BASE STATION ANTENNAS and ACCESSORIES
TOLL FREE, anytime Orderline 1 866 300 1969 operator's are on duty: ORDERS ONLY, 
When calling the Toll Free number, be sure to have your Order numbers ready
FAX 24/7, (434) 525 7818 BUX COMM is Better, and Faster, shipping from our larger facilities.
Dealer Orders  Monday>Friday, 10 AM > 4 PM EDST, 1 434 534 8873    
All orders ship same business day, if received before 3 pm Eastern Time.
 For tech support, Email:  s u p p o r t @ B U X C O M M . c o m
We Accept;
NOTICE: We ship WINDOM and G5RV antennas worldwide, However; Due to excessive damage, we cannot ship HF Mobile or VHF Base antennas outside the continental USA !

  MOBILE Antennas  

↓ This 160 thru 6 meter WINDOM is completely assembled ↓

BUX Model 166260 includes three (3) insulators, PVC covered, Power-Flex, 41 strand, tinned, copper wire, connectors, and "BUX Black Hawk BALUN".  This 160 thru 6 meter WINDOM is completely assembled, ready to connect your coax, and erect.    You can be on the air in no time, with our model 166260,  $79.95                
In Stock  $79.95  Order ↑WINDOM ↑ "without coax" Model 162260 

166260 Windom with One Hundred ft. (100') RG8X coax and connectors, $ 129.95 162260W100 

The illustration shown here is for use with the BUX COMM WINDOM models. 
This configuration may not perform with other antenna types.

With one of our BUX WINDOM antenna installations, we have about 24 feet at each end hanging down as shown, and I've noticed improved contacts with other stations using "vertical" antennas.
↓ This 80 thru 6 meter WINDOM is completely assembled↓

BUX Model 806136 is SSB power rated at 1000 watts and includes three (3) insulators, PVC covered, Power-Flex, 41 strand, tinned, copper wire, connectors, and BALUN.  This WINDOM is completely assembled, ready to connect your coax, and erect.  See coaxial cable and related items below.  You can be on the air in no time, with our model 806136,  $59.95   
 In Stock  $59.95  Order ↑WINDOM ↑ "without coax" Model 802136 

PREMIUM BONUS !!!

Above Windom (COMPLETE), with Fifty ft. (50')  RG8X coax, $ 79.95 802136W50  
Above Windom (COMPLETE), with One Hundred ft. (100') RG8X coax, $ 95.95 802136W100
40 thru 6 meter WINDOM completely assembled

Total length; 70 ft overall, comes complete with BALUN, center insulator with eye-bolt (as shown), end insulators, and end ty-tails, attached. 

 

Without coax feedline    Complete and ready for you to connect your coax.       order number “40670”  For $49.95        

 

With 50 ft of RG8X coax with Gold PL259 already installed at each end, it is our  order number 40670X50 for $ 68.95     

 

With 100 ft of RG8X coax with Gold PL259 already installed at each end, it is our order number 40670X100 for $ 87.95  


The BUXCOMM model 1606G5RV Antenna
is complete, and include:

• 205 feet of number 14 (awg) composed of 41 strands of silver plated copper wire, labeled as BUXFLEX www.BUXCOMM.com.
• For esthetics, wire has sky-blue covering.
• Sixty three feet of UV resistant coated, copper-clad Ladder-Line
• BUX “CARDINAL” BALUN.
• End (strain type) Heavy-Duty ceramic “egg” Insulators
• Center Support Insulator
• All connections are silver-soldered and coated with water-resistant compound and covered with 3M Weather-tite, shrink.

The overall length of the BUXCOMM model 160605G5 antenna 160 through 6 meters (also covers 30, 24, 17and 12 meters), is 205 feet. The UV resistant ladder-line is 63 feet, and the lower end terminates into our 1 kW, BUX "CARDINAL" BALUN.

The complete 160 thru 10 meter, BUXCOMM model 1606G5RV antenna SSB power rated @ 1000 watts.  All connections are made and insulators installed.  Includes "BUX "CARDINAL" BALUN" from BUX COMM:  Just as it appears here,  just hang it and connect the coax.    BUX "CARDINAL" BALUN IS INCLUDED; and Complete for only $59.95.   
                                         Order Model 1606G5RV

PREMIUM BONUS ! G5RV (complete) with fifty feet (50') of RG8X coax, $ 79.95 1606G5RVL  

USER INFORMATION:
The antenna ends should be secured with nylon rope or suitable supports.  The ladder line is 63 feet, and should have a near vertical (or slanted) drop from the center insulator for at least 25 feet and kept away from conductive objects. If the ladder line is installed near metallic or conductive objects, support the ladder-line as far from these objects as possible.  PolyVinyl conduit (PVC) stand-off supports at least 12 inches long can be employed to prevent contact with conductive objects, and tree limbs. UV resistant ties should be used to secure the ladder-line to insulated supports.

BUXCOMM  model  G5RVPNP  75 through 10 meters

Figure 1;  The G5RV is often used with an antenna tuner to operate as a Multi-Band HF antenna

The complete G5RV antenna SSB power rated @ 1000 watts SSB.  All connections are made and insulators installed.  Includes "BUX RED BARRON BALUN" from BUX COMM:  Just as it appears here,  just hang it and connect the coax.    BUX "CARDINAL" BALUN IS INCLUDED; and ALL for only $39.95.   
                                         Order Model G5RVPNP

PREMIUM BONUS !!!  G5RV (complete) with seventy feet (70') of RG8X coax, $ 66.95 G5RVB70  

BUX COMM LOOP ANTENNA

In Stock  $99.95 Order ↑BUXLOOP ↑"without coax" SEE COAX OPTIONS BELOW.
 

