|
Trailer Hitch Mount
with 7/8" hole for mounting with trailer-hitch ball, bolt.
for antennas with 3/8" X 24 (standard) antenna base. Stainless steel
with SO239 coax fitting to receive PL259 coax connector.
Also accepts the BUX HF STIX shown above.
Stock number THM1
$ 11.95 
|
$ 17.95
|
|
NOTE: The
UHFH239 (SO239) mount at
right,→
is easy to replace the NMO connector in the above stake-hole mount. |
|
Ideal for: Campers. RV's, trailers, boats, and fender
mounting where small metal ground plane area is available. $3.95 each
Order UHFH239
|
$19.95
Pick-Up Truck, Flat-BAR, STAKE HOLE Mount with SM1 for 3/8"
x 24 thread base antennas.
|
← |
|
MOBILE KING, Antenna UNUN
For bottom fed, and screw-driver antennas.
1.8 MHz to 50 MHz
Master Match
MOBILE KING "Big
Talker" Mobile UNUN
o SO-239 connectors, in & out,
o 50 ohm, SO-239 unbalanced input.
o
12 ohm, SO-239 output, SO-239 connector.
o 1.8 to 50 MHz
o
Ferrite Broadband toroid design
o Heavy Duty, Lightweight construction
o FREE 3ft RG8X coax with PL259,
included
o Sealed against moisture
Order SDAB UNUN
$19.95
|
 Keep
your Mobile RF Power at your antenna.
When operating mobile, every watt your
transceiver sends is valuable. Add the BUX MoBALUN and be one of the
mobile signals that stand out from the rest. By installing the BUX
MoBalun near the input to your antenna, you deliver more RF energy to the
antenna.
At the same time, the BUX MoBalun
prevents RF from traveling back along the shield of your coax as
(high SWR), therefore more power is transmitted as useful RF energy.
High power rating, Low-permeability
toroid, with Internal fiber-glass composition to prevent unnecessary
vibration during mobile operation.
For input and output connectors, we use
only the best Silver plated, Teflon®™
insulated, SO239 connectors, and Amphenol PL259, with 20
inches of RG8X to connect to the input of your antenna.
Power
rating of our BUX MoBALUN is 1000 watts.
Our MoBALUN is also ideal for marine antenna installations.
$17.95 MOBALUN
Our MoBALUN is also available with binding-post "terminals."
ORDER MOBALUN-T
$ 19.95
Teflon ®™
E I DuPont corp.
Amphenol
®™
TYCO Corp.
|
*
1/4 wave on 2 meters
* 2.5 dBi gain at 440 MHz.
* Rated at 200 Watts
* 12 ft of RG-58 cable with *PL-259
connector.
* Magnet mount designed for winds of 100 mph
* Overall height is 21 inches. |
|
Same
as shown at left, but has *BNC connector for use with hand-helds with BNC
antenna input. $18.95 each ORDER
VU-1510-"B" |
|
 5/8
wave antenna,
136 - 174 MHz
NMO Base
(Mount not included)
39 inches overall
VSWR less than 1.5:1
200 Watts |
|
$17.95 VU1510 |
|
$18.95 VU1510B |
|
VH-1215
$16.95
|
|
|
5/8
wave antenna,
220-265 MHz
NMO Base
(Mount not included)
VSWR less than 1.5:1
200 Watts
220-265 MHz
version PM220
$21.95 |
|
 
$VU-1545 |
|
 Recommended
Mag Mount is AM-1045 B, NMO Mounts shown here. Get both, the VU1545
VHF/UHF (NMO) Antenna & the AM-1045B, 5 inch, Super Heavy-Duty
Magnet Mount for $29.99
|
|
PM220
$21.95 |
|
17.95 |
|
BOTH 1545 &1045
for $29.95 |
| |
|
BLACK CABLE TIES
- 100pcs
.99 Pk of 100
Colour: BLACK (UV Resistant)
Dimensions (A x B): 98 x 2.5mm
Quantity: 100 pcs per/Pak
Material: polyamide (nylon 6.6) as specified in MIL-S-23190
self-extinguishing.
Temperature: -40°F to 230°F
Tensile strength = 18 pounds
A = 4 inches
.99 / Pak of 100
Order : KTFB3
|
|
 |
|
 140
- 170 MHz VHF
Economy Mag Mount Antenna.
Order 2MMM 11.95
|
 Need a High Quality jumper from your transceiver to the linear? A
HiQuality coax jumper for that transceiver Output to linear input! The
connectors are Amphenol™ and coax is RG-8X by Belden. Hi Quality,
Six ft. (9') jumper made using high quality components
$6.97
HIQ9JMPR
|
|
Remember the axiom;
'An ounce of prevention is worth a pound of cure.'
