Amateur Radio Base And Mobile, Antennas And Accessories

Base Station and Mobile:
Antennas & Accessories

* 1/4 wave on 2 meters * 2.5 dBi gain at 440 MHz. * Rated at 200 Watts * 12 ft of RG-58 cable with *PL-259 connector. * Magnet mount designed for winds of 100 mph * Overall height is 21 inches.		**Same as shown at left, but has BNC*** connector for use with hand-helds with BNC antenna input. $18.95 each ORDER VU-1510-"B"		5/8 wave antenna, 136 - 174 MHz NMO Base (Mount not included) 39 inches overall VSWR less than 1.5:1 200 Watts
$17.95 VU1510		$18.95 VU1510B		VH-1215 $16.95


5/8 wave antenna, 220-265 MHz NMO Base (Mount not included) VSWR less than 1.5:1 200 Watts 220-265 MHz version PM220 $21.95		$VU-1545		Recommended Mag Mount is AM-1045 B, NMO Mounts shown here. Get both, the VU1545 VHF/UHF (NMO) Antenna & the AM-1045B, 5 inch, Super Heavy-Duty Magnet Mount for $29.99
PM220 $21.95		17.95		BOTH 1545 &1045 for $29.95


Need a High Quality jumper from your transceiver to the linear? A HiQuality coax jumper for that transceiver Output to linear input! The connectors are Amphenol™ and coax is RG-8X by Belden. Hi Quality, Six ft. (9') jumper made using high quality components		*Remember the axiom; 'An ounce of prevention is worth a pound of cure.'* This lightning protector contains a modified spark gap that provides that ounce of prevention. . Remember, there is no substitute for a good earth ground, AC line surge, and spike protection. Where lightning is involved, we make no warranties. We offer the 7516 as a secondary lightning protector. Ground wire attached to wire lug. $ 4.99 ea Stock # 7516		Kit contains: 2 - Adhesive Pads 1 - Alcohol Surface Cleaning Swabs 1 - Trim Plate 1 - Shrink Tube REMOUNT KIT for all TG Series (Thru-Glass) Antennas.
$6.97 HIQ9JMPR		STORM SEASON is just around the corner. It pays to be prepared ! $ 4.99 ea		REMNTKIT 5.97

DIGITAL MULTIMETER Right Tech 9202. Here's a special deal on a digital multimeter. Ideal for the HAM Radio Operator, or technician. It has an LCD readout with 0.8" high digits. Features found on more expensive meters are standard on this DMM, they include: * A transistor and diode tester * An audible continuity checker. * Overload protection * Low battery indicator * Protective rubber case jacket. * Includes test leads and battery. MORE ! Ranges to: 1000 Volts DC, 750 Volts AC, 10 Amps DC, Resistance to 2,000,000 Ohms		Dual Band Magnet Mount Antenna 14.95 Low-cost, high quality, dual band antenna with magnetic mount. Ideal for commercial two-way and HAM Radio VHF/UHF FM mobile applications. 200 watt rated.		Use this mast-mounted bracket for 'fixed-station', field-day operating, apartment dwellers, or the mobile RV ops. With two of our mobile HF antennas you can have the best of both worlds. It is ou an ideal, single element, horizontal dipole (beam). Shown mounted on 1 & 1/4" mast. Dual antenna bracket only, antenna(s) Not Included. See BUX HF STIX below
$19.97 DMM		DBMM		DBLBRKT $14.95


