SWR & WATT METER
This is a handy,
compact meter designed for the amateur radio operator to monitor
transmitter operation. May also be used as a RF field strength
meter.
SPECIFICATIONS
|
SWR:
RF- Power
Accuracy
Impedance
Frequency Range
Indicator
Antenna
Dimensions |
1:1 to 1:3
0-10 watts and 0-100watts
SWR 5% RF-Power 10%
52 ohms
1.7MHz to 150 MHz
200 DC Micro-ammeter
5 inches antenna
6" X 2" X 2" |
|
SWR-3
|
$18.00
|
|
Want to make that (4, 6,
or) 8 pin mic
extension? . . now you can, with this in-line, male microphone
connector.
Same gender as the 4, 6, and 8 pin male connectors on most HAM
transceivers, except, this one is an in-line connector. The
CE-8 is shown here, and can be ordered in three versions:
8 pin=C8E, 6 pin= C6E, and 4 pin=C4E.
Use to make microphone extension cables.
| 8 pin, Order No. C8E |
$3.00
|
| 6 pin, Order No. C6E |
$3.00 |
| 4 pin, Order No. C4E |
$3.00 |
|
2.5mm Mono Plug |
2.5mm Stereo Plug
|
3.5mm Mono Plug
$0.85
Order No. 35MP |
3.5mm Stereo Plug
$1.10
3.5mm Stereo jack. Although made
for PC board mounting, they may
also be used to make "in-line"
jacks for sound-card applications. |
Quarter-inch, mono plug is often used for head phone connections and external
speaker plug. Known as the 1/4 inch mono plug. |
Quarter-inch Stereo plug is often used
in High Power Audio systems. The 1/4 inch stereo plug is also used as
Microphone input and PTT for some Collins, Drake, Heath, Ten-Tec, etc...
transceivers.
|
No, we didn't forget the radios with only two pin mic jacks. Here is a
'Two-Holer' Screw-On Microphone Connector for 2 pin jacks.
|
Sure, I remember those radios like the ole ICOM IC-22
etc, with only three pin mic jacks. Here is a 'three-hole' Screw-On Microphone Connector
for 3 pin jacks.
|
Four pin Screw-On Microphone Connector
$2.00 each or 3/$5.00
Order # CBC-4 |
Five pin Screw-On Microphone Connector
$2.00 or 3/$5.00
Order # CBC-5 |
SIX pin Screw-On Microphone Connector
$2.00 or 3/$5.00
Order # CBC-6 |
Eight pin Screw-On Microphone Connector
$2.00 or 3/$5.00
Order # CBC-8 |
Four (4) pin chassi mount connector, mate for CBC-4.
$2.00 or 3/$5.00
Order # CMC-4 |
Five (5) pin chassi mount connector, mate for CBC-5.
$2.00 or 3/$5.00
Order # CMC-5 |
Six (6) pin chassi mount connector, mate for CBC-6.
$2.00 or 3/$5.00
Order # CMC-6 |
Eight (8) pin chassi mount connector, mate for CBC-8.
$2.00 or 3/$5.00
Order # CMC-8 |
Standard 4 pin DIN Plug
Used as RTTY and CAT accessory plug I/O on some transceivers for RTTY interfacing (I/O).
$1.30 each
Order # 4PDM |
Standard 5 pin DIN Plug
Used as accessory port I/O on some transceivers for
PSK31 and SSTV sound card interfacing (I/O). Also a very popular TNC interface connector
to PacComm, MFJ, and AEA TNC, radio ports.
$1.40 each
Order # 5PDM |
Standard 7 pin DIN Plug
Used as CAT interface plug on some transceivers for Computer Aided Tuning (CAT) (I/O).
$1.50 each
Order # 7PDM |
Standard 8 pin DIN Plug
Used as accessory plug to interface data input and output to many ICOM transceivers. e.g.
PSK31 I/O, and KAM HF port.