The "LOOP Sky-Wire" is completely assembled, with all wire, "float" insulators, "center fixed" insulators, BALUN (UnUn), ready to hang and attach your coax. 

*  LOOP Antennas have less electrostatic noise in your receiver.
*  LOOP Antennas provide additional gain over conventional wire type antennas
*  LOOP Antennas perform especially well over poor conducting earth like sand and lossy soils.

Many HAMs will tell you about a great antenna that was designed by Dave Fischer W0MHS.  For now though, let's say that the best overall performing wire antenna is one of the best kept secrets in HAM Radio.  I first learned about it in 1985 when Dave W0MHS wrote an article in the November issue of QST.  Dave called his design, "the   ''Loop Skywire.''  Today, we call it, the Full Wave LOOP Antenna.
 

There are several factors to consider when choosing your wire gauge and type. BUX COMM uses number 14 AWG, silver-flashed-copper, made up of 41 strands, covered with Sky-Blue PVC. The (41) multi-strands provide an added (tensile) strength.   Because the wire size, most often referenced by HAM radio articles, is: #14 AWG, we have chosen it as the preferred size for our Full Wave, 80 thru 10 meters, LOOP antenna wire size.   In the construction of our antennas here at BUX COMM, we use a special, high grade wire, with 41 strands of silver flashed, copper with an esthetically blended sky-blue IR resistant PVC covering.  Our sky-blue covering will not affect the RF transmission in any way.   The formula we use to calculate the length of the Full Wave Loop Antenna is; L = 1005/f   "F" being the frequency of the lowest band to be used.   This formula is as accurate as you will need or want for the "loop antenna" on the HF bands. 
 

HF loop antennas can be constructed to be supported in one of two ways, "fixed and floating."  We use both methods of support.  For insulators to the right, left and diagonal of/to the feed point, we "float" the support insulator(s). 
 

When using one of the corners as the feed point, we employ a "fixed" insulator with a center hanger eye.  Diagonal to the feed-point and at the two non-fed corners, we employ "floating" insulators. This enables the wire to move freely, thus providing the best support when the horizontal loop is supported by tall poles or swaying trees.

The BUX COMM 80 thru 10 meter Full Wave LOOP Antenna is complete, including: all insulators installed, the BALUN (UnUn) installed, and all connections silver-soldered and weather-proofed.  All that is left is hanging it and connecting the coax feedline to the BALUN/UnUn.   See the *50 and **100 ft coax options for the Full wave LOOP antenna below.

 In Stock  $99.95 Order ↑BUXLOOP ↑ "without coax"  

Full Wave Loop Antenna Coax options
 *Above FullWave LOOP complete, with Fifty ft. RG8X coax with gold PL259s attached                119.95  BUXLOOP50  
**Above FullWave LOOP complete, with One Hundred ft. RG8X coax with gold PL259s attached  144.95 BUXLOOP100

 

ANT202 is a Base Station, antenna for (HF) 20, 17, 15, 12, and 10 meters.  We've also used it on 2 meters and 220 MHz with amazing success.
INCLUDES 2
end insulators.
 

 

A202 $27.95
←
 

 

For improved HF performance, we recommend our 101 BALUN (reg $ 19.95)
A202 & BALUN B101
SAVE $8.00, Order AB102

Both for $ 39.95  AB102  

 

Thru-Glass Scanner antenna. 

 

Covers 20 MHz to 1200 MHz. 

 

Supplied with 14 ft of coax with connector and mounting materials.  Installation instructions and recommended mounting location.                                                                                    

9.95  Order SCANT

EGG "strain" type ceramic, 1-3/8" insulator. Used as antenna end insulators, and for breaking up resonant or "Hot-Tower" guy wires.

3 for 1.99   Order 3EGG
 

450 Ohm ladder line comprises poly-coated open wire. It is much easier to handle than open wire feeder yet retains its ultra low loss feature.  This feed-line will handle 1 kilowatt with ease and is far superior to the 300 Ohm ribbon type.
 100 feet   $ 19.95 Cat #  450LADR  

50 feet  $ 11.95   Cat #  450LADR50

The cable shown here is 8 conductor Rotor Cable stranded with UV resistant PVC insulating jacket.

Wires 1 & 2 are Number 16, stranded, and tinned copper.

Wires 3 thru 8 are number 20, stranded, and tinned copper.

50 ft, $19.50   ROTR50        100 ft, $37.50,  ROTR100  


200 ft, $75.00 ROTR200      300 ft,  $111.95  ROTR300

Dipole and inverted-Vee antennas are commonly "balanced" at the feed points.  Coaxial feed lines are "unbalanced" by design personality (thus the name BALUN).  This BALANCED, to UNBALANCE marriage can only be performed by using a BALUN.  A BALUN should always be used when feeding wire antennas with coax to make certain characteristic antenna performance and optimum transfer of RF energy to the antenna complete.

When coax is used to feed antennas without the benefit of a BALUN, current flows on the shield of the coaxial feed line .  This coaxial shield current can produce  a "Hot HAM shack,"  This can result in nasty R.F. injury from the microphone to lips, hand key to fingers, etc., and is often more pronounced at certain frequencies.  Coax cable shield currents can also cause damage to your HAM gear.   TVI, RFI, telephone and even wild VSWR indications can result from these shield currents.  

In 85% of antenna projects that displayed these problems, when a BALUN is added to the coaxial line or near the antenna feed point, these problems were diminished or completely eliminated.

