When using with PSK31, SSTV, RTTY, and Packet Sound card interfaces, only the "tip" of each connector is used; The "ring" is not used. NOTE that a large ferrite core is molded into the line near the sound card end of the cable. This is another means of preventing noise and RF feedback between the transceiver and the PC sound card. Twin cable is 48 inches (4 ft) long. $3.50 each Order # SCABLE-48	6 ft shielded DB9 female, pins 1 and 9 are not connected. 1=n/c 2 = BLACK 3 = Brown 4 = RED (DTR) 5 = BARE (GROUND) 6 = YELLOW 7 = GREEN (RTS) 8 = BLUE 9 = n/c $1.50 each, Order # DB9S	10 K pot for audio level control in PSK31 and SSTV interface circuits where transceiver (input & output) jack(s) to sound-card I/O is required. $0.75 each or 2/$1.00 Order # H-POT-10K
This PCB is the same PCB I use to construct my PSK31 and SSTV sound card interface circuits on. The ISO kits are used to interface your transceiver and PC SB-16 sound card for use with PSK31 and SSTV. $3.00 each or 2/$5.00 Order # ISO-PCB	3-1/4" x 3" x 1" project enclosure. This project box/enclosure provides ample space for small projects. The box uses ''friction-fit'' action to keep the completed project securely closed. Once pressed together, the box assumes a tight enclosure. Works great for the ISO-KIT PSK31 interfaces and other related projects. $2.00 each or 4/$7.00 Order # BLUEBOX	This case is made of durable plastic and is the same enclosure I use to house my personal PSK31 and SSTV ISO-KIT interface projects. When completed, the 2" x 2" circuit board, PSK31 interface fits easily into this project box. All sides and surfaces are smooth and the ''Live-Hinge'' lid has an easy open internal snap-lock. The snap-lock allows easy access to set internal pots and/or controls. Made In the USA, exclusively for BUX CommCo $1.50 each or 4/$5.00 Order # BUX BLACK BOX
	For a complete PSK31/RTTY/SSTV Sound Card to Transceiver wired and Tested interface, CLICK HERE!
6.8 uF, 35 vdc Tantalytic capacitors with wire leads cut for PC board mounting. Popular as PSK31 and SSTV interface coupling caps. Price Each $0.50 or 3/$1.00 Order number = C68-35	Red LED 4/$1.00 Order number = REDLED	1N914 / 1N4148 Diode. The popular switching diode used in many universal interface applications. Price 10/$1.00 Order no. 1N4148
OCTAL "D-type" LATCH. CMOS IC comes with 20 pin IC socket as shown. 74HC373 $1.00 ORDER No. 74HC373	Electret Condenser Microphone Element. Replaces many mic elements used in HAM and Commercial 2-way Radio equipment. $4.00 each ORDER No. ELECMIC	UM-9401/MA-47266 PIN Diode, used in VHF & UHF transceiver Tx/Rx switching circuits. $1.00 Each Order No. 9401
This transistor is used in hundreds of HAM Radio projects and applications, including some PSK31 circuits to activate transceiver PTT. $0.50 each or 12/$5.00 Order # 2N2222	This 2N3053 will add buffer strength to the PTT circuit to handle heavy T/R relay current loads. ---> The circuit RIGHT of this photo is an example of how the 2N3053/ 5033 is incorporated into the PTT circuit. The same PTT feature can be applied in SSTV/sound card interfacing. $.75 each or 5/$3.00 Order # 2N3053
2N3904 NPN Transistor with short, formed leads for Printed Circuit Board installation. $0.50 each or 3/$1.00 Order # 2N3904S	This transistor is used in some PSK31 circuits to activate transceiver PTT. Control of the PTT action is via software. The same PTT feature is activated in SSTV/sound card software. $0.35 each or 4/$1.00 Order # MP2222	This transistor is used in many 12 Volt DC power supplies that are used in Amateur Radio stations. 12 VDC supplies that are rated at 3 to 7 amperes usually use only one. Supplies that are rated at 10 to 20 amperes usually use two. Power supplies that are 25 to 30 amperes usually have four of these power regulator transistors attached to a large heat-sink. $1.00 each or 6/$5.00 Order # 2N3055