$1.60 each
Order # 8PDM |
Standard 13 pin DIN
Plug
Used as accessory plug to interface data input and output to many Kenwood transceivers.
e.g. PSK31 I/O
$2.50 each, order no. 13PDM
With 5 ft cable, wired for KENWOOD
13 pin accessory jack, wired as follows:
Tx Audio IN =
Pin 11
Rx Audio OUT = Pin 3
PTT
= Pin 9
Gnd
= Pin 4 & 8
Shield
= Shell
ORDER No. KW13WPD @ $6.00
With 5 ft cable, wired for ICOM 13
pin accessory jack, wired as follows:
Tx Audio IN =
Pin 11
Rx Audio OUT = Pin 12
PTT
= Pin 3
Gnd
= Pin 2
Shield
= Shell
ORDER No. IC13WPD @ $6.00 |
6 pin "mini" DIN
Plug
Used as accessory plug to interface data input and output on many transceivers. e.g.
PSK31 I/O
$2.00 each
Order # 6PDMDIN
With 6
ft cable (WHITE), all pins attached with color coded wires:
$4.00 each
ORDER No.
MINIDIN 6W
|
Standard 4 pin DIN Inline Jack.
Mates 4 pin male plug above, for many interface applications
$2.50 each
Order # 4PDF |
Standard 13 pin DIN Inline Jack
Mates 13 pin DIN male (13PDM). Used as accessory jack to interface data input and output
to many Kenwood etc.. transceivers.
$3.00 each
Order # 13PDF |
Female 4 pin DIN jack may be panel mounted, or combined with another similar
connector to form an in-line adapter cable.
$2.00 or 3/$5.00
Order number = CN4PDF |
Female 5 pin DIN jack may be panel mounted, or combined with another similar
connector to form an in-line adapter cable.
$2.00 or 3/$5.00
Order number = CN5PDF |
RJ45 Plug Only!
$0.70 each
Order # RJ45P |
RJ45 with 4 ft carbon black, round,
8 conductor cable attached.
The RJ-45 modular connector is now in wide use as the
microphone connector on late model Alinco, ICOM, KENWOOD, and Radio Shack Amateur
transceivers.
$3.00 each
Order # RJ45WC |
|
AEA PK-232 Data I/O PLUG
Here it is that "Hard-to-find" plug for the AEA PK-232
TNC.
Order 232P5, $1.00 ea. or 3/$2.50
 YES,
we also have the "male" counterpart to the above "female" plug. Make an
extension, or buy both parts (see insert), and mate for other connector
applications.
Order 232M5, $1.00
ea. or 3/$2.50
|
NMO Mount CAP.
Used to cover the NMO
mount when not in use.
Comes in basic gloss
black.
YES, we have them in Stock!
The NMO cover
with built-in "0-Ring" seal.
Order NMOCAP, $2.00 ea. |
Drilled the hole in
the wrong place? Removed an old base-loaded 3/8 inch hole mount antenna;
This black rubber plug is inserted into the hole to seal from moisture. It
can be painted to blend color. The profile is about 1/8 inch high when
inserted, and 1-1/2 inch in diameter.
Price Each $1.00
Order number K-37
|
|
50 Ohm impedance, 3 ft, 6 ft, 9 ft and 100 feet. These jumpers are made
from high quality,
low-loss, coax cable with PL-259 connectors installed at each end.
Three ft. (3')
ORDER No. CX3-PLPL $4.00
Six ft. (6')
ORDER No. CX6-PLPL $5.00
Nine ft. (9')
ORDER No. CX6-PLPL $6.00
100' MINI 8 with PL-259 installed on each end,
ORDER # 100M8-PLPL $30.00
|
|
Need a spare power cable for your Alinco, ICOM, KENWOOD,
YAESU or Radio Shack transceiver...,CLICK
HERE !
|
|
Adjustable Mobile Radio mounting bracket, extends to over 9 inches width.
Order Model 220-ARB BUX price = $7.00 |
YES, They are back... after a ''sell-out'' of
this installation kit, I found some more. YES, it is really real. What you
see, is in the installation kit. This kit was used to install
trunk-mounted radios. It contains an 18 ft length of RG-58/AU coax
cable with PL-259's installed at each end, the ty-wraps, and wire with
heavy-duty AGC fuse holder,...etc, all the parts shown in the photo. This
kit will put that linear in the trunk.
Order Number = M1820;
BUX CommCo Price Each $10.00 while they last!
|
SUCH A DEAL!!!
Here is a Hi-Performance, 10
or 11 meter, mirror-mount antenna, complete with tunable whip, mirror
mount hardware, 9 feet of coax with PL-259 connectors, and ready for easy
installation.