MasterMatch™ 4:1
 BLACK HAWK

$19.95    MM41  

Our BUX Master-Match™ 4:1 current Balun is ideal for matching windoms, web'd or folded dipoles, and antennas fed at a 250 ohm to 500 ohm impedance feed point with normal 50 or 75 ohm coax cable. In contrast to ordinary Baluns the BUX MasterMatch™ 4:1 Balun support balanced currents in each leg of the antenna and prevents feedline (re)-radiation. As mentioned in our windom articles, feedlines and 450-ohm, brown, UV resistant, PolyCovered-Ladder-Line are easy to handle, and more-over they present another efficient means to feed multi-band antennas.  We strongly suggest the use of our UV resistant PolyCoat-Ladder-Line as it is made of strong, copper-clad, steel conductors. This light but durable, UV resistant Ladder-Line will  outlast the normal open copper with plastic spacers. (Includes three FREE antenna insulators, shown elsewhere, this page).

Master-Match™ "Black Hawk"  4:1 Features:
o DynaMAX Colored and Hardened, UV Resistant Resin Enclosure
o Toroid CURRENT design, wound with teflon covered, silver flashed, copper wire.
o 50 ohm, silver plated, gold pin, teflon center insulator, SO-239 unbalanced input
o Heavy duty Hardened Brass, Balanced output terminals.
o 160 Meters through 10 Meters
o Heavy Duty, Lightweight construction
o Sealed against moisture

At BUX COMM, *We don't cut corners! The components used in the manufacture of our BALUNs are from top quality components, beginning with the UV resistant enclosures, then the Silver Plated SO239 connectors with center insulator made of teflon™(E.I Dupont). The wire we wind the ferrite donut with, is heavy-duty, silver flashed wire, with teflon™ insulation, which will handle RF voltages above 2500 volts, and temperatures above 400 degrees. The binding posts are heavy-duty, tempered brass, with end holes and side-thru holes to accommodate either type loop-thru connection. A double-shoulder brass capture nut is used to add a secure bite and improve electrical connections to the wire .
SPECIAL   BONUS !
Buy either our Master-Match™ 4:1 BALUN or our Master-Match™ 1:1   BALUN and receive "FREE," a Package of three TyNITE™ Insulators, shown elsewhere on this page.   The BUX Master-Match™ 4:1 & Master-Match™ 1.1 High Performance ,  1.5  KW Balun (if SWR is less than 2:1)  *CW/SSB duty-cycles only.   SSB/CW Power @ 3.5 MHz* >1.5 kW if SWR is less than 3:1  *Not rated for AM, RTTY or other high duty-cycle digital modes.

MasterMatch™ 1:1
 CARDINAL
  $19.95   Order MM11  

BUX Master-Match™ 1:1 current Balun is ideal for Dipoles, Slopers, Inverted-Vees and center feed-point, RV antennas. They are also employed at the driven element of of many HF beams and Quads, and where feedpoint impedance is at, or near 50 ohms. By equalizing the currents in the antenna feeders, the Dipole pattern improves and prevents feedline (re)-radiation by preventing antenna currents flowing along the outer braid of the coax or transmission Line.
Master-Match™ 1:1 Features:
o DynaMAX Colored and Hardened, UV Resistant Resin Enclosure
o 50 ohm, silver plated, gold pin, teflon center insulator, SO-239 unbalanced input
o Heavy duty Hardened Brass, Balanced output terminals.
o 1.8 to 54 MHz
o Toroid CURRENT design.
o Heavy Duty, Lightweight construction
o Sealed against moisture

At BUX COMM, *We don't cut corners! The components used in the manufacture of our MasterMatch™ BALUNs are from top quality components, beginning with the UV resistant enclosures, then the Silver Plated SO239 connectors with center insulator made of teflon™(E.I Dupont). The wire we wind the ferrite donut with, is heavy-duty, silver flashed wire, with teflon™ insulation, which will handle RF voltages above 2500 volts, and temperatures above 400 degrees. The binding posts are heavy-duty, tempered brass, with end holes and side-thru holes to accommodate either type loop-thru connection. A double-shoulder brass capture nut is used to add a secure bite and improve electrical connections to the wire
SPECIAL  BONUS
Buy either our Master-Match™ 4:1 BALUN or our Master-Match™ 1:1   BALUN and receive "FREE," a Package of three TyNITE™ Insulators, as shown elsewhere on this page3 The BUX Master-Match™ 4:1 & Master-Match™ 1.1 High Performance ,  1.5  KW Balun (if SWR is less than 2:1)  *CW/SSB duty-cycles only.   SSB/CW Power @ 3.5 MHz* >1.5 kW if SWR is less than 3:1  *Not rated for AM, RTTY or other high duty-cycle digital modes.

AMERICAN EAGLE

2500 WATT BALUN
This is our BUX COMM High-Performance, Heavy Duty, "Big Talker"
We designed it to cope with a "couple" kilowatts... or  three.   We decided that was NOT good enough, so we built it to endure harsh treatment.

  STATS: Current Balun, Wt. 1.5 LBs, 4:1 Hi-Power, 160 thru 10 Meterz
  HEAVY DUTY TOROID MADE OF TYPE 43 FERRITE
  LOW PERMEABILITY CORE
  2500 WATT 4:1 current High Performance, Heavy Duty,
  *CW/SSB duty-cycles only.  SSB/CW Power @ 3.5 MHz* >2.5kW * SWR  is less than 3:1, Not rated for RTTY & AM
 Will not saturate at Amateur Radio Power Levels  Regular $64.97   

Order Model AE41 $ 34.95  

1:1 version High Performance, Heavy Duty, 2500 WATT (Current BALUN),
Order Model AE11  $ 34.95

ebux

BUX  Master-Match™ "Current Type" Balun 4:1 
 $19.95   DOVE41   
Our BUX Master-Match™ current type, DOVE 4:1 is power rated @ 1kw ssb (pep) and at 650 watts Average power.  This is the same BALUN we use on our 1 kw Windom antennas. It also performs well with the web'd multi-band or folded dipoles, and antennas with 250 ohm to 500 ohm impedance feedpoints where 50 or 75 ohm coax cable is employed.  In contrast to ordinary Baluns the BUX Master-Match™ DOVE 4:1 Balun supports balanced currents in each leg of the antenna and prevents feedline (re)-radiation. 

