Remember how dark it is behind your transceiver...and how difficult it is to find the  I/O jack on the rear panel of your transceiver?  That's no longer a problem. We provide a FREE Flash-Lite with each RASCAL to help you find the accessory jack on the dark-side of your radio.With the RASCAL GLX, The Total cable length between transceiver and PC exceed 10 feet.  As with most  Sound Card software, be sure your PC is equipped with a  Creative Labs or SB16 compatible sound card, to provide the features and support for;  PSK31,  SSTV,  EchoLink,  Packet,  RTTY (FSK & AFSK), eQSO, WJST, APRS, CW, MT63, and more. ALL ORDERS ARE SHIPPED SAME DAY RECEIVED, except sunday and holidays   Got more than one transceiver?  Now you can operate the sound card modes without buying additional interfaces.  Simply change from your HF transceiver to the VHF/UHF transceiver by unplugging the HF cable and inserting a different transceiver cable. By using transformer isolation for the transmit and Receive audio paths, we prevent ground loop coupling, and reduce the chance of RF feedback into the PC sound card (squeals, hum, etc).  To further reduce RF feedback and RF ingress into the Tx or Rx sound card audio, we install a large (molded) ferrite core over the RASCAL to sound card audio I/O cable(s). The end result is clean, clear, audio, reproduction on-the-air. An added benefit of these preventive measures is IMD reduction.  RASCAL��GLX, are in-stock, tested, and ready to ship!

 

	No external power supply required.
	No case screws to remove and replace when you want to change radios.
	No jumpers to juggle.
	Input/output is fully isolated using BuxComms isolation coupling transformers to prevent hum-loops and RF feedback.
	RFI, Noise and Distortion proof, using high quality, shielded audio cables with ferrite noise attenuators.
	High quality, silk screened, fiber glass, printed circuit board
	Compact size ABS case is color coordinated to match PC and related HAM gear.
	Easiest Setup of any sound card interface available, virtually Plug-N-Play.
	Supplied with PC comport (6 ft) cables, and RASCAL GLX, to radio cable is 6 ft. Overall length exceeds 10 feet.
	PC Cables, One set of RASCAL GLX, to Radio cables, Connectors, Components, and Complete documentation are included.
	Each RASCAL GLX, is fully tested before shipping.
	Added circuitry for hard-key'd CW for use with CBL CW cable and multimode software
	Added circuitry for use when using transceivers with true FSK (RTTY) output.
	Includes a CD ROM of PSK31 Software, Pictorial diagrams, & RASCAL GLX,Tech Support files. Sorry, we do not support soundcard program software.  For soundcard software & program support, contact the software vendor or author.
	Hardcopy Schematics, Documents, and Easy to follow Setup instructions.
	Clear lense covered "red" LED transmit indicator.
	RASCAL GLX,� is the ideal sound card interface for portable and field-day operations.
	Automatic PTT control is activated via the PC serial comport via software.
	To further reduce CPU noise, the serial comport  6 ft cable is high quality, with foil and drain wire shielding.
	An EZ access, transmit level control for transceiver transmit audio control.

 