	100 feet of RG-8U Low-Loss, Base-Station Coaxial Cable. It's low loss design and 95% or better shield makes it ideal for this application. PL-259 coax connectors are already installed on each end.		100 feet of RG-8U Low-Loss Base-Station Coaxial Cable. ORDER: RG8PL1C $49.97
BUX HF STIX BHF75M 75 METER 3/8" X 24 THREAD 8 feet long $16.95 BHF40M 40 METER 3/8" X 24 THREAD 8 feet long $16.95 BHF20M 20 METER 3/8" X 24 THREAD 8 feet long $16.95 BHF17M 17 METER 3/8" X 24 THREAD 8 feet long $16.95 BHF15M 15 METER 3/8" X 24 THREAD 8 feet long $16.95 BHF10M 10 METER 3/8" X 24 THREAD 8 feet long $16.95 BHF6M 6 METER 3/8" X 24 THREAD 5 feet long $16.95 Replacement, 48 inch Tips for above tuneable-tip antennas. TIP48, $2.95 → → These two-piece Mobile antennas consist of a hollow fiberglass base section approximately 1/2 inch diameter with the loading coil wound directly on the fiberglass and covered with shrink tubing. The chrome plated brass base fitting has 3/8 inch X 24 threads that fit the amateur standard 3/8" X 24 mobile mount. BUX stix HF antennas for Mobile and Base Applications: Power Rated at 250 Watts P E P; Typical 2:1.VSWR band width is: · 75 meter: 40 KHz. 40 Meter: 60 KHz. · 20 Meter: 150 KHz. 17 Meter: 175 KHz. · 15 Meter: 200 KHz. 12 Meter: 300 KHz. · 10 Meter: 500 KHz. 6 Meter: 1000 Khz. TUNING INSTRUCTIONS: Insert the whip into lower section ferrule about four inches (as shown at right) and tighten set screw. Assemble with fiberglass lower section (as shown at left). Install a VSWR meter at the transceiver and apply 10 to 25 watts of power. Adjust the VSWR meter and output frequency for lowest VSWR reading, indicating resonance. If resonant frequency is too high, loosen set screw and extend top whip until desired resonant frequency is found. If resonant frequency is too low, loosen set screw and adjust whip further into lower section. For best results, adjustments should be made in small increments. CAUTION: If required, cut off the bottom of the whip to ensure it does not extend down into the coil of the antenna. Failure to observe this precaution will cause heat damage and void any warranty. At resonance, VSWR should be 1.5:1 or less when properly matched. When tuning is complete, tighten set screws securely. NOTE: Bandwidth and VSWR will vary due to mounting location. If your installation has a VSWR over 1.5:1 at resonance, or you need to operate over a greater bandwidth a tuner may be required. DBLSPCL (without BUX UNUN (ONION) When the stations with the gain and power in their antennas are transmitting in the horizontal plane, then you should be meeting them in the same plane. Horizontal signals tend to follow the earths contour, and are easier to capture using a horizontally polarized antenna. See the BUX UNUN elsewhere on this page. By combining a pair (two) of the single band HF Mobile (loaded) tuneable-tip antennas above, you can have an ideal, single element, horizontal dipole (beam). This type antenna opens the world of HF communications for the apartment dweller, RV HAM, field-day operating, and a variety of other uses and applications. The packages described below include two antenna, the Double Antenna-Bracket (DBLBRKT), and mounting hardware. $ 39.97 DBLSPCL (without BUX UNUN (ONION) 75 Meters→, 40 Meters→, 20 Meters→, 17 Meters→, 15 Meters→, 10 Meters→, 6 Meters → BUX Double Combo "with" BUX ONION (UNUN). By combining a pair (two) of the single band HF Mobile (loaded) tuneable-tip antennas above, you can have an ideal, single element, horizontal dipole (beam). This type antenna opens the world of HF communications for the apartment dweller, RV HAM, field-day operating, and a variety of other uses and applications. The package described here include: two antenna, the Double-Bracket (DBLBRKT), mounting hardware, and BUX BALUN (UNUN). $AVE, BOTH, DPLSPCL & BUXUNUN, for only $ 54.97, ORDER, DBLCOMBO 75 Meters→, 40 Meters→, 20 Meters→, 17 Meters→, 15 Meters→, 10 Meters→ 6 Meters → *DUAL BAND, HIGH GAIN, BASE STATION ANTENNA, UVS-200* 6.7 db @ 2 meters, 8.2db 70cm. High Performance, High Gain, Dual Band, Base Station Antenna 5/8 wave, vertical stacked collinear design 2-5/8 elements on 2mt., 4-5/8 elements on 70cm. 6.7 db @ 2 meters and 8.2 db 70cm. Superior wideband performance Heavy duty fiberglass radome Durable, waterproof joints Mounting Hardware included Accepts standard PL-259 connector 200 Watt power rating Radiating element, 100 inches. DC ground, enclosed elements reduces terrestrial noise. ~~Reg $109.95~~ BUX COMM price, $57.97 UVS-200 VH-2201 VHF BASE & REPEATER Antenna. Frequency Range: 136-174 MHz Gain: 4.5dB VSWR less than 1.5:1 Power Rating: 200 watts Impedance: 50 Ohms Stainless Steel Radials SO-239 Input connector Radiating element Length 6 feet. Built to Commercial standards for base station