 

BUX  Master-Match™ "Current Type" Balun 1:1 
 $19.95   DOVE11   
Our BUX Master-Match™ current type, DOVE 1:1 is power rated @ 1kw ssb (pep) and at 650 watts Average power.  This is the same BALUN we use on our 1 kw Windom antennas. It also performs well with the web'd multi-band or folded dipoles, and antennas with 50 ohm to 75 ohm impedance feedpoints.  In contrast to ordinary Baluns the BUX Master-Match™ DOVE 1:1 Balun supports balanced currents in each leg of the antenna to prevent feedline radiation. 

 
 

MOBILE KING, Antenna UNUN
For bottom fed, and Screw-Driver antennas.
1.8 MHz to 50 MHz
 Master Match
MOBILE KING "Big Talker"  UNUN
 

o  FREE  3ft RG8X coax jumper with PL259's.
o 1.8 to 30 MHz
 o Ferrite (current) Broadband Toroid design
 o Heavy Duty, Lightweight construction
o SO-239 UNbalanced input.
o SO-239 UNbalanced output,
 o Sealed against moisture

 In Stock  Order SDAB  UNUN  $19.95

BUX UN UN De-Coupling transformer

"Decoupling Transformer"
BUX UN UN De-Coupling transformer, has SO-239 (female)input connector and output connector is 1 ft Mini 8 cable with PL-259 (male).   BUX ONION is an UNbalanced to UNbalance (UN-UN) decoupling transformer designed to be used by the Apartment dweller or the RV ops.  It is also used with the DBLSPCL antenna.   It is ideal for "slopers" and

High RF currents traveling along the coax feed-line shield can cause high VSWR. This decoupling transformer prevents RF currents from traveling down the outer shield of the coax. The input connector is an SO239 (female) and the output connector is a PL259 (male).
 

$19.95 UNUN 
BUX ONION $19.95
BUXUNUN

Teflon ®™ E I DuPont corp.
 Amphenol ®™ TYCO Corp.



 


A good method to suspend a balun and the center of your antenna without placing undue stress on the BALUN or the binding posts.

Stainless eyebolt is inserted into Tenyte "Center Insulator"  The "Center Insulator" is used to suspend the center of a Dipole,  Windom, or other wire type antenna from tower, tree, or support structure.

Center Insulator
with Suspension Eyebolt
 

      1.99  Order CIA   

Center Insulator and two end insulators  3.99
 Order CIAX3 

For the apartment dweller, you can now hang the 20 meter doublet in the attic.  I've QSO'd with stations all over the world with the 33 ft dipole in the attic of my garage.  One insulator at the center, and one each end.  It's great for other HF WINDOM and or dipole antenna.  Dielectric strength is better than the old ceramic insulators, but without susceptibility to cracking or breakage under impact or extreme temperature changes.

 

Package of  3,  $2.99   
 Antenna Insulators  

Package of 10,  Insulators $8.99, ANTINSLX10

F=1-5/8"

T=1"

S=1-1/8"

C=1/4"

W=5/32"

 5/32" X 1-5/8"

EYE = 1/4"

Eyebolt with nut, Machine Thread Zinc Plated

 Order EYEBOLT
39 cents each

Order EYEBOLTX3
3 for 99 cents

 

COMING SOON, "The RAVEN"

  • Double-co-efficient coupled design.

  • Exceptional High output.

  • Large ferrite cores.

  • Non-core saturating design.

  • High winding reactance with only an L-C compensation.

  • Hi-Temp insulated, large gauge, high temperature, Teflon coated wire.

  • Compensation for wide bandwidth

  • Rated at the legal power limit.

  • Stainless-steel eyebolts.

  • Input Connector SO-239

  • Output Connector Hard-Drawn, tempered Brass Binding Posts.

  • 4:1 Bandwidth 160 - >10 m.

  • 1:1 Bandwidth 1.8 - > 54 mHz.

Important Information;                                    WHY USE A  4:1 BALUN

Krusty Olde Kurt is now going to repeat himself.  Why? Because the same question keeps coming up over and over. And he wants everyone to get it right.   "I'm feeding my dipole with 600-ohm line.  At the station end I need a balun to convert to 50-ohm coax. I need a 12:1 balun, right?"   Wrong!  A 4:1 balun would be better.  Why is that?  If your dipole is up, let's say, 35 feet then on 80 meters it will probably have a resistance at resonance of about 40 ohms. The actual resistance depends on the height above ground in wavelengths. 

If the dipole is 40 Ohms then what do you see at the transmitter end of your 600 ohm line? If the line is a half-wave long (120 ft on 80 Meters) you'll see 40 ohms.   Remember, a half-wave line repeats what it sees at the other end.  But if it is a quarter-wave long you'll see 8500 Ohms!  At other line lengths you'll see impedances somewhere between these two extremes.   So you are not going to see 600 ohms at the end of your 600-ohm line. That only happens if you have a 600-ohm antenna hooked onto it. With such a variation in impedance at the trans­mitter end of the line there is no one balun transformer that will match it. Most of the time the impedance will be above the 50 Ohms of your coax so a high impedance balun would be desirable.  Unfortunately high imped­ance baluns don't work well when not matched.   