This lightning protector contains a modified
spark gap that provides that ounce of prevention. . Remember, there is no
substitute for a good earth ground, AC line surge, and spike protection.
Where lightning is involved, we make no warranties. We offer the 7516 as a
secondary lightning protector. Ground wire attached to wire lug.
$ 4.99 ea Stock # 7516
STORM SEASON is just around the
corner. It pays to be prepared !
$ 4.99 ea
|
|
Kit contains:
2 - Adhesive Pads
1 - Alcohol Surface Cleaning Swabs
1 - Trim Plate
1 - Shrink Tube
REMOUNT KIT for all TG Series (Thru-Glass) Antennas.
REMNTKIT 5.97
|
| |
|
$ 6.95
each
|
|
Dual Band Magnet Mount Antenna 14.95 Low-cost, high quality, dual band
antenna with magnetic mount. Ideal for commercial two-way and HAM Radio
VHF/UHF FM mobile applications.
Power Rating, 200 watts.
14.95 DBMM
|
|
Ideal for: Campers. RV's, trailers, boats, and fender
mounting where small metal ground plane area is available. $3.95 each
Order UHFH239
|
|
BLACK CABLE TIES - 100pcs
.99 Pk of 100
Colour: BLACK (UV Resistant)
Dimensions (A x B): 98 x 2.5mm
Quantity: 100 pcs per/Pak
Material: polyamide (nylon 6.6) as specified in MIL-S-23190
self-extinguishing.
Temperature: -40°F to 230°F
Tensile strength = 18 pounds
A = 4 inches |
|
|
|
.99 / Pak of 100
Order : KTFB3
|
 |
100 feet of RG-8U
 Low-Loss,
Base-Station Coaxial Cable. It's low loss design and 97% or better shield
makes it ideal for this application. GOLD
PL-259 coax connectors are installed on each end |
50 feet of
RG-8U with 97% shielding, Low-Loss, Base-Station Coaxial Cable.
ORDER: RG8PL1L
$39.97
Both ends are fitted with "GOLD" plated PL259/7506
connectors !
100 feet of RG-8U, with 97% shielding,
Low-Loss Base-Station Coaxial Cable.
ORDER:
RG8PL1C
$59.97
|
50 Ohm impedance,
3ft, 6ft, 9ft, 12ft,18ft, 50ft &
100 feet.
These jumpers are made from high quality, low-loss,
Belden
coax cable with Amphenol PL-259 connectors installed.
 Three ft. (3') ORDER No. 8X3-PLPL $3.99
Six ft. (6') ORDER No. 8X6-PLPL $4.99
Nine ft. (9') ORDER No. 8X9-PLPL $5.99
Twelve ft. (12') ORDER No. 8X12-PLPL $7.99
Eighteen ft. (18')ORDER No. 8X18-PLPL $8.99
Fifty ft. (50') ORDER No.
RG8X50PLPL $22.95
One Hundred ft. (100')
ORDER No. RG8X100PLPL
$34.95
|
|
BUX HF STIX
 BHF75M
75 METER 3/8" X 24 THREAD 8 feet long $16.95
BHF40M 40 METER 3/8" X 24 THREAD 8 feet long
$16.95
BHF20M 20 METER 3/8" X 24 THREAD 8 feet long
$16.95
BHF17M 17 METER 3/8" X 24 THREAD 8 feet long
$16.95
BHF15M 15 METER 3/8" X 24 THREAD 8 feet long $16.95
BHF10M 10 METER 3/8" X 24 THREAD 8 feet long $16.95
BHF6M 6 METER 3/8" X 24 THREAD 5 feet long
$16.95
These two-piece Mobile antennas consist of
a hollow fiberglass base section approximately 1/2 inch diameter with the
loading coil wound directly on the fiberglass and covered with shrink
tubing. The chrome plated brass base fitting has 3/8 inch X 24
threads that fit the amateur standard 3/8" X 24 mobile mount.
Replacement,
48 inch Tips for above tuneable-tip
antennas. TIP48, $2.95
→
→
BUX stix
HF antennas
for Mobile and Base
Applications:
Power Rated at 250 Watts P E P;
Typical 2:1.VSWR band width is:
·
75 meter: 40 KHz. 40
Meter: 60 KHz.
·
20 Meter: 150 KHz. 17
Meter: 175 KHz.
·
15 Meter: 200 KHz. 12
Meter: 300 KHz.
·
10 Meter: 500 KHz. 6
Meter: 1000 Khz.