ALINCO       We Accept   Mail order or FAX form CLICK HERE!
To view diagram, click the shopping cart for that model. CBL Model No.  ↓	DESCRIPTION, Make and Model of Transceiver ←One CBL FREE with each RASCAL GLX.  →	Additional RASCAL to Radio CBLs are $12.95 Each. Each $39.95 RASCAL includes one FREE RASCAL to Radio cable (CBL).
CBL-AL8M	Alinco 8 pin screw-on mic & Ext Spkr I/O
CBL-20	Alinco Hand-Helds with 2.5mm & 3.5mm I/O
CBL-AL45	Alinco RJ45 I/O modular connector For ALINCO model: DR-605
CBL-AL6A	Alinco 8 pin screw-on mic with receive at 3.5mm jack. For ALINCO models: DX-70, DR-119, DR-1200
CBL-DJ25S	Alinco DJ-100T, 120T, 200T, & DJ-500
CBL AL135	Alinco DR-135 DataRadio
CBL MDIN	CBL MDIN is our most popular cable (CBL). Most late model transceivers are now equipped with this 6 pin Mini DIN, ISO 9002 standard data input/output jack, including, Alinco, Icom, Kenwood, Azden, Radio Shack, and YAESU.  If your radio has the 6 pin Mini DIN, Data I/O jack, then by all means use it. Using this jack, enables the use of your microphone, while operating SSTV, etc... Order as many extra cables (CBL) with the Shopping Cart as you wish, but keep in mind that one CBL is free with each RASCAL GLX, GLB, or GLK you order. The free cable(s) (CBL) you select should not be 'ADDED to the Shopping Cart, instead, the free CBL should be entered in the CBL Model space on the Secure Checkout form. A space is provided on the Secure Checkout form for both 'COMMENTS' and 'CBL Model'.
NOTICE:  Alternate method for FREE CBL. Enter the RASCAL GLX (engine) in the Shopping Cart, then use the ''CBL Model'' or "COMMENTS:" space in the Shopping Cart Check-Out form to enter the (free) CBL model number.  One CBL FREE with each RASCAL ordered.
AZDEN         We Accept   Mail order or FAX form CLICK HERE!
To view diagram, click the shopping cart for that model. CBL Model No.  ↓	DESCRIPTION, Make and Model of Transceiver ←One CBL FREE with each RASCAL GLX.  →	Additional RASCAL to Radio CBLs are $12.95 Each. Each $39.95 RASCAL includes one FREE RASCAL to Radio cable (CBL).
CBL-MDIN	AZDEN 6 pin Mini DIN  for PCS 9000 Data Port
CBL AZMX	AZDEN transceivers with 8 pin screw-on mic and 3.5mm Ext Spkr Plug
COLLINS        We Accept   Mail order or FAX form CLICK HERE!
To view diagram, click the shopping cart for that model. CBL Model No.  ↓	DESCRIPTION, Make and Model of Transceiver ←One CBL FREE with each RASCAL GLX.  →	Additional RASCAL to Radio CBLs are $12.95 Each. Each $39.95 RASCAL includes one FREE RASCAL to Radio cable (CBL).
CBL-75767	Transceivers with Patch IN, Patch OUT, and PTT RCA jacks
CBL-CW	RASCAL to transceiver cable for hard-keyed CW operating
DRAKE    We Accept   Mail order or FAX form CLICK HERE!
To view diagram, click the shopping cart for that model. CBL Model No.  ↓	DESCRIPTION, Make and Model of Transceiver ←One CBL FREE with each RASCAL GLX.  →	Additional RASCAL to Radio CBLs are $12.95 Each. Each $39.95 RASCAL includes one FREE RASCAL to Radio cable (CBL).
CBL-TR7	DRAKE 4 pin screw-on mic with 1/8" Ext Spkr jack Models  TR-7 or TR-7/A, and some  TR-22, TR-33, TR-7, UV-3 radios
CBL-TT25	DRAKE TR-4, TR-4C, TR-4CW, and TR-6 radios. Only  the standard 1/4 inch Stereo plugs are supplied!  SwitchCraft 230 (Collins) type 3-circuit MIC plug are NOT included. Similar interface to Drake "TWINS." (R4B & TX4B)
CBL-CW	RASCAL to transceiver cable for hard-keyed CW operating
ICOM     We Accept   Mail order or FAX form CLICK HERE!
To view diagram, click the shopping cart for that model. CBL Model No.  ↓	DESCRIPTION, Make and Model of Transceiver ←One CBL FREE with each RASCAL GLX.  →	Additional RASCAL to Radio CBLs are $12.95 Each. Each $39.95 RASCAL includes one FREE RASCAL to Radio cable (CBL).
CBL-IC8M	ICOM HF, VHF,/UHF Transceivers w/8 pin Screw-On MIC & Ext Spkr jack. ICOM models IC-120, IC-1201, IC-1271, IC-1275, IC-228, IC-22U, IC2400, IC-25, IC-2500, IC-255, IC-251A, IC-260, IC-27, IC-271, IC-275, IC-28, IC-290, IC-3200, IC-3210, IC-3220, IC-375, IC-37A, IC-38A, IC-45, IC-47, IC-471, IC-475, IC-48, (IC-718 see also RASCAL IC13), IC-490, IC-505, IC-551, IC-560, IC-575, IC-723, IC-732, IC-751, IC-735, IC-737, IC-761, IC-765, IC-781, IC-901, IC-2310, IC-2410, IC746,  756, 760PRO, 775DXII, and other Icom transceivers with 8 pin, screw-on mics.  Includes Icom IC-707, IC-720, IC-730, IC-740, IC-745, and IC-751,
CBL-IC8PD	ICOM  HF-, Transceivers with 8 pin DIN accessory jack ICOM Models:  IC-275, IC-475, IC-721, IC-723, IC-725, IC-726, IC-728, IC-729, IC-732, IC-735, IC-736, IC-737, IC-737A, IC-738, IC-746, IC-746,<HF>IC746PRO, IC-756, IC-756PRO, IC-756PROII, IC-760/Pro, IC-761, IC-765, IC-775, IC-775DSP, IC-780, IC-781, IC-820, IC-821H, IC-910H, IC-970E, IC-970H, IC-1275,  IC-2000 and other Icom transceivers with 8 pin DIN accessory I/O ports.  AND MORE !
CBL 746V	This is a SPECIAL built cable for use with the Icom 746 & 756 series for use at VHF  (NOT HF).  Note price of this CBL is 19.95
CBL-IC13RY	ICOM  Transceivers with 13 pin DIN accessory jack w/ FSK pin. Wired for HF use.  BEST CHOICE for Icom IC-706 mk II & IC-718;
CBL-IC13VU	ICOM  Transceivers with 13 pin DIN accessory jack wired for VHF/UHF operation For Icom IC-706 mk II and ICOM transceivers with similar I/O jack.