FYI... I cut them off and
make 2 meter, luggage rack antennas of them.
Order No. MM-1011
BUX price $10.00
|
Used in PSK31 transceiver to sound-card interface, this shielded, twin
cable has two, 3.5mm stereo connectors on one end. When using with PSK31, SSTV, RTTY, and
Packet Sound card interfaces, only the "tip" of each connector is used; The
"ring" is not used. NOTE that a large ferrite core is molded into each line near
the sound card end of the cable. This is another means of preventing noise and RF feedback
between the transceiver and the PC sound card.
Twin cable is 48 inches (4 ft) long.
$3.00 each or 2/$5.00
Order # SCABLE-48 |
"WHITE" cable for your TNC
to Radio interface, or for interfacing the sound card to transceiver. Your
choice of 5 and 10 feet lengths, and has a 5 pin DIN connector
already installed on one end.
For the many transceivers (and TNCees) that have female DIN I/O jacks.
All wires are color coded.
10 ft, $4.00 or
2/$7.00
Order Number
= 5PDIN-10
5 ft, $3.00 or 2/$5.00
Order Number
= 5PDIN-.
5 |
Male, 6 pin mini DIN, for most transceivers that have ISO standard
data input/output jacks. All wires are color coded for easy signal routing.
6 foot, $4.00 each or 2/$7.00
Order MINIDIN 6W
3 foot, $2.75
each or 2/$5.00
Order
MINIDIN 3W |
3.5mm stereo male, to 3.5mm stereo female, shielded extension
cable. These are 6 ft, Heavy Duty, stereo cables. Great
for sound card extensions to RASCAL Line IN and Line OUT connections.
$2.50 each
Order 35M35F
Similar to above, but with
RCA Male (phono) to Male 3.5mm mono. This adapter cable is 6 ft.
$2.00 each
Order RCA2M35 |
DB9 Male with solder cup connections
.
$0.70 each
Order #. DB9P
DB9 Cover for DB9P above.
$1.00 each;
ORDER No. DB9C
|
1=n/c
2 = BLACK
3 = Brown
4 = RED (DTR)
5 = BARE (GROUND)
6 = YELLOW
7 = GREEN (RTS)
8 = BLUE
9 = n/c
6 ft shielded DB9 female, pins 1 and 9 are NOT connected.
$1.50 each, Order # DB9S |
9 pin DB9 female with printed circuit board solder pins.
$.50
Order No. 9FPCB
Same as above, but has straight pins (not bent to PCB).
$.50
Order No. 9FPCS |
DB9 Male to DB25 Female
Adapter.
$1.50 each
Order No.9M25F |
Black, replacement microphone.
$8.00 or 2/$15.00
Order # DM507 |
Black, curly-cord microphone or PSK/SSTV interface cable, extends to over 5
feet. This curly-cord retracts to less than 16 inches. It has 5 wires, 4 different colors,
and bare/shield.
$1.50 or 3/$4.00
Order # CURLY5 |
9 wire, curly-cord, two wires are shielded, extends 7 + ft. SUPPLY is
limited!
$2.50 each
Order # CURLY7 |
 Give your
signal some "PUNCH!" with this Amplified Power Mic. Uses "AA" 1.5
volt battery.
$15.00 each
Order No. PWRMIC |
ORIGINAL EQUIPMENT RADIO BRACKET KNOBS
3 MM
ORDER # KN3P @ 2/$1.00
4 MM
ORDER # KN4P @ 2/$1.00
5 MM
ORDER # KN5P @ 2/$1.00
6 MM
ORDER # KN6P @ 2/$1.00 |
SURGE
SUPPRESSOR
MOV (Metal Oxcide Varistor)
 Protect your 13 Volt DC transceiver(s), using the same
method used in commercial two-way mobile radio installations.
Attaches across the DC line input. Be sure connections are covered
and well insulated.
Order MOV33,
$0.80 ea. or 5/$3.00 |
CABLE
"Strain Reliefs"
Assortment of six (6) strain relief's.
for AC power, RJ11, or coax cable input/output to equipment.
Asst of 6, $1.00
ORDER No. CSR6 |
These PL-259 connectors are made of high quality material, with an ultra-low-loss,
Hi-Temp dielectric center insulator.