installations, and rugged, mountain-top repeater applications. Mounting hardware and stainless-steel radials included. Ship wt, 5 Lb $47.97 VH-2201 UH-2401 UHF BASE & REPEATER Antenna Antenna Frequency Range: 430-490 MHz Gain: 6.5dB Power Rating: 200 watts Impedance: 50 Ohms Stainless Steel Radials SO-239 Input connector Radiating element length 5 feet. Built to Commercial standards for base station installations, and rugged, mountain-top repeater applications. Mounting hardware and stainless-steel radials included. Ship wt, 5 Lb $47.97 UH-2401 "Vertical" Six Meter Ground Plane All mounting hardware and assembly instructions are included. Also includes cutting chart for exact frequency measurements. *Solid Hard-Drawn Aluminum* GP6M $49.95 Fiber Glass FGP6M $49.95 VHF and UHF 'Cross-Needle' High Performance, SWR & POWER Meter. For the serious VHF/UHF operator, here is a 140 to 160 MHz & 440 to 480 MHz, VSWR and POWER meter with; 10 - 100 - 1000 watt scales. SWR-6 $69.95 SWR & WATT METER 100 watt & 10 watt level switch This is a handy, compact meter designed for the amateur radio operator. Test antenna performance and transmitter operation, 1.7 to 50 MHz. May also be used as a RF field strength meter and to check QRP. SWR-3, $19.95 SWR: 1:1 to 1:3; RF Power: 0.5~10W; Accuracy: =SWR: +- 5% Power: +- 10%; Impedance: 52 W, Meter Sens. 200uA Freq. Range 1.7 to 30MHz QRP, SWR & POWER Meter, (0.5 to 10 watts) Freq. Range 1.7 to 30MHz SWR-2T, $12.99 Important Information; WHY USE A 4:1 BALUN Krusty Olde Kurt is now going to repeat himself. Why? Because the same question keeps coming up over and over. And he wants everyone to get it right. "I'm feeding my dipole with 600-ohm line. At the station end I need a balun to convert to 50-ohm coax. I need a 12:1 balun, right?" *Wrong!* A 4:1 balun* would be better. Why is that?* If your dipole is up, let's say, 35 feet then on 80 meters it will probably have a resistance at resonance of about 40 ohms. The actual resistance depends on the height above ground in wavelengths. If the dipole is 40 Ohms then what do you see at the transmitter end of your 600 ohm line? If the line is a half-wave long (120 ft on 80 Meters) you'll see 40 ohms. Remember, a half-wave line repeats what it sees at the other end. But if it is a quarter-wave long you'll see 8500 Ohms! At other line lengths you'll see impedances somewhere between these two extremes. So you are not going to see 600 ohms at the end of your 600-ohm line. That only happens if you have a 600-ohm antenna hooked onto it. With such a variation in impedance at the transmitter end of the line there is no one balun transformer that will match it. Most of the time the impedance will be above the 50 Ohms of your coax so a high impedance balun would be desirable. Unfortunately high impedance baluns don't work well when not matched. Experience has shown that 4:1 baluns work best in this service. They are more rugged and will take bad mismatches especially if they are wound on an iron powder core. So stop searching for that 12:1 balun. Use a 4:l BALUN and your system will work great. You can read Kurt N. Sterba “AERIALS” column in World Radio Magazine. BUX ONION $19.95 "Decoupling Transformer" BUX UN UN De-Coupling transformer, has SO-239 (female) input connector and output connector is 1 ft Mini 8 cable with PL-259 (male). BUX ONION is an UNbalanced to UNbalance (UN-UN) decoupling transformer designed to be used by the Apartment dweller or the RV ops. It is also used with the DBLSPCL antenna. High RF currents traveling along the coax feed-line shield can cause high VSWR. This decoupling transformer prevents RF currents from traveling down the outer shield of the coax. The input connector is an SO239 (female) and the output connector is a PL259 (male). BUX ONION $19.95 BONUS SPECIAL ! Buy either of our 4:1 HD *⁭ or our 1:1 HD ↓ BALUNs and receive "FREE," three of our "super, high-dielectric" White, TyNyte, Insulators* 4:1 1.5 Kw Balun, BUX BALUN 41HD *Toroid design, wound with teflon covered, silver plated wire. Heavy-Duty, construction, on powered iron cores. o 50 ohm, SO-239 unbalanced input o Heavy duty Hardened Brass, Balanced output connectors o 1.8 to 50 MHz o Toroid (Voltage) design o Heavy Duty, Lightweight construction o Sealed against moisture 41HD $19.95** 1:1, 1.5kw Balun, BUX BALUN 11HD $19.95 o 50 ohm, SO-239 unbalanced input o Balanced output o 1.8 to 50 MHz o Toroid (Current) design o Heavy Duty, Lightweight construction o Sealed against moisture 11HD $19.95 This is our BUX COMM High-Performance "HAMMER," built to endure some harsh treatment, and designed to cope with a "wholesome" kilowatt... or two.10" x 4" 4:1 Hi-Power Wt. 1.5 LBs UNBALANCED 50 OHM INPUT, BALANCED 200 OHM OUTPUT, 160 thru 6 Meters. HEAVY DUTY TOROID MADE OF POWERED IRON, FOR LOW PERMEABILITY 4:1 High Performance, Heavy Duty, 2 KW Balun (if SWR is less than 2:1)* CW/SSB duty-cycles only. SSB/CW Power @ 3.5 MHz* >2 kW if SWR is less than 3:1, Not rated for RTTY & AM.