CBL-MDIN	Six pin mini DIN (VHF) jack for the706 and, transceivers with this I/O  Most used for VHF operation with the 706 MK II, IC-207H and ICOMs with similar I/O
CBL-IC45	ICOM HF, VHF, and UHF transceivers with RJ-45 Modular Mic jacks ICOM models: IC-207H, 2720, 2800, 703, IC-706, IC-718, IC-V8000, IC-281, IC-381, IC-481, IC-681, IC-2000, IC-2100, 2350, 2340, and similar Icom I/O.  (Note: for 706 & 718, most ops prefer CBL IC13RY)
CBL-IC4M	ICOM HF-VHF Transceivers with 4 pin screw-on mic & Ext Spkr ICOM models IC-202, IC-215, IC-22S, IC-245, IC-280, IC-402, IC-502, etc...
CBL-20	ICOM, handheld transceiver(s) with 2.5mm & 3.5mm jacks Icom W32A, W32E, IC-T7A, T7E, IC-T8A, T8E, and Icom Hand Helds with similar I/O. NOTE: Be sure your Hand-Held uses the same connector format: 2.5mm (TxAFSK/PTT) and 3.5mm (Rx AF).
CBL-CW	RASCAL to transceiver cable for hard-keyed CW operating
NOTICE:  Alternate method for FREE CBL. Enter the RASCAL GLX (engine) in the Shopping Cart, then use the ''CBL Model'' or "COMMENTS:" space in the Shopping Cart Check-Out form to enter the (free) CBL model number.  One CBL FREE with each RASCAL ordered.
CBL MDIN	CBL MDIN is our most popular cable (CBL). Most late model transceivers are now equipped with this 6 pin Mini DIN, ISO 9002 standard data input/output jack, including, Alinco, Icom, Kenwood, Azden, Radio Shack, and YAESU.  If your radio has the 6 pin Mini DIN, Data I/O jack, then by all means use it. Using this jack, enables the use of your microphone, while operating SSTV, etc... Order as many extra cables (CBL) with the Shopping Cart as you wish, but keep in mind that one CBL is free with each RASCAL GLX, GLB, or GLK you order. The free cable(s) (CBL) you select should not be 'ADDED to the Shopping Cart, instead, the free CBL should be entered in the CBL Model space on the Secure Checkout form. A space is provided on the Secure Checkout form for both 'COMMENTS' and 'CBL Model'.
CBL-QRP+	INDEX LABS "QRP+"
KENWOOD     We Accept   Mail order or FAX form CLICK HERE!
To view diagram, click the shopping cart for that model. CBL Model No.  ↓	DESCRIPTION, Make and Model of Transceiver ←One CBL FREE with each RASCAL GLX.  →	Additional RASCAL to Radio CBLs are $12.95 Each. Each $39.95 RASCAL includes one FREE RASCAL to Radio cable (CBL).
CBL-KW8M	KENWOOD Transceivers with 8 pin Screw-On mic & Ext Spkr I/O KENWOOD models: TM-201, TM-221, TM-231, TM-241, TM-2530, TM-401, TM-421, TM-431, TM-441, TM-531, TM-541, TM-621, TM-631, TM-701, TM-721, TM-731, TR-3200, TR-50, TS-50/S, TS-60, TS-751, TS-851, TS-140, TS-430, TS-440, TS-450, TS-660, TS-670, TS-680, TS-690, TS-701, TS-711, TS-780, TS-790, TS-811, TS-850, TS-870, TS-930, TS-940, TS-950, TW-4000, 4100, and Kenwood transceivers with 8 pin screw-on Mic connectors
CBL-KW13RY	Kenwood  Transceivers with 13 pin DIN accy  with FSK "pin." For most Kenwood transceivers with 13 pin DIN with FSK pin, TS2000 etc.
CBL-KW13RYR	Kenwood TS-850 and KW Transceivers with 13 pin DIN accy and "FSK RCA Jack" For TS-850 Kenwood transceivers with 13 pin DIN and RTTY/FSK "RCA Jack".
CBL-KW4013	Early KENWOOD HF Transceivers with 13 pin DIN accessory jack       TS-940, 440... etc
CBL-MDIN	KENWOOD Transceivers with 6 pin mini DIN (ISO standard) jack (KENWOOD Models: TM-255, TM-455, TM-733, TM-833, TM-G707, TM-V7A,  TM-G 707A, (Delta) D-700 and transceivers with 6 pin mini DIN data I/O)
CBL-THF6	KENWOOD HandHeld Transceivers with 3.5mm & 2.5mm "stereo" I/O   (KENWOOD Models: TH-F6A, TH-F7E and transceivers with similar I/O)
CBL-KW45	KENWOOD HF and VHF Transceivers with (RJ45) MODULAR mic TM-251, TM-2400, TM-255, TM-261, TM-451, TM-455, TM-461, TM-643, TM-732, TM-733, TM-741, TM-742, TM-833, TM-841, TM-842, TM-941, TM-942, and Kenwoods with RJ45 mic jacks
CBL-KW4M	KENWOOD HF Transceivers w/4 pin screw-on mic & Ext Spkr jack TS-120, TS-130, TS-180, TS-311, TS-510, TS-511, TS-520, TS-530, TS-600, TS-700, TS-770, TS-801, TS-820, TS-830, TS-900, TX-310, TR-1300, TR-2200, TR-5200, TR-2300, TR-7010, TR-7200, TR-7400, TR-7500, TR-8000, TR-8200, TR-8300, and more)
CBL-KW6M	KENWOOD HF Transceivers with 6 pin screw-on mic & Ext Spkr jack TR-7730, TR-7750, TR-7800, TR-7850, TR-7930, TR-7950, TR-8400, TR-9000, TR-9130, TR-9500, and other Kenwood transceivers with 6 pin screw-on mic connectors
CBL-CW	RASCAL to transceiver cable for hard-keyed CW operating
NOTICE:  Alternate method for FREE CBL. Enter the RASCAL GLX (engine) in the Shopping Cart, then use the ''CBL Model'' or "COMMENTS:" space in the Shopping Cart Check-Out form to enter the (free) CBL model number.  One CBL FREE with each RASCAL ordered.
CBL MDIN	CBL MDIN is our most popular cable (CBL). Most late model transceivers are now equipped with this 6 pin Mini DIN, ISO 9002 standard data input/output jack, including, Alinco, Icom, Kenwood, Azden, Radio Shack, and YAESU.  If your radio has the 6 pin Mini DIN, Data I/O jack, then by all means use it. Using this jack, enables the use of your microphone, while operating SSTV, etc... Order as many extra cables (CBL) with the Shopping Cart as you wish, but keep in mind that one CBL is free with each RASCAL GLX, GLB, or GLK you order. The free cable(s) (CBL) you select should not be 'ADDED to the Shopping Cart, instead, the free CBL should be entered in the CBL Model space on the Secure Checkout form. A space is provided on the Secure Checkout form for both 'COMMENTS' and 'CBL Model'.