Experience has shown that 4:1 baluns work best in this service.  They are more rugged and will take bad mismatches especially if they are wound on an iron powder core.  So stop searching for that 12:1 balun. Use a 4:l BALUN and your system will work great.  

You can read Kurt N. Sterba “AERIALS” column in World Radio Magazine.

With an increase in local noise sources and the increasing attractiveness of long wire and dipole antennas, coax cable has become the antenna feed line of choice for most radio users and operators. 

 

Given that the impedance of most commonly available coax is either 50 or 72 ohms and since many wire antennas present an impedance of 200 to 600 ohms or more at the feed point, direct connection of the coax to wire antennas hits us with a significant signal loss due to the antenna impedance mismatch. 

 

Having realized this set of circumstances in the receiver and SWL arena, we're introducing a new approach to defeat the noise and impedance mismatch problems in our receive antennas by designing this new RxBALUN™.

 

Our RxBALUN™ bridges the impedance gap, and enables an unbalance to balanced match between the antenna and our receivers.  These features provide more signal transfer from the antenna to your receiver.  

 

Our RxBALUN will accommodate the SWL and QRP Operator.  In addition, this RxBALUN may be employed as an antenna balun for both transmit and receive between the antenna and low powered transceivers running up to 200 watts.  For input and output connectors, we use only the best Silver plated, Teflon®™ insulated, SO239 connectors. Max Power 250 watts.

$14.97 RxBALUN     Teflon ®™ E I DuPont corp.
CLOSE OUT  3KBBB11  1:1BALUN

STATS: Current Balun
10" x 4"  Wt. 1.5 LBs
4:1 Hi-Power, 160 thru 6 Meters
MEDIUM DUTY TOROID MADE OF TYPE 43 FERRITE, FOR LOW PERMEABILITY
1:1 High Performance, Heavy Duty,
*2 KW Balun (if SWR is less than 2:1)  
*SSB duty-cycles only.
 SSB/CW Power @ 3.5 MHz* >2 kW if SWR is less than 3:1, Not rated for RTTY & AM
 WAS  $59.97   
 Now at closeout price BUX COMM $ 27.95
 1:1 version High Performance, Heavy Duty,  (Current BALUN),
stock number 3KBBB11

Your BUX BALUN is warranted against defects in components or construction for a period of one year from date of purchase.  Our warranty does not cover damage due to misuse, abuse, or nonessential operation outside the  specifications of the BUX BALUN.  This warranty applies only to the original purchaser.  A copy of the receipt showing the purchaser’s name and the date of purchase must accompany BALUN's returned for warranty service.  All returns must be shipped prepaid.

Should there arise a requirement to return your BUX BALUN for service, carefully wrap and package it.   We will re-use your carton to return the BUX BALUN to you.  Be sure to include your return address.  Include a full description of the problem, along with your name, address, phone number and/or e-mail address.  Repairs average approximately 3 to 4 days.

SWL Antenna

This antenna may also be used as a 40, 20, and 10 meter Dipole for transmitting and receiving. MAX PWR 300 watts.
SWL, 68 ft, center-fed antenna complete with RxBalun and all insulators, end and center, coax feed is SO239. 29.95 + S&H
50 and 100 ft lengths of RG8X  with connectors, SO239 to match the above SWL antenna shown elsewhere on this page.

Order model  SWLANT  with BALUN  $ 29.95

EGG "strain" type ceramic, 1-3/8" insulator. Used as antenna end insulators, and for breaking up resonant or "Hot-Tower" guy wires.

3 for 1.99   Order 3EGG
 

 
Large EGG "strain" type ceramic, 2" insulator. Used as antenna center and end insulators, and for breaking up resonant or "Hot-Tower" guy wires.

3 for 2.99   Order  LEGG

For the apartment dweller, you can now hang the 20 meter doublet  in the attic.  I've QSO'd with stations all over the world with the 33 ft dipole in the attic of my garage.  One insulator at the center, and one each end.  It's great for other HF WINDOM and or dipole antenna.  Dielectric strength is better than the old ceramic insulators, but without susceptibility to cracking or breakage under impact or extreme temperature changes. In Stock
Package  of    3,   $2.99     Antenna Insulators  
Package of 10,  Insulators $8.99, ANTINSLX10

Stainless eyebolt is inserted into Tenyte "Center Insulator"  The "Center Insulator" is used to suspend the center of a Dipole,  Windom, or other wire type antenna from tower, tree, or support structure.

1.99  Stock#  CIA   

In Stock
Center Insulator and two end insulators  3.99  Order CIAX3 

* 1/4 wave on 2 meters   * 2.5 dBi gain at  440 MHz.   * Rated at 200 Watts * 12 ft of RG-58 cable with *PL-259 connector.  
* Magnet mount designed for winds of 100 mph  * Overall height is 21 inches.

$17.95  VU1510

Same as shown at left, but has *BNC connector for use with hand-helds with BNC antenna input. $18.95 each ORDER
VU-1510-"B"

$18.95 VU1510B

5/8 wave antenna,
136 - 174 MHz
NMO Base
(Mount not included)
39 inches overall
VSWR less than 1.5:1
200 Watts

VH-1215 $16.95

5/8 wave antenna,
220-265 MHz
NMO Base
(Mount not included)

VSWR less than 1.5:1
200 Watts
220-265 MHz version  PM220    $21.95 

 











$VU-1545

  

Recommended Mag Mount is AM-1045 B, NMO Mounts shown here.  Get both, the VU1545 VHF/UHF (NMO) Antenna & the AM-1045B, 5 inch, Super Heavy-Duty
Magnet Mount for $29.99
 

PM220  $21.95 

   17.95     BOTH 1545 &1045 
for $29.95  
   

Need a High Quality jumper from your transceiver to the linear?  A HiQuality coax jumper for that transceiver Output to linear input! The connectors are Amphenol™ and coax is RG-8X by Belden.  Hi Quality, Six ft. (6') jumper made using high quality components

  


Remember the axiom; 'An ounce of prevention is worth a pound of cure.'  This lightning protector contains a modified spark gap that provides that ounce of prevention. . Remember, there is no substitute for a good earth ground, AC line surge, and spike protection. Where lightning is involved, we make no warranties. We offer the 7516 as a secondary lightning protector. Ground wire attached to wire lug.  $ 4.99 ea  Stock # 7516

  

Kit contains:
2 - Adhesive Pads
1 - Alcohol Surface Cleaning Swabs
1 - Trim Plate
1 - Shrink Tube
REMOUNT KIT  for all TG Series (Thru-Glass) Antennas.