* Will not saturate at Amateur Radio Power Levels 3KBBB $ 39.95 With an increase in local noise sources and the increasing attractiveness of long wire and dipole antennas, coax cable has become the antenna feed line of choice for most radio users and operators. Given that the impedance of most commonly available coax is either 50 or 72 ohms and since many wire antennas present an impedance of 200 to 600 ohms or more at the feed point, direct connection of the coax to wire antennas hits us with a significant signal loss due to the antenna impedance mismatch. Having realized this set of circumstances in the receiver and SWL arena, we're introducing a new approach to defeat the noise and impedance mismatch problems in our receive antennas by designing this new RxBALUN™. Our RxBALUN™ bridges the impedance gap, and enables an unbalance to balanced match between the antenna and our receivers. These features provide more signal transfer from the antenna to your receiver. Our RxBALUN will accommodate the SWL and QRP Operator. In addition, this RxBALUN may be employed as an antenna balun for both transmit and receive between the antenna and low powered transceivers running up to 200 watts. For input and output connectors, we use only the best Silver plated, Teflon®™ insulated, SO239 connectors. Max Power 250 watts 14.95 RxBALUN Stainless eyebolt is inserted into Tenyte "Center Insulator" The "Center Insulator" is used to suspend the center of a Dipole, Windom, or other wire type antenna from tower, tree, or support structure. 1.99 Stock# CIA Center Insulator and two end insulators 3.99 Order CIAX3 For the apartment dweller, you can now hang the 20 meter doublet in the attic. I've QSO'd with stations all over the world with the 33 ft dipole in the attic of my garage. One insulator at the center, and one each end. It's great for other HF WINDOM and or dipole antenna. Dielectric strength is better than the old ceramic insulators, but without susceptibility to cracking or breakage under impact or extreme temperature changes. Package of 3, $2.99 Antenna Insulators Package of 10, Insulators $8.99, ANTINSLX10 A METHOD TO HANG YOUR BALUN. CLICK ON THUMBNAIL AT RIGHT TO VIEW FULL SIZE DRAWING. Dipole and inverted-Vee antennas are commonly "balanced" at the feed points. Coaxial feed lines are "unbalanced" by design personality (thus the name BALUN). This BALANCED, to UNBALANCE marriage can only be performed by using a BALUN. A BALUN should always be used when feeding wire antennas with coax to make certain characteristic antenna performance and optimum transfer of RF energy to the antenna complete. When coax is used to feed antennas without the benefit of a BALUN, current flows on the shield of the coaxial feed line . This coaxial shield current can produce a "Hot HAM shack," This can result in nasty R.F. injury from the microphone to lips, hand key to fingers, etc., and is often more pronounced at certain frequencies. Coax cable shield currents can also cause damage to your HAM gear. TVI, RFI, telephone and even wild VSWR indications can result from these shield currents. In 85% of antenna projects that displayed these problems, when a BALUN is added to the coaxial line or near the antenna feed point, these problems were diminished or completely eliminated. At BUX COMM, We don't cut corners! The components used in the manufacture of our BALUNs are from top quality components, beginning with the Silver Plated SO239 connectors and center insulator made of teflon™(E.I Dupont), and the center pin is hard-drawn brass, with gold flash. The wire we wind the ferrite donut with, is heavy-duty, silver flashed wire, with teflon™ insulation, which will handle RF voltages above 5000 volts, and temperatures above 2000 degrees. The binding posts are heavy-duty, tempered brass, with end holes and side-thru holes to accommodate either type loop-thru connection. A double-shoulder brass capture nut is used to add a secure bite and improve electrical connections to the wire . In addition, these Antenna connection points are clearly identified with "RED" and "BLACK" rings to denote the "hot" and "cold" terminals... just in case you want to favor the highest or longest side of your antenna. The Duplexer shown here is the ideal companion for our Dual-Band, Base Antennas ! HF and VHF/UHF Antenna Duplexer (Indoor use) Frequency: (Port 1) 1.3 - 225 MHz, (Port 2) 350 - 540 MHz Power: 500 W 1.3 - 35 MHz, 300 W 50 - 540 MHz Insertion Loss: <0.2 dB Isolation: 60 dB; VSWR: < 1.2:1 Combine HF/6m/2m output (Port 1) and your UHF output from your transceiver and send to one antenna. $34.95 Order DU-500 