Radio Shack    We Accept   Mail order or FAX form CLICK HERE!
To view diagram, click the shopping cart for that model. CBL Model No.  ↓	DESCRIPTION, Make and Model of Transceiver ←One CBL FREE with each RASCAL GLX.  →	Additional RASCAL to Radio CBLs are $12.95 Each. Each $39.95 RASCAL includes one FREE RASCAL to Radio cable (CBL).
CBL-HTX10	Radio Shack HTX-10
CBL-HTX100	Radio Shack Model HTX-100
CBL-HTX242	Radio Shack Model HTX-212, and HTX-242  or RS 45
CBL-HTX252	Radio Shack HTX-252
CBL-20	Radio Shack HTX-202 & HTX-404
CBL MDIN	CBL MDIN is our most popular cable (CBL). Most late model transceivers are now equipped with this 6 pin Mini DIN, ISO 9002 standard data input/output jack, including, Alinco, Icom, Kenwood, Azden, Radio Shack, and YAESU.  If your radio has the 6 pin Mini DIN, Data I/O jack, then by all means use it. Using this jack, enables the use of your microphone, while operating SSTV, etc... Order as many extra cables (CBL) with the Shopping Cart as you wish, but keep in mind that one CBL is free with each RASCAL GLX, GLB, or GLK you order. The free cable(s) (CBL) you select should not be 'ADDED to the Shopping Cart, instead, the free CBL should be entered in the CBL Model space on the Secure Checkout form. A space is provided on the Secure Checkout form for both 'COMMENTS' and 'CBL Model'.
NOTICE:  Alternate method for FREE CBL. Enter the RASCAL GLX (engine) in the Shopping Cart, then use the ''CBL Model'' or "COMMENTS:" space in the Shopping Cart Check-Out form to enter the (free) CBL model number.  One CBL FREE with each RASCAL ordered.
RCI       We Accept   Mail order or FAX form CLICK HERE!
To view diagram, click the shopping cart for that model. CBL Model No.  ↓	DESCRIPTION, Make and Model of Transceiver ←One CBL FREE with each RASCAL GLX.  →	Additional RASCAL to Radio CBLs are $12.95 Each. Each $39.95 RASCAL includes one FREE RASCAL to Radio cable (CBL).
CBL-RCI6	RCI 5054 and RCI radios with 6 pin screw-on MIC This interface uses the 3.5mm external speaker jack for receive AF, and requires SwitchBox for SSTV.
SBE 34     We Accept   Mail order or FAX form CLICK HERE!
To view diagram, click the shopping cart for that model. CBL Model No.  ↓	DESCRIPTION, Make and Model of Transceiver ←One CBL FREE with each RASCAL GLX.  →	Additional RASCAL to Radio CBLs are $12.95 Each. Each $39.95 RASCAL includes one FREE RASCAL to Radio cable (CBL).
CBL-SBE34	SIDEBAND ENGINEERS model SBE 34 This interface provides open-end connection for the SBE34  external speaker screws..  Tx AF input and PTT is to the 1/4"  MIC jack.
NOTICE:  Alternate method for FREE CBL. Enter the RASCAL GLX (engine) in the Shopping Cart, then use the "COMMENTS:" space in the Shopping Cart Check-Out form to enter the (free) CBL model number.  One (1) CBL FREE with each RASCAL GLX ordered.
SGC    We Accept   Mail order or FAX form CLICK HERE!
To view diagram, click the shopping cart for that model. CBL Model No.  ↓	DESCRIPTION, Make and Model of Transceiver ←One CBL FREE with each RASCAL GLX.  →	Additional RASCAL to Radio CBLs are $12.95 Each. Each $39.95 RASCAL includes one FREE RASCAL to Radio cable (CBL).
CBL-2020	SGC model SG-2020 This interface uses the 3.5mm external speaker jack to extract receive audio.
Ten Tec     We Accept   Mail order or FAX form CLICK HERE!
To view diagram, click the shopping cart for that model. CBL Model No.  ↓	DESCRIPTION, Make and Model of Transceiver ←One CBL FREE with each RASCAL GLX.  →	Additional RASCAL to Radio CBLs are $12.95 Each. Each $39.95 RASCAL includes one FREE RASCAL to Radio cable (CBL).
CBL-5PD	Ten-Tec with 5 pin DIN data I/O accessory jack Ten-Tec PEGASUS,  Jupiter, (538),  and radios with similar 5 pin DIN data I/O.
CBL-ORION	Ten-Tec ORION (565) Ten-Tec Orion transceivers with AUX I/O, 8 pin DIN jack.
CBL-OMNI	For Ten-Tec transceivers with;  PTT,  Tx IN, Rx IN RCA jacks: Ten-Tec OMNI V, & OMNI VI (Late Model Paragon, and Corsair) and transceivers with RCA jacks for ''Patch IN, Patch OUT, and PTT'' jacks.
CBL-TT25	Ten-Tec transceivers with 1/4 inch Mic and Ext Spkr jacks: Early Ten-Tec Triton 544,  Argonaut 505, 509, 515, (*early Omni V see late model; R-TTOMNI) below), and other Ten-Tec HF Transceivers with 1/4 inch Stereo Mic I/O and 1/4 inch mono external speaker jack.  NOTE: This interface cable works with other vintage transceivers; eg; Atlas, Swan,Drake, etc...
CBL-TT4M	Ten-Tec transceivers w/4 pin screw-on mic & 1/4" Ext Spkr I/O
CBL-CW	RASCAL to transceiver cable for hard-keyed CW operating
UNIDEN   We Accept   Mail order or FAX form CLICK HERE!
To view diagram, click the shopping cart for that model. CBL Model No.  ↓	DESCRIPTION, Make and Model of Transceiver ←One CBL FREE with each RASCAL GLX.  →	Additional RASCAL to Radio CBLs are $12.95 Each. Each $39.95 RASCAL includes one FREE RASCAL to Radio cable (CBL).
CBL-UNIDEN5MX	UNIDEN and some HR2510  with 5 pin Screw-On Mic and Ext Spkr jack.
