BUX  BOSS  BALUN This is our BUX COMM High-Performance "HAMMER." We designed it to cope with a "wholesome" kilowatt... or two, or  three.  We decited that was NOT good enough, so we built it to endure harsh treatment. STATS: 10" x 4"  Wt. 1.5 LBs 4:1 Hi-Power, 160 thru 6 Meters HEAVY DUTY TOROID MADE OF TYPE 43 FERRITE, FOR LOW PERMEABILITY 4:1 High Performance, Heavy Duty, *3 KW Balun (if SWR is less than 2:1)   *CW/SSB duty-cycles only.  SSB/CW Power @ 3.5 MHz* >2 kW if SWR is less than 3:1, Not rated for RTTY & AM Will not saturate at Amateur Radio Power Levels  Regular $64.97     Now at BUX COMM $ 39.95 Order 3KBBB

With an increase in local noise sources and the increasing attractiveness of long wire and dipole antennas, coax cable has become the antenna feed line of choice for most radio users and operators.    Given that the impedance of most commonly available coax is either 50 or 72 ohms and since many wire antennas present an impedance of 200 to 600 ohms or more at the feed point, direct connection of the coax to wire antennas hits us with a significant signal loss due to the antenna impedance mismatch.    Having realized this set of circumstances in the receiver and SWL arena, we're introducing a new approach to defeat the noise and impedance mismatch problems in our receive antennas by designing this new RxBALUN�.   Our RxBALUN� bridges the impedance gap, and enables an unbalance to balanced match between the antenna and our receivers.  These features provide more signal transfer from the antenna to your receiver.     Our RxBALUN will accommodate the SWL and QRP Operator.  In addition, this RxBALUN may be employed as an antenna balun for both transmit and receive between the antenna and low powered transceivers running up to 200 watts.  For input and output connectors, we use only the best Silver plated, Teflon�� insulated, SO239 connectors. Max Power 250 watts. $14.97 RxBALUN     Teflon �� E I DuPont corp.

2212 EEPROM used in the RANGR, DELTA, and PHOENIX GE trnasceivers for 16 channel frequency/program control. Stock # XR2212  $19.00 ea    or 10 for $165.00

Keep your Mobile RF Power at your antenna.  When operating mobile, every watt your transceiver sends is valuable.  Add the BUX MoBALUN and be one of the mobile signals that stand out from the rest.  By installing the BUX MoBalun near the input to your antenna, you deliver more RF energy to the antenna. At the same time, the BUX MoBalun prevents RF from traveling back along the shield of your coax as (high SWR), therefore more power is transmitted as useful RF energy. High power rating, Low-permeability toroid, with Internal fiber-glass composition to prevent unnecessary vibration during mobile operation.  For input and output connectors, we use only the best Silver plated, Teflon�� insulated, SO239 connectors, and Amphenol PL259,  with 20 inches of RG8X to connect to the input of your antenna.  Power rating of our BUX MoBALUN is 1000 watts.    Our MoBALUN is also ideal for marine antenna installations.   $19.95 MOBALUN  Our MoBALUN is also available with binding-post "terminals." ORDER MOBALUN-T   $ 19.95 Teflon �� E I DuPont corp. Amphenol �� TYCO Corp.

MOBILE KING, Antenna UNUN For bottom fed, and Screw-Driver antennas. 1.8 MHz to 50 MHz  Master Match MOBILE KING "Big Talker"  UNUN   o  FREE  3ft RG8X coax jumper with PL259's. o 1.8 to 50 MHz o Ferrite (current) Broadband Toroid design o Heavy Duty, Lightweight construction o SO-239 UNbalanced input. o SO-239 UNbalanced output, o Sealed against moisture    Order SDAB  UNUN  $19.95

Remember this automobile "noise suppression kit."  Well, I have acquired several of these jewels of the past.  What you see, is what you get.... and for only Five Dollars per kit.  Yes, that is a coaxial, feed-thru capacitor, and 3 feet of 1/2 inch wide grounding braid.  The black (resistor) distributor wire is of little use with electronic ignitions.  The kit originally sold by GE communications for  $38.00. Your cost:  $4.75     Stock #   NSKIT

		ANT202 is a Base Station, (dipole) antenna for (HF) 20, 17, 15, 12, and 10 meters.  We've also used it on 2 meters and 220 MHz with amazing success. INCLUDES 2 end insulators. A202 $27.95 ← For improved HF performance, we recommend our 101 BALUN (reg $ 19.95) A202 & BALUN B101 SAVE $8.00, Order AB102 Both for $ 39.95 AB102
This 450 Ohm ladder line comprises poly-coated open wire. It is much easier to handle than open wire feeder yet retains its ultra low loss feature.  This feed-line will handle 1 kilowatt with ease and is far superior to the 300 Ohm ribbon type.		100 feet   $ 19.95 Cat #  450LADR   50 feet    $ 11.95 Cat #  450LADR50
	100 feet of RG-8U Low-Loss, Base-Station Coaxial Cable.   It's low loss design and 97% or better shield makes it ideal for this application. GOLD PL-259 coax connectors are installed on each end	50 feet of RG-8U with 97% shielding, Low-Loss, Base-Station Coaxial Cable. ORDER:  RG8PL1L $39.97     Both ends are fitted with "GOLD" plated PL259/7506 connectors !    100 feet of RG-8U, with 97% shielding, Low-Loss Base-Station Coaxial Cable. ORDER:  RG8PL1C $59.97
Number 14 TW/AWG with 41 strands of tinned copper wire, Poly-Vinyl insulation covered flexible, but strong.  The most preferred wire type when building Dipole's, Windom's, and other flat-top HF antennas.  The PVC insulation gives added strength to the 41 strands of tinned, copper wire.  Specification:  Finely stranded tinned copper conductor (Type III),  105�C   600 volt copper. 1.5lb/100 Color coded PVC insulation, Temperature range  -20�C to 105�C, Voltage rating 600 volts, Reistant to Acid, Alkilis, Abrasion, Flame, Gasoline, Oil, Ozone, Moisture, Fungus.   100 ft, $19.95 10016 ;   200 ft, $38.95,  20016 300 ft, $57.95 30016 ;   400 ft,  $76.95  40016