The 2N7000 MosFET N Channel transistor is often used in many SSTV and PSK31 interface applications. $ .80 each or 5/$3.00 Order # 2N7000	18 Volt Zener Diode used in the MFJ-1270B/C (CR-1) and MFJ-1278 as the protection diode. Keep several on hand when storm season arrives. Price Each $0.50 or 3/$1.00 Order # 1N4746Z	Hundreds of applications, including audio level control in PSK31 and SSTV interface circuits where transceiver I/O ports to sound-card I/O is required. Pot appearance may be different form photo shown, pin spacing is the same. $0.75 each or 2/$1.00 1000 ohm, Order # H-POT-1K 5000 ohm, Order # H-POT-5K 10,000 ohm, Order # H-POT-10K 25,000 ohm, Order # H-POT-25K 47,000 ohm, Order # H-POT-50K
10K pots, mount using two screws, each side. 1/4 inch nylon shaft. 2/$1.00 10KNY2	10K pots, uses two bend-flap for mounting. 1/4 inch half-moon shaft. 2/$1.00 10KHM2	10K pot *with On/Off switch.* Shaft is 1/4". Comes complete with knob and mounting hardware. $1.00, ORDER No. 10KWKNOB
This 4N33 Darlington optocoupler is used all RASCAL PSK31 and SSTV interfaces. The 4N33 is used to isolate PSK31 and SSTV sound card from the transceiver PTT circuits to reduce RF feedback. $1.00 each 4/$3.00 (includes IC socket with each IC) Order # 4N33	Order Optoisolator(s) by number. 4N25 4N29 4N32 4N33 4N35 4N37 HA11-V2A IL-5 IL-30 $1.00 each 4/$3.00 (6 pin IC socket included with each IC)	6 pin IC socket 0.25 each or 5/$1.00 Order No. 6PDIP
TDA2002/3 Audio Amp IC Price Each $1.50 Order number = TDA2K2	LM341T / 78M15T 15 Volt @ 3 amp regulator (TO-220 case). Requires heat sink. Price Each $1.50 Order number = TR710	Over 250 MegaBytes of HAM radio Diagrams, Documents, Radio & TNC Modifications, and Antenna articles. Many articles from my Packet Users Notebook column in CQ magazine. A storehouse of information for every HAM and Hobbyist. $14.00 Order number = 2K1CD
The popular 27C512 EPROM used to program (burn) as an X1J4 TheNET IC. Used in the MFJ-1270B/C and PacComm Tiny 2 and Tiny 2 MKII at U23. Erase, and program over 1000 times. Price Each $4.50 Order number = EP-27C512	Small, 1.2 uH RF Choke 3/8" long with axial leads. Price Each $0.25 or 5/$1.00 Order no. RF815	1.86 uh RF Choke 1.0" long with axial leads. $0.50 or 3/$1.00 Order number = RFC68
This 470 uFd, 16 volt filter is one half inch diameter, 7/8 inch tall, with radial leads. It is useful as filter for that 5 to 12 volt DC supply output, or as low frequency by-passing on the DC lead, final filtering. Price Each $0.25 or 5/$1.00 Order number = C47016	Special applications ''NON-Polarized'' 2.2 ufd caps used primarily as audio coupling capacitor in the receive and transmit (audio) AFSK lines between the TNC and radio. A must when modifying radios for 9600 bauds.. Price Each $0.50 or 3/$1.00 Order number = C2.2NP	Increase coupling, crank more 9k6 data with these 4.7 ufd capacitors. They are ''NON-polarized'' and are used in the transmit and receive audio lines in many commercial radio modifications for 9600 bauds and TNC to radio audio I/O paths. Price Each $0.50 or 3/$1.00 Order number = C4.7NP
These two connectors are identical, 8 pin plug and jack. This is a good utility connector for many application. I use a pair as disconnect headers for my HAM-M Rotor during lightning storms. Price 2 per pack @ $1.00 Order number = CN0808	Drilled the hole in the wrong place? Removed an old base-loaded 3/8 inch hole mount antenna; This black rubber plug is inserted into the hole to seal from moisture. It can be painted to blend color. The profile is about 1/8 inch high when inserted, and 1-1/2 inch in diameter. Price Each $1.00 Order number K-37	Four (4) inch Nylon Ty-Wraps. Hundreds of uses; Handy for cable ties and arranging those cables hanging from of the PC. Price per pack of 100, = $1.00 Order number = TYW100
Flat 1/4" wide LEDs, 2 Red, and 2 Green; $1.00 Order No. 4RG-LED	Complete PSK31/RTTY/SSTV Sound Card to Transceiver interfaces and info, CLICK HERE!	3.5mm Stereo jack. Although made for PC board mounting, they may also be used to make "in-line" jacks for sound-card applications. $2/$1.00 Order No. 35SPCBJAK