$6.97  HIQ9JMPR    STORM SEASON is just around the corner.  It pays to be prepared !
$ 4.99 ea  		  REMNTKIT  5.97
In Stock   In Stock   In Stock
BLACK CABLE TIES - 100pcs
.99 Pk of 100
Colour: BLACK (UV Resistant)
Dimensions (A x B): 98 x 2.5mm
Quantity: 100 pcs per/Pak
Material: polyamide (nylon 6.6) as specified in MIL-S-23190 self-extinguishing.
Temperature: -40°F to 230°F
Tensile strength = 18 pounds
A = 4 inches

.99 / Pak of 100
Order : KTFB3

    

140 - 170 MHz VHF
Economy Mag Mount Antenna.
 Order 2MMM  11.95

 

$ 6.95  each  


Dual Band Magnet Mount Antenna 14.95 Low-cost, high quality, dual band antenna with magnetic mount. Ideal for commercial two-way and HAM Radio VHF/UHF FM mobile applications. 200 watt rated.

DBMM  14.95

Use this mast-mounted bracket for 'fixed-station', field-day operating, apartment dwellers, or the mobile RV ops. 
With two of our mobile HF antennas  you can have the best of both worlds.  It is ou an ideal, single element, horizontal dipole (beam).  Shown mounted on 1 & 1/4" mast. Dual antenna bracket only, antenna(s) Not Included. 

See BUX HF STIX below 

DBLBRKT  $14.95
 

BLACK CABLE TIES - 100pcs
.99 Pk of 100
Colour: BLACK (UV Resistant)
Dimensions (A x B): 98 x 2.5mm
Quantity: 100 pcs per/Pak
Material: polyamide (nylon 6.6) as specified in MIL-S-23190 self-extinguishing.
Temperature: -40°F to 230°F
Tensile strength = 18 pounds
A = 4 inches

.99 / Pak of 100
Order : KTFB3

 


Great for HandHelds
and it is  ideal for use
as a rapid-deployment
antenna.

order VM101
$ 12.59

 

Number 14 TW/AWG with 41 strands of tinned copper wire, Poly-Vinyl insulation covered flexible, but strong.  The most preferred wire type when building Dipole's, Windom's, and other flat-top HF antennas.  The PVC insulation gives added strength to the 41 strands of tinned, copper wire.  Specification:  Finely stranded tinned copper conductor (Type III),  105ºC   600 volt copper. 1.5lb/100 Color coded PVC insulation, Temperature range  -20°C to 105ºC, Voltage rating 600 volts, Reistant to Acid, Alkilis, Abrasion, Flame, Gasoline, Oil, Ozone, Moisture, Fungus.  
100 ft, $19.95 10014 ;   200 ft, $38.95,  20014
300 ft, $57.95 30014 ;   400 ft,  $76.95  40014

100 feet of RG-8U Low-Loss, Base-Station Coaxial Cable.   It's low loss design and 97% or better shield makes it ideal for this application. GOLD PL-259 coax connectors are installed on each end 50 feet of RG-8U with 97% shielding, Low-Loss, Base-Station Coaxial Cable.
ORDER:  RG8PL1L
$39.97     Both ends are fitted with "GOLD" plated PL259/7506 connectors !   
100 feet of RG-8U, with 97% shielding, Low-Loss Base-Station Coaxial Cable.
ORDER:  RG8PL1C
$59.97    

50 Ohm impedance, 3ft, 6ft, 9ft, 12ft,18ft, 50ft & 100 feet.
These jumpers are made from high quality, low-loss, Belden coax cable with Amphenol PL-259 connectors installed.
 Three ft. (3')    ORDER No.      8X3PLPL  $3.99    
Six ft. (6')         ORDER No.      8X6PLPL  $4.99     
Nine ft. (9')      ORDER No.      8X9PLPL  $5.99     
Twelve ft. (12')   ORDER No.  8X12PLPL  $7.99  
Eighteen ft. (18')ORDER No.  8X18PLPL  $8.99  

Fifty ft. (50')   ORDER No.                       RG8X50PLPL  $22.95  
One Hundred ft. (100') ORDER No. RG8X100PLPL  $34.95  

BUX HF STIX  In Stock

BHF75M  75 METER  3/8" X 24 THREAD 8 feet long $16.95     

BHF40M 40 METER  3/8" X 24 THREAD  8 feet long $16.95       

BHF20M 20 METER 3/8" X 24 THREAD  8 feet long $16.95        

BHF17M 17 METER  3/8" X 24 THREAD 8 feet long $16.95        

BHF15M 15 METER 3/8" X 24 THREAD 8 feet long $16.95        

BHF10M 10 METER  3/8" X 24 THREAD 8 feet long $16.95        

BHF6M  6 METER  3/8" X 24 THREAD 5 feet long  $16.95          

These two-piece Mobile antennas consist of a hollow fiberglass base section approximately 1/2 inch diameter with the loading coil wound directly on the fiberglass and covered with shrink tubing.  The chrome plated brass base fitting has 3/8 inch X 24  threads that fit the amateur standard 3/8" X 24 mobile mount.
 