TUNING
INSTRUCTIONS:
Insert the whip into lower section ferrule about four inches (as shown at
right) and tighten set screw. Assemble with fiberglass lower section (as
shown at left). Install a VSWR meter at the transceiver and apply 10 to 25
watts of power. Adjust the VSWR meter and output frequency for lowest VSWR
reading, indicating resonance. If resonant frequency is too high,
loosen set screw and extend top whip until desired resonant frequency is
found. If resonant frequency is too low, loosen set screw and adjust
whip further into lower section. For best results, adjustments
should be made in small increments.
CAUTION: If required, cut off the bottom of
the whip to ensure it does not extend down into the coil of the antenna.
Failure to observe this precaution will cause heat damage and void any
warranty. At resonance, VSWR should be 1.5:1 or less when properly
matched. When tuning is complete, tighten set screws securely. NOTE:
Bandwidth and VSWR will vary due to mounting location. If your
installation has a VSWR over 1.5:1 at resonance, or you need to operate
over a greater bandwidth a tuner may be required.
|
|
 Thru-Glass
Scanner antenna. Covers 20 MHz to 1200 MHz.
Supplied with 14 ft of coax with connector and mounting materials.
Installation instructions and recommended mounting location.
9.95 Order SCANT
|
|
A
professional meter for measuring VSWR and POWER for a wide frequency
range:
 The HP500 has a dual instrument window and positive
press switches. Technical Specifications:
* Frequency Range 3 - 200 MHz
* Impedance 50 or 75 ohms. Accuracy ± 10%
* Power Measurements 10 W / 100 W / 1000 W
* Wide band cover
for both SWR and Power 3-200MHz.
* Power up to 2Kw PEP plus 50-75 ohm switching.
ZETAGI Order Cat # HP-500
WAS $79.95 NOW SALE priced
$ 64.95
 VHF and UHF 'Cross-Needle' High
Performance, SWR & POWER Meter.
For the serious VHF/UHF operator, here is a 140 to 160 MHz & 440 to 480
MHz, VSWR and POWER meter with; 10 - 100 - 1000 watt scales.
SWR-6 $69.95
 SWR
& WATT METER 100 watt & 10 watt level switch This is a handy, compact
meter designed for the amateur radio operator. Test antenna performance
and transmitter operation, 1.7 to 50 MHz. May also be used as a RF field
strength meter and to check QRP.
SWR-3, $19.95
 SWR:
1:1 to 1:3; RF Power: 0.5~10W;
Accuracy: =SWR: +- 5%
Power: +- 10%; Impedance: 52
W,
Meter Sens. 200uA
Freq. Range 1.7 to 30MHz
QRP, SWR & POWER Meter, (0.5 to 10
watts) Freq. Range 1.7 to 30MHz
SWR-2T, $12.99
|
|
The
Duplexer shown here is the ideal companion for our Dual-Band, Base
Antennas ! HF and VHF/UHF Antenna Duplexer (Indoor use)
Frequency: (Port 1) 1.3 - 225 MHz, (Port 2) 350 - 540 MHz
Power: 500 W 1.3 - 35 MHz, 300 W 50 - 540 MHz
Insertion Loss: <0.2 dB Isolation: 60 dB; VSWR: < 1.2:1
Combine HF/6m/2m output (Port 1) and your UHF output
from your transceiver and send to one antenna.
$ 34.95
Order DU-500
|
|
 Specifications:
Frequency Range: Up to, and including 600 MHz
VSWR: Below 1.2:1
Power Rating: 1.5 kW peak 1kW continuous
Impedance: 50 Ohms
Insertion loss: Less than 0.2 dB.
Port Isolation: Better than 50 dB.
Port connectors: SO-239
One IN, Two Out, and
May be configured Two IN, One Out.
2 Position Coax Switch
CX-201
$19.95
|
|
 GOLD
LINE 2 POSITION Antenna Switch
Switch between Beam, and HF wire antennas, or between VHF/UHF and HF
Beams. RATED AT 1 kW.
GL1048 $
9.95
 Antenna
Coax Switch; 1 IN, 3 Out, in Metal case.
Antenna Coax Switch; One IN, Three Out, or Three IN, and One OUT, 50 Ohm
impedance, 3 port to 1 port Antenna Switch. Rated at 1 KW, SO-239 ports,
mounted in metal case.
CX3 $9.95
|
HandHeld
"HR-9" Duckie
Frequency: 144 - 148 MHz
SWR: Less than
1.5:1
Connector:
BNC Male
Length: 4
inches, or 105/mm
9.95 HR-9
 HR-601VU
VHF & UHF Antenna
Dual-Band,
HandHeld antenna, with SMA male connector for use with late model
transceivers
12.95 HR-601VU
|
|
 HR-601V
is for VHF only handheld transceivers.