YAESU   We Accept   Mail order or FAX form CLICK HERE!
To view diagram, click the shopping cart for that model. CBL Model No.  ↓	DESCRIPTION, Make and Model of Transceiver ←One CBL FREE with each RASCAL GLX.  →	Additional RASCAL to Radio CBLs are $12.95 Each. Each $39.95 RASCAL includes one FREE RASCAL to Radio cable (CBL).
CBL-Y8M	YAESU transceivers with 8 pin (screw-on) mic input. Receive audio be taken from the external speaker jack.   YAESU models: FT-1, FT-77, FT-102, FT-107, FT-211, FT-290 MKII, FT-480, FT-690 MKII, FT-707S, FT-712, FT-726, FT-736, FT-747, FT-757, FT-767, FT-770, FT-840, FT-850, FT-790 MK II, FT-912, FT-980,  FT-990, FT-1000, FT-2200, FT-2700, FT-5100, FT-7200, FT-840, FT-890, FT-4700, FT-212, FT-ONE-S, FT-650, 707, 712, 726, 736, 756, 767, 77, 790II, 700, 840, 890, 990, 1000D  and MORE,
CBL-Y4M	YAESU transceivers with 4 pin (screw-on) mic input Receive audio is from the external speaker jack.   YAESU models: having 4 pin screw-on microphones.
CBL-MDIN	YAESU transceivers having a, 6 pin Mini DIN for data I/O YAESU  FT-817,  FT-100, FT-897, FT-1500, FT-3000, FT-8000, FT-8100, FT-8500, and FT-857   etc.. and   *FT-847 "VHF" port.
CBL-847HF	YAESU FT-847  3.5mm HF Data I/O HF jack For Yaesu FT-847 "HF"  Data Jack (*NOTE: see CBL MDIN for 847 VHF operation
CBL-FT600+	YAESU FT-736, FT-600, FT-890, & Late Model FT-900.  3.5mm HF Data I/O HF jack PTT  is via RCA "PTT" Jack.
CBL-YX	YAESU hand-held transceivers with 4 circuit, 3.5mm I/O jack. YAESU  FT-10, FT-40, FT-50, VX-1, VX-5, VX-150, and Yaesu handhelds with similar I/O.
CBL-FT2500	YAESU FT-2500M 2400 & Yaesu transceivers with similar I/O YAESU FT-2500, 2500M, 2400,  etc
CBL-FT2600	YAESU FT-2600 & Yaesu transceivers with   DB9f   I/O YAESU FT-2600, 2600M,  etc
CBL-FT2800	YAESU FT-2800 & Yaesu transceivers with   RJ 12 Mic & 3.5mm Ext Spkr  YAESU FT-2800, 2800M,  etc
CBL-75767	YAESU transceivers using the rear panel RCA jacks; YAESU FT-102, FT-757, FT-767, FT-920, etc
CBL-5PD	YAESU FT-1000"Mark V"  Transceiver PSK31 Interface   Use also with YAESU FT-920 (insure that data mode switch is in AFSK position)  SPECIAL NOTE: Use the FT1000 MkV, "EASY SET" to configure 5 pin DIN, Packet jack, for USB. For FSK/RTTY operation, Use cable CBL FT4RY  (see below, FSK only!)
CBL FT900/e	Early model YAESU FT-900 and Yaesu transceivers with similar I/0 For LATE model FT-900, see CBL F600 above. For FSK/RTTY operation, Use cable CBL FT4RY  (see below, FSK only!)
CBL FT990	YAESU FT-990 and Yaesu transceivers with similar I/0 For FSK/RTTY operation, Use cable CBL FT4RY  (see below, FSK only!)
CBL-1000D	YAESU FT-1000"D"  Transceiver PSK31 Interface cable For FSK/RTTY operation, Use cable CBL FT4RY (see below, FSK only!)*
CBL-1000MP	YAESU FT-1000"MP"  Transceiver PSK31 Interface cable For FSK/RTTY operation, Use cable CBL FT4RY (see below, FSK only!)*
CBL-FT4RY	YAESU transceivers with 4 pin DIN RTTY jacks  NOTE:  This cable enables FSK/RTTY operation only.
CBL-20	YAESU  FT-51R & Yaesu handhelds with similar I/O Yaesu handheld transceiver(s) using similar 2.5mm (TxAFSK/PTT)  and 3.5mm (Rx AF) "mono" I/O
CBL-CW	RASCAL to transceiver cable for hard-keyed CW operating
CBL MDIN	CBL MDIN is our most popular cable (CBL). Most late model transceivers are now equipped with this 6 pin Mini DIN, ISO 9002 standard data input/output jack, including, Alinco, Icom, Kenwood, Azden, Radio Shack, and YAESU.  If your radio has the 6 pin Mini DIN, Data I/O jack, then by all means use it. Using this jack, enables the use of your microphone, while operating SSTV, etc... Order as many extra cables (CBL) with the Shopping Cart as you wish, but keep in mind that one CBL is free with each RASCAL GLX, GLB, or GLK you order. The free cable(s) (CBL) you select should not be 'ADDED to the Shopping Cart, instead, the free CBL should be entered in the CBL Model space on the Secure Checkout form. A space is provided on the Secure Checkout form for both 'COMMENTS' and 'CBL Model'.
NOTICE:  Alternate method for FREE CBL. Enter the RASCAL GLX (engine) in the Shopping Cart, then use the ''CBL Model'' or "COMMENTS:" space in the Shopping Cart Check-Out form to enter the (free) CBL model number.  One CBL FREE with each RASCAL ordered.
If you would like instructions explaining how to setup the RASCAL and EchoLink to an Icom 706 and similar HF/VHF radios, send us an Email with your return Email address. We'll send the (pdf) file, return eMail CLICK HERE!
We Accept   Mail order or FAX form CLICK HERE!
USB to SERIAL Adapter  OK, so you have a new PC with only a USB port, and no serial port....  Not so, any more.  BUX Comm has the answer.  This USB to Serial comport converter meets the specs shown below, and enables  you to operate the RASCAL� interface(s) from a PC USB port.  Also enables the use of TNC I/O and other serial comport devices. USB  V1.1 Compliant Supports Windows� 98/2000/ME and CLICK HERE to Download XP drivers Installation driver CD (included) installs serial port instantly Supports baud rates from 1,200 to 115,200 K Great addition for the new LapTop that came without a serial comport. Drives the BUX Comm RASCAL"� for Auto-PTT in PSK31. etc. USB2SC   We Accept   Mail order or FAX form CLICK HERE!