Specifications: Frequency Range: Up to, and including 600 MHz VSWR: Below 1.2:1 Power Rating: 1.5 kW peak 1kW continuous Impedance: 50 Ohms Insertion loss: Less than 0.2 dB. Port Isolation: Better than 50 dB. Port connectors: SO-239 One IN, Two Out, and May be configured Two IN, One Out. 2 Position Coax Switch CX-201 $19.95 GOLD LINE 2 POSITION Antenna Switch Switch between Beam, and HF wire antennas, or between VHF/UHF and HF Beams. RATED AT 1 kW. GL1048 $ 11.95 Antenna Coax Switch; 1 IN, 3 Out, in Metal case. Antenna Coax Switch; One IN, Three Out, or Three IN, and One OUT, 50 Ohm impedance, 3 port to 1 port Antenna Switch. Rated at 1 KW, SO-239 ports, mounted in metal case. CX3 $9.95 HandHeld "HR-9" Duckie Frequency: 144 - 148 MHz SWR: Less than 1.5:1 Connector: BNC Male Length: 4 inches, or 105/mm 9.95 HR-9 HR-601VU VHF & UHF* Antenna Dual-Band, HandHeld antenna, with SMA male connector for use with late model transceivers 12.95 HR-601VU HR-601V is for VHF only handheld transceivers. Frequency: 144-148 MHz VSWR: Less than 1.8:1 Whip is Shape/Memory Alloy Connector: SMA Male 10.95 HR-601V NMO Mount RAIN CAP. Used to cover the NMO mount when not in use. Comes in basic gloss black. YES, they are in Stock! The NMO cover with built-in "0-Ring" seal. .99 ea, Order NMO5 HOLE PLUGS Drilled the hole in the wrong place? Removed an old base-loaded antenna; This black rubber plug is inserted into the hole to seal from moisture. It can be painted to blend color. The profile is about 1/8 inch high when inserted, Plug for 3/8" hole .99 Plug for 1/2" hole .99 Plug for 5/8" hole .99 Plug for 3/4" hole .99 Plug for 7/8" hole .99 Plug for 1" hole .99 This NMO Hole Mount will fit into a 3/8" hole, or use the adapter (included) to adapt it to a 3/4" hole. The BUX CommCo NMOH is supplied with 17 ft of 98% shielded RG-58 cable terminated into a PL-259 UHF connector. Cables are attached at right angles to the mount. Mounts also include a built-in seal around the mounting hole to protect from moisture. AM-207B $8.95 Trunk Lip, NMO Mount, model AM-209 is a trunk-lip mount supplied with 14 ft of RG-58 cable, a PL-259, and the industry standard NMO mount. The AM-209 mounts on a standard trunk-lip and comes with 14ft of cable terminated in a PL-259. AM-209 $11.95 NMO mount only. For virgin installation when cable is already in place. No cable, only the NMO mount. Hardened Brass. $4.95 NMO-2 ANTENNA ADAPTER 3/8"x24 thread base antenna to NMO Mount When you don't care to drill another hole for that whip, or new antenna, this heavy-duty adapter mates a 3/8"x24 thread antenna base to an NMO mount. Also includes "O" ring-to-body, seal to prevent moisture oxidation. NMO-6 $8.95 NMO to SO239 Antenna Adapter When you don't care to drill another hole for that whip, or new antenna, this heavy-duty adapter mates a SO-239 (PL259 type) antenna base to an NMO mount. Also includes "O" ring-to-body, seal to prevent moisture oxidation . $8.95 NMO8 Trunk Lip Mount (ABS) with steel lip clamp and dual set-screws. Accepts antennas with standard 3/8" X 24 thread base. Pre-wired with 17" of RG/58 to BNC Connector. Black rubber paint protector, see photo. Includes a PL-259 connector $7.97 TLMPL259 "The Adapter" is the best way to describe it ! Our number one seller when it comes to antenna adapters. $ 2.99 each Order 7060 BNC male to UHF Female $2.99 ea WINDOW CLIP for HT or SCANNER ANTENNA SMA window antenna clip $10.95 AM 800 BNC window antenna clip $11.95 AM 801B SMA or BNC "HAT" Clip-on Mount SMA $10.95, AM 550 BNC Hat Clip $11.95 AM 551 Your BUX BALUN is warranted against defects in components or construction for a period of three (3) months from date of purchase. Our warranty does not cover damage due to misuse, abuse, or nonessential operation outside the specifications of the BUX BALUN. This warranty applies only to the original purchaser. A copy of the receipt showing the purchaser’s name and the date of purchase must accompany BALUN's returned for warranty service or replacement. All returns must be shipped prepaid. Should there arise a requirement to return your BUX BALUN for service, carefully wrap and package it. We will re-use your carton to return the BUX BALUN to you. Be sure to include your return address. Include a full description of the problem, along with your name, address, phone number and/or e-mail address. Repairs average approximately 3 to 4 days. QUAD MAGNET, Antenna Mount. Available in; Triple Chrome Plate, or Basic Black. You asked for strength in a super mobile antenna mount, and WE DELIVERED ! Features 4, five inch Heavy-Duty magnets, equally spaced on a Heavy Duty, 1/4" thick, hard-drawn metal frame. The BUX4MM is prewired with 3/8" X 24 threaded (standard) Mount, and PL259 connector. Accepts 3/8 X 24 antennas $44.97 BUX4MMC "chrome" $44.97 BUX4MMB "Black"