SPECIFY connector by type number shown below! (standard; for RG-8, RG-213,
9913..etc...)
$1.10 each, or 10/$9.00
ORDER # PL-259
|
RG-58 Reducer for "standard" PL-259.
$0.35 each each or 4/$1.00
ORDER # UG175 |
RG-59 and Mini-8 Reducer for "standard" PL-259.
$0.35 each each or 4/$1.00
ORDER # UG176 |
(Has reducer built-in to fit RG-58 small coax)
$1.25 each, or 10/$10.00
ORDER # PL-259/58
(Has reducer built-in to fit Mini 8, and
RG-59 coax)
$1.25 each, or 10/$10.00
ORDER # PL-259/M8 |
These PL-258 barrel connectors are often called ''double female.'' Ultra-low-loss,
Hi-Temp dielectric center insulator.
ORDER # PL-258
$1.25 each, or 10/$10.00 |
This VHF/UHF connector is ideal when coupling two SO-239 connectors back-to-back,
and in-line meters to SO-239. Ultra-low-loss, Hi-Temp dielectric center insulator.
ORDER # PLPLMALE
$1.50 each, or 10/$12.50 |
For bulkhead and through-the-wall UHF connector feed-thru connections,
with keeper nuts.:
Order No. 7518-2
(two inches) $2.00 each
Order No. 7518-4 (four
inches) $3.00 each
Order No. 7518-6 (six inches)
$4.00 each
Order No. 7518-NUTS (Large Nuts 2/bag) $1.00 |
When you want to co-phase those beams, quads, or build power dividers.
Ultra-low-loss, Hi-Temp dielectric center insulator.
ORDER # PLTEE
$3.00 each, or 10/$25.00 |
The Single Hole (female) chassi mounted coax connector is is supplied with mounting
hardware. Used in many applications to replace phono (RCA) jacks, and for many RF projects
that use PL-259 mating connectors.... etc...
ORDER # SO239/SH
$1.50 each, or 5/$8.00 |
The '4 hole'r' chassi mounted coax connector is attached using 4 screws. Used in
many applications to replace phono (RCA) jacks. When building coax entry panels to
communications rooms etc...
ORDER # SO239/4H
$1.50 each, or 5/$8.00 |
SO-239 Stud mount, to 3/8 X 24
threaded antenna, with tempered nylon insulator
Order # SM1 @ $3.00 each |
Fits RG-213, RG-8, etc... The connector for repeater sites and antenna that require
type ''N'' fittings.
ORDER # N-FEMALE
$3.00 each or 2/$5.00 |
Fits RG-213, RG-8, etc... The connector for repeater sites and antenna that require
type ''N'' fittings.
ORDER # N-MALE
$3.00 each or 2/$5.00 |
N-Type Female to Female Barrel.
This N to N barrel is used to mate two type N male connectors.
ORDER # N2NFEMALE
$ 4.00 each |
This right-angle connector is
ideal for inline application when you need to make a sharp 90 degree turn
with the coax, in a small place, or where the transceiver needs to be as
close to the wall as possible. Ultra-low-loss, Hi-Temp dielectric center
insulator.
ORDER # PLBOW
$2.00 each, or 10/$20.00 |
SMA
male to BNC female. Adapter for handheld antennas to new hand-held
radios.
ORDER # AT-7820
$3.50 each or 3/$10.00 |
SMA FEMALE to BNC FEMALE
ORDER # AT-7830
$3.50 each or 3/$10.00 |
SMA male to UHF (SO239)
female.
ORDER # AT-7828
$3.50 each or 3/$10.00 |
SMA FEMALE to UHF FEMALE
ORDER # AT-7839
$3.50 each or 3/$10.00
|
Mini UHF Male to
standard UHF Female.
$3.50 each
ORDER No. AT7610 |
'Adapter'' used to connect the PL259 UHF male to
Auto Radio type female. This adapter is also used to connect to RCA
type connectors, and most often used to connect UHF (PL259) male to
scanner ports equipped with auto antenna type jack.
ORDER # TA 7702
$2.50 each, or 10/$20.00 |
Best known as the ''adapter'' used to connect the mobile PL-259 connector to the
hand-held BNC antenna port.