Our Lil Lite that we include with each RASCAL GLX. Additional lil lites are available at 99 cents each. Batteries are included. Perfect solution for finding the correct comport, or accessory jack on the dark sides of your PC or back of your transceiver. Also doubles as a sturdy "key-ring." LILITE LILITE
Cables and Accessories   IMPORTANT NOTE;  Prices of cable assemblies shown, do NOT include shipping & handling.   All orders are shipped within 24 hours of receiving, via USPS PRIORITY MAIL, FED-X Ground, or UPS.   Shipping & Handing added to each interface cable order: USA=$7.90, CANADA =$9.90, Foreign=$15.90 Below are cable assemblies you can use to make your  RASCAL GLX or TNC to Radio interface cables.
8 pin DIN male plug wired with 6 ft cable.  All 8 pins are connected, wires are color coded, and include one drain/shield wire.  For use with ICOM, and radios with 8 pin DIN accessory jacks. May also be used to interface KAM and KAM PLUS HF ports to various transceivers. ORDER 8D  $4.99
Make your own RASCAL GLX or TNC2 to Radio interface using this ready made cable.  The 5DMX cable is 6 feet long, the 5 pin (male) DIN and  3.5mm external speaker plug are already attached and wired to the 5 pin DIN.  All you add is the mating connector for the transceiver end.  The cable is prepped with 1/2 inch of each wire exposed, and 1/8 inch bare wire stripped and solder tinned for easy radio plug installation. Cable is almond color.    $5.99 each,  Order model 5DMX
This is our cable model "KVXT" which is used to make the TinyTrak, Kantronics VHF or 1200 baud cable, and in some cases, may be used to fabricate the KAMxl cables. You add only the transceiver MIC or Accessory connector. It is also used to make the Tiny-Trak interface cable.  All you add is the Radio or transceiver connector for the accessory connector. Order KVXT 5.99   KVXT Pre-Fab Cable,  diagram shown below.
SIX (6) foot shielded cable with all 8 wires attached to the 8 pin screw-on microphone connector. Got a new "super-mic", or need to interface another device to the mic jack.... here's the solution.   $4.99 each Order 8M
13 pin DIN male plug wired with 6 ft (straight) cable.  All 13 pins are connected, wires are color coded, and include one drain/shield wire.  For use with KENWOOD, ICOM, and radios with 13 pin DIN jacks.      $5.99 ea. ORDER No. 13D
4 circuit, 3.5mm Plug and Coiled Cable For YAESU VX-1, VX-5, FT-10, FT-40, & FT-50, etc... Tip = 1 Ring  1 = 2 Ring  2 = 3 Sleeve = 4  Order Model. VX4 $2.99
The solution for TNC to H-T interfacing for mobile and portable APRS operation.  Of course, it makes a heavy-duty replacement cable for the Speaker-Mic.  Standard Mic/Earphone 2.5mm & 3.5mm molded plug spacing.  Easily extends more than six feet. Small tip = RED,  Small Sleeve=Shield/Black Large Tip = Yellow,    Large Sleeve = White  Order No. 34558   $2.99
AEA PK232 RAD1/RAD2 PREWIRED CABLE & CONNECTOR This cable is six (6') feet long, wired to the 5 pin molex type connector for AEA PK232 Radio ports. White wire = TX audio Bare wire  = Shield/Ground Red wire  = Push-To-Talk (PTT) Blue ware  = Receive Audio  Order Model  A232CBL   $3.99
CLICK HERE for MORE AUDIO CABLES & CONNECTORS
Stereo "Y" connector, also works great with MONO applications, as "ring" is not used when connected into mono jack. Use with TNC / KPC/KAM when using external speaker jack.  Allows both the TNC and External Speaker for receive audio. Order, YCONN 99 cents each   RASCAL & SOUND CARD uses 2, YCONN	Sound card six ft male to female stereo extender cables (1/8") or 3.5mm stereo male, to 3.5mm stereo female, shielded extension cable.  These are  6 ft, high-quality, stereo cables.  Great for sound card stereo extensions to RASCAL Line IN and Line OUT or MIC IN/SPKR OUT jacks.  35MFSTX2  $2.99 /pair   Set of 2 for soundcard I/O..
RASCAL TO PC EXTENDER KIT This cable kit allows you to space your PC and transceiver more than 15 feet apart.  This kit contains: One (1) db9 female, to db9 male cable 6 feet, serial comport cable,  and Two (2) 3.5mm stereo female to male, sound card cables. Combined with the 6 ft RASCAL to transceiver cables, and 6 ft, RASCAL GLX to PC cables, you can separate the radio and PC more than 15 feet. $3.99 Order Model  RXK
Make your own CBL, using this ready made cable.  The 5DMX cable is 6 feet long, the 5 pin (male) DIN and  3.5mm external speaker plug are already attached and wired to the 5 pin DIN.  All you add is the mating connector for the transceiver/radio end of the cable.  The cable is already prepped with 1/2 inch of each wire exposed, and 1/8 inch bare wire stripped, and solder tinned for easy attaching to your radio mating plug.           $5.99 each,  Order model 5DMX
This switcher enables you to leave your RASCAL GLX connected to the PC, and the CBLs connected to a separate transceiver accessory jacks.  Switch between your VHF or HF transceiver with just the flip of the  switch.  No cable swapping when you have the SW5 in line.  In addition, you can use this box to switch between the serial comports of your PC, or if you have only one serial comport, use the SX5 to switch between the RASCAL and another serial I/O device.  The SX5 is so versitle, it can be used as a monitor switchbox via the 15 pin I/O ports.  INCLUDES 1 RASCAL TO SW5 CABLE. Front   Back SO.., you need a 4 hole'r...                  No problem, BUX COMM has the solution !    You can use this box to switch between four serial comports of your PC(s), or if you have only one serial comport, use the SW5 to switch between the RASCAL and other serial I/O devices.  The SW5 is so versatile, it can be used as a monitor switchbox via the 15 pin PC monitor I/O ports.  INCLUDES 1, RASCAL GLX TO SW5 CABLE.    Switch positions are labeled "A,  B,  C,  &  D,"   Space is provided for you to label switch positions as you wish. Reg 44.95               Order SW5,   $ 24.95 each
RASCAL GLKit is the same as the RASCAL GLX, but in kit form.  We've had many requests for a kit version of the RASCAL GLX.  This RASCAL GLK (kit) has all the features of the RASCAL GLX, and is easily assembled and setup.  It's a FUN evening project you'll enjoy.  An experienced Amateur can have it on the air in less than an hour.   All parts, components, black case, cables, connectors, and detailed, step-by-step instructions, are included in the kit.  Choose one CBL (FREE) from the interface cable listing above.  Be sure you specify "CBL" number on order form with the RASCAL GLKIT !  Additional interface cables (CBL) are available at $12.95 each. RASCAL "KIT" 1 CBL is FREE   $29.95.   GLKIT       CLICK HERE for the RASCAL GLKit Page,
Our Lil Lite that we include with each RASCAL GLX. Additional lil lites are available at 99 cents each.  Batteries are included.  Perfect solution for finding the correct comport, or accessory jack on the dark sides of your PC or back of your transceiver.   Also doubles as a sturdy "key-ring."    LILITE