Dual Antenna Mount accepts 3/8"X24 thread antenna bases.				"Super" Magnet 95 lb. pull strength. This powerful 5 inch magnet comes with 17 feet RG 58 coax with PL-259 connector. It has the standard antenna 3/8" X 24 female threads. A strong magnet mount for HAM type mobile antennas. Prewired with 17" RG58 cable PL-259 connector
$11.95 Order DAM		DBLBRKT $14.95		5" version MA1035 $14.95 3 " version MA1034 $12.95

You've heard about it, and here it is; The GOLDEN Super "ROD" antenna Six section, telescoping "rod" antenna for hand-held transceivers VSWR: Less than, 1.5:1 Connector: BNC male Length: 108cm extended (48") and 26.5cm collasped. approx. ~~$12.95~~		MARINE ANTENNA No Ground VHF Marine Antenna.Ideal for bass boats, small run-about, and sail boats. 3 dB gain effectively doubles your transmitter's effective radiated power. Great for auto's with fiberglass body's or for wood craft - no ground required. Low profile 36" height is ideal for top mast mounts on sailboats or for use on bass and ski boats or run-a-bouts where long antennas might hamper operations. Comes complete with stainless steel "L" type mounting bracket and preassembled 15' coax cable fitted with PL259 connectors.		Our MoBALUN is also ideal for marine antenna installations. When you hear those strong HF mobile signals, here's one reason they stand out from the rest. By installing the BUX MoBalun near the input to your antenna, you deliver more RF energy to the antenna. At the same time, the BUX MoBalun prevents RF from traveling back along the shield (high SWR) of your coax. High power rating, Low-permeability toroid, with Internal composition fiber-glass to prevent vibration during mobile operation. For input and output connectors, we use only the best Silver plated, Teflon insulated, SO239 connectors. 500 watts.
HR-22 $7.99		$37.97		19.95 MOBALUN