Frequency: 144-148 MHz
VSWR: Less than 1.8:1
Whip is Shape/Memory Alloy
Connector: SMA Male
10.95 HR-601V
|
WINDOW CLIP for HT or SCANNER ANTENNA SMA window antenna
clip
$10.95 AM 800
BNC
window antenna clip
$11.95
AM 801B
|
|
SMA or BNC "HAT" Clip-on
Mount
SMA
$10.95, AM 550
BNC Hat
Clip
$11.95 AM 551
|
|
 NMO
Antenna
Mount
RAIN CAP.
Used to cover the NMO mount when not in use.
Comes in basic gloss black.
The NMO cover with
built-in "0-Ring" seal.
.99 ea, Order
NMO5
|
|
HOLE PLUGS Drilled the hole in the
wrong place? Removed an old base-loaded antenna; This black rubber plug
is inserted into the hole to seal from moisture. It can be painted to
blend color.
The profile is about 1/8 inch high when
inserted,
Plug for 3/8"
hole .99
Plug for 1/2" hole .99
Plug for 5/8" hole .99
Plug for 3/4" hole .99
Plug for 7/8" hole .99
Plug for 1" hole .99
|
|
 This
NMO Hole Mount will fit into a 3/8" hole, or use the adapter (included) to
adapt it to a 3/4" hole. The BUX CommCo NMOH is supplied with 17 ft of
98% shielded RG-58 cable terminated into a PL-259 UHF connector. Cables
are attached at right angles to the mount. Mounts also include a built-in
seal around the mounting hole to protect from moisture.
AM-207B $8.95
|
|
 Trunk
Lip, NMO Mount, model AM-209 is a trunk-lip mount supplied with 14 ft of
RG-58 cable, a PL-259, and the industry standard NMO mount. The AM-209
mounts on a standard trunk-lip and comes with 14ft of cable terminated in
a PL-259.
AM-209 $11.95
|
|
NMO mount only. For virgin installation when cable is already in place.
No cable, only the NMO mount. Hardened Brass.
$4.95 NMO-2
|
|
ANTENNA ADAPTER
3/8"x24 thread base antenna to NMO Mount
When you don't care to drill another hole for that
whip, or new antenna, this heavy-duty adapter mates a 3/8"x24
thread antenna base to an NMO mount. Also includes "O" ring-to-body,
seal to prevent moisture oxidation.
NMO-6 $8.95
|
|
 NMO
to SO239 Antenna Adapter
When you don't care to drill another hole for that whip, or new antenna,
this heavy-duty adapter mates a SO-239 (PL259 type) antenna base to an NMO
mount. Also includes "O" ring-to-body, seal to prevent moisture oxidation
.
$8.95
NMO8
|
|
 Dual
Band, Trunk Lip Mount, Antenna
Trunk Lip Mount has steel lip clamp and dual set-screws.
With standard
3/8" X 24 thread base. Pre-wired with 17" of RG-58 to BNC
Connector. Black rubber paint protector, see photo.
Includes a PL-259 adapter/connector
$16.98 TLM7519
|
|
Trunk Lip Mount (ABS) with steel
lip clamp and dual set-screws. Accepts
antennas with standard
3/8" X 24 thread base. Pre-wired with 17" of RG-58 to BNC
Connector. Black rubber paint protector, see photo.
$7.97 TLMPL259
|
|
 "The
Adapter" is the best
way to describe it ! Our number one seller when it comes to antenna
adapters.
$
2.99 each Order 7060
BNC male to UHF
Female $2.99 ea
|
|
 QUAD
MAGNET, Antenna Mount.
Available in; Triple
Chrome
Plate, or Basic Black.
You
asked for strength in a super mobile antenna mount, and WE DELIVERED !
Features 4, five inch Heavy-Duty
magnets, equally spaced on a Heavy Duty, 1/4" thick, hard-drawn metal
frame. The BUX4MM is prewired with 3/8" X 24 threaded (standard) Mount,
and PL259 connector. Accepts 3/8 X 24 antennas
$44.97
BUX4MMC "chrome"
$44.97 BUX4MMB "Black"
|
|
You've heard about it, and here it is;
The GOLDEN Super "ROD" antenna Six section, telescoping
"rod" antenna for hand-held transceivers VSWR: Less than, 1.5:1
Connector: BNC male
Length: 108cm extended (48") and 26.5cm
collasped. approx.