Our Shipping and Handling charges are based on the following table:

For shipments to destinations within the continental USA and CANADA
For Orders 0 to 2 pounds,        $7.90 added to total.
For Orders 2 to 5 pounds,        $9.90 added to total.
For Orders 5 to 10 pounds,      $11.90 added to total.
For Orders 10 to 20 pounds,    $15.90 added to total.
For Orders 20 to 55 pounds,    $28.90 added to total.

Foreign orders, 0 to 2 pounds, $15.90.   Sorry, due to lost and damage, No antennas shipped outside the continental USA

The NEW 2004 Amateur Radio CD ROM: is HERE;  NOW BIGGER THAN EVER!  More than 350 Megabytes of Packet Radio, PSK31-SSTV-RTTY-MFSK-PACKET, and hundreds more  interface diagrams, drawings, illustrations, tutorials, and MORE! CLICK HERE for more INFO about the Amateur Radio Operator's CD ROM for 2004. This CD contains MegaBytes of HAM Radio related articles, diagrams, illustrations, and drawings. Diagrams from 12 years of my Packet Users Notebook in CQ Magazine are included on this CD.   For Windows 95, 98, and WINNT This CD contains full versions of WinPSK and other 'freeware' programs for use with PSK31, Packet, SSTV, RTTY and more.    
$9.95   ORDER  2004CD  
This CD is included FREE with purchase of the Wired & Tested or Kit, RASCAL GLX & GLKit.