3 inch, NMO Magnetic antenna mount. Black finish, and a good "grabber" to a smooth, flat, metal surface. A good companion mount for the DB-2. Black finish, and a good "grabber" to a smooth, flat, metal surface. A good companion mount for the UV325 shown near top of this page.		5 inch, NMO Magnetic antenna mount. Black finish, and a good "grabber" to a smooth, flat, metal surface. A good companion mount for the DB-2 shown on this page. This is a Larger, 5 inch heavy duty Magnet, w/coax and connector. 5 inch, NMO Magnetic antenna mount. Black finish, and a good "grabber" to a smooth, flat, metal surface. A good companion mount for the UV325 shown near top of this page.		DB-2 Dual Band mobile antenna for 144 & 430 MHz VSWR: Less than, 1.5:1 Connector: NMO base. Length: 39cm or 15.5 in. approx. ADD the NMO, 5 inch magnet mount for a durable, dual-band mobile antenna combo
AM-1043B 3.5 Inch, $14.95		AM-1045B 5 Inch $17.95		DB2 $14.95



AM-101. Magnetic SO239 Mount 3.5" strong magnet mount with black plastic finish. 17' RG58 coax with PL-259.
12.99

Both, DB-2 and 1045B for only: $29.95		Great for Apartment Dwellers, RV, pickup truck-bed rail, or Bumper installations. Rail or Bumper Heavy-Duty Antenna Mount Length of this bar is 12 inches, and width is 2 inches. The bar is almost one quarter inch thick. Mounting screws and 3/8" X 24 standard thread, stud mount are included. By using our KD-3 Kwik-Disconnect, you can quickly change bands, or make your antenna setup into a "stealth" installation		Shown here is our T-BAR TRUX Stake hole mount. This one is for the serious HAM. The T-Bar mount is constructed of stainless steel and locates the antenna directly over the truck bed rail. Expandable rubber base locks mount for secure fit when tightened. Great for our HF stix and out heavy-duty whips. Fits most pickup truck models and brands. Heavy Duty Right angle SO239 and 3/8" x 24 threaded stud, included,
$29.95 DB2-45		$14.95 order BUXTRUXHD		TSTAKMNT $ 24.99