Replacement, 48 inch Tips for above tuneable-tip  antennas.    TIP48, $2.95      →       →      

BUX stix  HF antennas for Mobile and Base Applications:
 Power Rated at 250 Watts P E P;   Typical 2:1.VSWR band width is:

·        75 meter: 40 KHz.         40 Meter: 60 KHz.
·        20 Meter: 150 KHz.      17 Meter: 175 KHz.
·        15 Meter: 200 KHz.      12 Meter: 300 KHz.
·        10 Meter: 500 KHz.        6  Meter: 1000 Khz.

TUNING INSTRUCTIONS:
Insert the whip into lower section ferrule about four inches (as shown at right) and tighten set screw.   Assemble with fiberglass lower section (as shown at left). Install a VSWR meter at the transceiver and apply 10 to 25 watts of power. Adjust the VSWR meter and output frequency for lowest VSWR reading, indicating resonance.  If resonant frequency is too high, loosen set screw and extend top whip until desired resonant frequency is found.  If  resonant frequency is too low, loosen set screw and adjust whip further into lower section.  For best results, adjustments should be made in small increments. 

CAUTION:  If required, cut off the bottom of the whip to ensure it does not extend down into the coil of the antenna.  Failure to observe this precaution will cause heat damage and void any warranty.  At resonance, VSWR should be 1.5:1 or less when properly matched. When tuning is complete, tighten set screws securely.   NOTE: Bandwidth and VSWR will vary due to   mounting location.  If your installation has a VSWR over 1.5:1 at resonance, or you need to operate over a greater bandwidth a tuner may be required.

 

DBLSPCL (without BUX UNUN (ONION)

When the stations with the gain and power in their antennas are transmitting in the horizontal plane, then you should be meeting them in the same plane.  Horizontal signals tend to follow the earths contour, and are easier to capture using a horizontally polarized antenna.  See the BUX UNUN elsewhere on this page.

By combining a pair (two) of the single band HF Mobile (loaded) tuneable-tip antennas above, you can have an ideal, single element, horizontal dipole (beam). This type antenna opens the world of HF communications for the apartment dweller, RV HAM, field-day operating, and a variety of other uses and applications.  The packages described below include two antenna, the Double Antenna-Bracket (DBLBRKT), and mounting hardware.  $ 39.97 DBLSPCL (without BUX UNUN (ONION)
75 Meters→,  40 Meters→, 20 Meters→,

17 Meters→,  15 Meters→,  10 Meters→,

 

 6 Meters →         In Stock

BUX Double Combo "with" BUX ONION (UNUN).  
 By combining a pair (two) of the single band HF Mobile (loaded) tuneable-tip antennas above, you can have an ideal, single element, horizontal dipole (beam). This type antenna opens the world of HF communications for the apartment dweller, RV HAM, field-day operating, and a variety of other uses and applications.  The package described here include: two antenna, the Double-Bracket (DBLBRKT), mounting hardware, and BUX BALUN (UNUN).
$AVE,  BOTH, DPLSPCL & BUXUNUN, for only $ 54.97, ORDER, DBLCOMBO 
75 Meters→,   40 Meters→,   20 Meters→,

 17 Meters→,   15 Meters→,   10 Meters→

 

6  Meters →          In Stock

DUAL BAND, HIGH GAIN, BASE STATION ANTENNA, UVS-200
  6.7 db @ 2 meters, 8.2db 70cm. High Performance, High Gain, Dual Band, Base Station Antenna 5/8 wave, vertical stacked collinear design 2-5/8 elements on 2mt., 4-5/8 elements on 70cm.   6.7 db @ 2 meters and 8.2 db 70cm. Superior wideband performance Heavy duty fiberglass radome Durable, waterproof joints Mounting Hardware included Accepts standard PL-259 connector 200 Watt power rating Radiating element, 100 inches. DC ground, enclosed elements reduces terrestrial noise.


 

 

 

 

 Reg $109.95 BUX COMM price,  $57.97      

UVS-200         In Stock


Description:

2M/70CM DUAL BAND FIBERGLASS VERTICAL GAIN GROUND PLANE ANTENNA

HIGH PERFORMANCE , HIGH POWER RATING, LOW SWR AND BROADER BAND COVERAGE ON BOTH 2m AND 70cm BAND.

SPECIALLY DESIGNED TO KEEP THE ANTENNA STRAIGHT AS ONE ELEMENT.

USING RING GASKET MAKES ANTENNA PERFECTLY WATERPROOF.

EASY ASSEMBLY JUST BY TIGHTENING THE JOINT ACCORDINGLY.

INSULATED CONDUCTOR, LESS INTERFERENCE FROM RAIN, SLEET AND SNOW. REDUCED PRECIPITATION STATIC, LOWER BACK GROUND NOISE.

DC GROUND DESIGN LEADS THE HIGH VOLTAGE CAUSED BY THUNDER AND LIGHTENING TO THE GROUND, PROTECTS RADIO EQUIPMENT.

ACCEPTABLE MAST DIAMETER 30-62m/m (1-3/16" 2-7/16")

SUPPLIED WITH MAST BRACKET, V-BOLT, SUPPORTT TUBE AND ALL MOUNTING HARDWARE.