ORDER # UHFF2BNCM
$1.50 each, or 10/$12.50 |
'adapter'' used to connect the BCN male antenna to SO239
female
UHF. This is a BNC female to UHF (PL259) male adapter.
ORDER # BNCF2UHFM
$2.50 each, or 10/$20.00 |
TA7001A
BNC MALE Crimp Type for RG-58/U coax
$2.00 each, or 10/$15.00 |
TA7001B
BNC MALE Crimp Type for RG-59/U coax
$2.00 each, or 10/$15.00 |
TA7003A
BNC MALE for RG-58/U
coax, for Crimp and Molding.
$2.00 each, or 10/$15.00 |
TA7003B
BNC MALE for RG-59/U
coax, for Crimp and Molding.
$2.00 each, or 10/$15.00 |
TA7006A
BNC MALE for RG-58/U
coax, CLAMP type.
$2.25 each, or 10/$16.00 |
TA7003B
BNC MALE for RG-59/U
coax, CLAMP type.
$2.25 each, or 10/$16.00 |
TA7022A
BNC FEMALE for RG-58/U
coax, CLAMP type.
$2.40 each, or 10/$17.00 |
TA7022B
BNC FEMALE for RG-59/U
coax, CLAMP type.
$2.40 each, or 10/$17.00 |
|
For
a full page of RF Connectors and Adapters, CLICK
HERE !
|
AGC Type/size fuses
(5/$1)ORDER by Value
Number
5 AMPFUSE
10 AMPFUSE
15 AMPFUSE
20 AMPFUSE
25 AMPFUSE
30 AMPFUSE
35 AMPFUSE
$1.00 per box
5 boxes / $4.00
10 boxes/ $7.00
Sorry, no mixed values/box
|
AMPLIFIED SPEAKER
A
"BUX Best Buy"
top quality, brand name.
A great addition to the HAM
shack as an audio signal tracer, or for hand-held transceivers. Just
add 12 volts DC, and plug it into the external speaker jack, and you have
sound that is better than full sized transceiver speakers. Use it
with your "hand-held" in the mobile. This amplified speaker
delivers 8 watts of audio.
Hook-up is simple; Connect the Orange wire (with 2 amp fuse, and
holder supplied) to 12 volts DC. Black lead to ground. The other
pair of wires go to low level (150 to 200 mV) audio or to the external
speaker jack. Comes complete with a durable mounting bracket, hardware,
red LED power-ON indicator and volume control. Size is approximately
6"w X 4"h
New, in original carton.
"BUX
DEALERS, Best Buy"
Order # AMPSPKR |
RCA (phono)
plug, solder type,
similar to above.
ORDER # RCA-MALE
$ .60 each or 2/$1.00
Field Day, Some Day, Any Day.. or for the RV,
here is a cigarette lighter receptacle with battery clips attached.
This connection enables you to power an external 12 VDC device from your
12 volt DC vehicle battery.
Leads and battery CLIPS are
colored RED (positive) and BLACK (negative).
ORDER No.
CIGCLIP
$3.50 each |
|
Five, 3/16 inch ferrite
beads.
No, the LED is for size comparison only. These ferrite beads are used in
may HF and VHF projects to minimize stray RF. Slip one over the mic audio
input lead to reduce RF audio feedback.
$1.00 per bag of 5 ORDER No.
FBEAD73 |
Simi-Hard rubber knobs fit 1/4" shaft. This knob has a nice look and feel
to it for any project. The half-moon insert can be removed, and the 2 set
screws will attach the knob to "round" 1/4 inch shaft.
1-1/2" diameter.
$1.00 per bag of 2.
ORDER No. RUBRKNOB |
|
PLUG & JACK COMBO
1/4 inch Stereo, Plug & Jack set. Complete
with all mounting hardware. Jacks are "closed-circuit" type, however they
may be wired configured as; Mono, Stereo, or Open-Circuit. 1/4 inch
plug is same as "25SMIC" shown below.Price per set (Plug & Jack)
$2.00
Order No. PJ25 |
SOLDER
Top Quality Solder, Made In USA !! A full pound roll (net) of solder.
Diameter is .020, alloy SN 63%, PB 37%, flux WRMA/P2, OEM & MIL
Spec.
Price per roll = $6.50 or 2
rolls for $12.00
ORDER No. SOLDER |