Digital Operating Frequencies for the HAM Radio Operator

A Primer for the new PSK31 user; CLICK HERE!

HAM Radio FREEWARE Software for Sound Card applications.

Sorry, we do not support soundcard program software.  For soundcard software & program support, contact the software vendor or author.

BUX Comm  1 BUX Drive; Evington,  VA 24550           FAX 434 525 7818

Wanna operate Packet Radio with the RASCAL..., Ralph Milnes, KC2RLM did an excellent job designing a web site that provides step-by-step instructions for running Sound Card Packet.  It illustrates the best methods to configure and use the AGW Packet Engine with various packet and APRS� programs, including: WinAPRS, APRSplus, UI-View, WinPack, AGWTerm, AGWMonitor, and AGWCluster.  If you would like to run packet with the RASCAL, go to Ralph's web site for the latest Packet Radio operation via the sound card and the RASCAL (Radio And Sound Card Adapter Link).

TNX es 73 ...   Email  Buck,  K4ABT

ALL MATERIAL, TEXT AND GRAPHICS ON THESE PAGES ARE � COPYRIGHT of, and by, G. E. "Buck" ROGERS Sr, K4ABT.
ALL RIGHTS ARE RESERVED, 1994-2004   Reproduction in any form must have the written permission of the author.

Shipping/Handling & warranty Return policy
  * "RASCAL"   is   Registered trademark �� of BUX Communications Corp (BUX CommCo �)   *(RASCAL�� "Radio And Sound Card Adapter Link")