Right Angle SM1L Mount Right angle stud mount with SO239 coaxial cable connector and a 3/8-24 threaded antenna socket. Great for those cramped areas. Reg ~~11.95~~, BUX COMM Price: $8.88		Pick-Up Truck, Flat-BAR, STAKE HOLE Mount		Adjustable Bumper Mount with 3/8"x24 thread SM-1, and SO239 (PL259) input. Both may be used on hatch-back lid-lip, trunk-lip, bumper & hood.
$ 8.88 each		$19.95		442 S $16.95


BUMPER MOUNT with SO239 input connector, accepts PL259. $9.95 Order 422-S
422-S $9.95		Ball Mount with SO-239 (female) connector, AM601S $9.95		Ball Mount with terminal lug connection, AM601L $9.95


Heavy Duty Spring for Whips up to 102 inches.		Often called the mobile antenna, Kwik-Disconnect This Mobile Antenna Adapter... is a 'SNAP' to change antennas or bands in a matter of seconds		Set of five (5) Kwik-Connect Antenna adapters and snap-on stud. Make changing mobile antennas a 'SNAP!' with a set of 5 ''Kwik Disconnect'' adapters.
S55S $8.95		KD-3 $5.95		KD-5 $15.95 Set of 5.

The EZ230 enables you to fold your mobile antenna over to a low-profile, horizontal position. This prone position allows entry into low-overhead garages, and prevents damage to the antenna. A "must" for the mobile HAM. Both sleeve and threaded section are standard 3/8" X 24 threads.		Dual Band whip antenna for 144 & 440 MHz VSWR: Less than, 1.5:1 Connector: 3/8" x 24 threads dual-band mobile antenna. As shown, antenna only, requires 3/8 X 24 base.		Lost the ferrule that holds your whip-tip atop your BUX-STIX antenna? Here is the replacement complete with set-screw. Threads are standard 3/8 x 24.
EZ230 $9.95		14440WP $3.97		TIPFERL $3.97


Order 7518-1 (One inch ) ^$ 1.79 ea. 10 for ^$15.50 Order 7518-2 (Two inches) ^$ 2.95 ea. 10 for ^$ 24.50 Order 7518-3 (Three inches) ^$ 3.69 ea. 10 for ^$ 32.50 Order 7518-4 (Four inches) ^$ 3.95 ea. 10 for ^$ 34.50 Order 7518-6 (Six inches) ^$ 4.95 ea. 10 for ^$ 44.50 Order 7518-8 (Eight inches) ^$ 8.95 ea. 10 for ^$ 82.50 Order 7518-10 (Ten inches) ^$ 10.95ea. 10 for ^$ 99.50 Order 7518-12 (Twelve inches) ^$12.95ea. 10 for ^$ 114.50 Heavy Duty 1" Nuts for the above bulkhead connectors. 2/.99 cents HDM1-NUT 10 for $ 3.99 50 Ohm impedance, 3 ft, 6 ft, 9 ft, 12 ft, & 18 feet. These jumpers are made from high quality, low-loss, coax cable with PL-259 connectors installed. Three ft. (3') ORDER No. 8X3-PLPL $3.99 Six ft. (6') ORDER No. 8X6-PLPL $4.99 Nine ft. (9') ORDER No. 8X9-PLPL $5.99 Twelve ft. (12') ORDER No. 8X12-PLPL $7.99 Eighteen ft. (18')ORDER No. 8X18-PLPL $8.99 Shop Online or call our Order Line Monday thru Friday (except holidays) 1-434-534-8873 Customer Service [email protected] *Download our* *Catalog* As of December 10th our brand new Winter 04/05 catalog is available in PDF FORMAT Bumper Mount includes (SM1) SO-239 UHF connector to 3/8x24 antenna base (see SM1, this page). $7.95 ea Included→ AM370RS Insulated Antenna Stud Mount with SO-239 female connector for easy connecting with PL-259 fitting. Threaded for standard 3/8 X 24 mobile antenna use. $ 2.99 SM1 10 for 17.95 Mirror-Mount with insulated stud, for 3/8 X 24 thread medium duty mobile antenna mounting. AM304S $6.95 Each Replacement, Hardened, Nylon, Heavy duty, Shoulder washer insulators, same as shoulder washers in SM1 Stud-Mount. 4 for 99¢ SM1SW