$12.95
|
|
MARINE ANTENNA
No Ground VHF Marine Antenna.Ideal
for bass boats, small run-about, and sail boats. 3 dB gain effectively
doubles your transmitter's effective radiated power. Great for
auto's with fiberglass body's or for wood craft - no
ground required. Low profile 36" height is ideal for top
mast mounts on sailboats or for use on bass and ski boats or run-a-bouts
where long antennas might hamper operations. Comes complete with stainless
steel "L" type mounting bracket and preassembled 15' coax cable fitted
with PL259 connectors. |
|
Our
MoBALUN is also ideal for marine antenna installations.
When you hear those strong HF mobile
signals, here's one reason they stand out from the rest. By installing
the BUX MoBalun near the input to your antenna, you deliver more RF energy
to the antenna. At the same time, the BUX MoBalun prevents RF from
traveling back along the shield (high SWR) of your coax. High power
rating, Low-permeability toroid, with Internal composition fiber-glass to
prevent vibration during mobile operation. For input and output
connectors, we use only the best Silver plated, Teflon insulated, SO239
connectors. 500 watts. |
|
HR-22 $7.99
|
|
$37.97
|
|
17.95
MOBALUN
|
|
|
3 inch, NMO Magnetic antenna mount. Black
finish,
and a good "grabber" to a smooth, flat, metal surface. A good
 companion
mount for the DB-2. Black finish, and a good "grabber" to a smooth,
flat, metal surface. A good companion mount for the
UV325 shown near top of this
page. |
|
5 inch, NMO Magnetic antenna mount. Black
finish,
and a good "grabber" to a smooth, flat, metal surface. A good companion
mount for the DB-2 shown on this page. This is a
Larger, 5 inch heavy duty Magnet, w/coax and connector. 5 inch, NMO
Magnetic antenna mount. Black finish, and a good "grabber" to a smooth,
flat, metal surface. A good companion mount for the
UV325 shown near top of this
page. |
|
 DB-2Dual Band mobile antenna for 144 & 430 MHz
VSWR: Less than, 1.5:1 Connector: NMO base. Length: 39cm or
15.5 in. approx. ADD the NMO, 5 inch
magnet mount for a durable, dual-band mobile antenna combo |
AM-1043B
3.5 Inch, $14.95
|
|
AM-1045B 5 Inch $17.95
|
|
DB2
$14.95
|
|
 |
|
Hi Quality Belden coax nine ft. jumper made using
top quality Amphenol connectors.
$6.97
ORDER No. HIQ9JMPR
|
|
AM-101. Magnetic SO239 Mount 3.5" strong magnet mount
with black plastic finish. 17' RG58 coax with PL-259. |
|
|
12.99
|
|
|
|
 F=1-5/8"
T=1"
S=1-1/8"
C=1/4"
W=5/32" |
Eyebolt with nut, Machine Thread Zinc Plated.
 5/32"
X 1-5/8" EYE = 1/4"
HUNDREDS OF USES !
BALUN hang'n-hook, mobile antenna tye-downs, rope guide
on tower, or pull-up masts, and much more. |
Order EYEBOLT
39 cents each
Order EYEBOLTX3
3 for 99 cents
|
|
|
Both, DB-2 and 1045B for only:
$29.95 |
|
Great for Apartment Dwellers, RV,
pickup truck-bed rail, or Bumper
installations. Rail
or Bumper Heavy-Duty Antenna Mount
Length of this bar is 12 inches, and width is 2 inches.
The bar is almost one quarter inch thick. Mounting screws and 3/8" X 24
standard thread, stud mount are included.
By using our KD-3 Kwik-Disconnect,
you can quickly change bands, or make your antenna setup into a "stealth"
installation |
|
Shown here is our T-BAR TRUX Stake hole
mount. This one is for the serious HAM. The T-Bar mount is
constructed of stainless steel and locates the antenna directly over the
truck bed rail. Expandable rubber base locks mount for
secure fit when tightened. Great for our HF stix and out heavy-duty whips.
Fits most pickup truck models and brands. Heavy Duty Right angle
SO239 and 3/8" x 24 threaded stud, included, |
|
$29.95
DB2-45
|
|
$14.95 order BUXTRUXHD
|
|
TSTAKMNT $22.95
|
|
←ZIP
2 Mbytes PDF→
We Accept;
Heavy Duty
Spring for Whips up to 102 inches.
Often called the
mobile antenna, Kwik-Disconnect 
Lost the
ferrule that holds your whip-tip atop your BUX-STIX antenna? Here is
the replacement complete with set-screw. Threads are standard 3/8 x 24.
AM370RS
Replacement,
Hardened, Nylon, Heavy duty, Shoulder washer insulators, same as
shoulder washers in SM1 Stud-Mount. 