ELECTRICAL SPECIFICATIONS: LENGTH 2.5m (98.4"), GAIN 2m 6dB/70cm 8dB, CONFIGURATION 2m 5/8 WAVE 2-ELEMENT/70cm 5/8 WAVE 4-ELEMENT, FREQUENCY 144~148/435~450 MHz, MAX POWER 200 WATTS, IMPEDANCE 50 OHM, V.S.W.R LESS THAN 1.5:1, CONNECTOR SO-239 (UHF).
 Reg $109.95 BUX COMM price,  $57.97      

UVS200         In Stock

VH2201 VHF BASE & REPEATER Antenna.
Frequency Range:
136-174 MHz
Gain: 4.5dB
VSWR less than 1.5:1
Power Rating: 200 watts
Impedance: 50 Ohms
Stainless Steel Radials
SO-239 Input connector
Radiating element Length 6 feet.
Built to Commercial standards for base station installations,
and  rugged, mountain-top repeater applications.  Mounting
hardware and stainless-steel radials included.  Ship wt, 5 Lb

$47.97  VH2201             In Stock

UH2401 UHF BASE & REPEATER Antenna
Antenna Frequency Range: 430-490 MHz
Gain: 6.5dB
Power Rating: 200 watts
Impedance: 50 Ohms
Stainless Steel Radials
SO-239 Input connector
Radiating element
length 5 feet.   Built to Commercial standards for base station installations, and rugged, mountain-top repeater applications. Mounting hardware and stainless-steel radials included. Ship wt, 5 Lb

 

 $47.97 UH2401         In Stock

"Vertical" Six Meter Ground Plane


All mounting hardware and assembly instructions are included.

Also includes cutting chart for exact frequency measurements.


Solid Hard-Drawn Aluminum GP6M $49.95  In Stock

 

Two meter "Vertical" VHF Ground Plane
All mounting hardware and assembly instructions are included.

Also includes cutting chart for exact frequency measurements.
Solid Hard-Drawn Aluminum GP146 $34.95 

 

 

 

Dual Band, 2 meter (144 mHz) & 70 cm (440 mHz)
"Vertical" VHF & UHF Ground Plane
All mounting hardware and assembly instructions are included.

Also includes cutting chart for exact frequency measurements.
Solid Hard-Drawn Aluminum GP146440  $44.95 

VHF and UHF 'Cross-Needle' High
Performance, SWR & POWER Meter.
For the serious VHF/UHF operator, here is a 140 to 160 MHz & 440 to 480 MHz, VSWR and POWER meter with; 10 - 100 - 1000 watt scales.

 

 

 

 

SWR-6  $69.95           In Stock

SWR & WATT METER 100 watt & 10 watt level switch This is a handy, compact meter designed for the amateur radio operator. Test antenna performance and transmitter operation, 1.7 to 50 MHz. May also be used as a RF field strength meter and to check QRP.


SWR-3,  $19.95             In Stock

The perfect QRP SWR and Watt Meter.

SWR: 1:1 to 1:3;      RF Power: 0.5~10W;     Accuracy: =SWR: +- 5%
Power: +- 10%;        Impedance: 52 W,         Meter Sens. 200uA
                                    Freq. Range 1.7 to 30MHz


QRP, SWR & POWER Meter, (0.5 to 10 watts) with SO 239 connectors.
 

SWR-2T,  $12.99            In Stock

The Duplexer shown here is the ideal companion for our Dual-Band, Base Antennas  !  HF and VHF/UHF Antenna Duplexer  (Indoor use)


Frequency: (Port 1) 1.3 - 225 MHz,  (Port 2) 350 - 540 MHz
Power:       500 W 1.3 - 35 MHz,    300 W 50 - 540 MHz
Insertion Loss: <0.2 dB Isolation: 60 dB;    VSWR: < 1.2:1
Combine HF/6m/2m output (Port 1) and your UHF output
from your transceiver and send to one antenna.

In Stock

$34.95  Order DU-500    

 

Specifications:

 

Frequency Range:  Up to, and including 600 MHz
VSWR:  Below 1.2:1
Power Rating:  1.5 kW peak 1kW continuous
Impedance:  50  Ohms
Insertion loss:  Less than 0.2 dB.
Port Isolation:  Better than 50 dB.
Port connectors:  SO-239

One IN, Two Out, and
May be configured Two IN, One Out.

 2 Position Coax Switch

In Stock

CX-201  $19.95  

GOLD LINE 2 POSITION  Antenna Switch
Switch between Beam, and HF wire antennas, or between VHF/UHF and HF Beams.  RATED AT 1 kW.

 

In Stock

 

 

 

 GL1048  $ 9.95 


 

Antenna Coax Switch; 1  IN, 3 Out, in Metal case.
 Antenna Coax Switch; One IN, Three Out, or Three IN, and One OUT, 50 Ohm impedance, 3 port to 1 port Antenna Switch. Rated at 1 KW, SO-239 ports, mounted in metal case.

 

In Stock

 

CX3 $9.95 

 

 

HandHeld "HR-9" Duckie

Frequency:  144 - 148 MHz

SWR: Less than 1.5:1

Connector:  BNC Male

Length:   4 inches, or 105/mm

In Stock

9.95 HR-9 

 

 

 

 

 

 

 

 

HR-601VU
VHF & UHF Antenna

Dual-Band, HandHeld antenna, with SMA male connector for use with late model transceivers

 

 

 

In Stock

 

 

 

12.95  HR-601VU 

HR-601V is for VHF only handheld transceivers.

Frequency: 144-148 MHz
VSWR: Less than 1.8:1
Whip is Shape/Memory Alloy
Connector: SMA Male

 

In Stock

10.95  HR-601V

 

NMO Antenna Mount RAIN CAP.   
Used to cover the NMO mount when not in use.  Comes in basic gloss black.   
The NMO cover with built-in "0-Ring" seal.

 

In Stock                .99 ea, Order NMO5

 

HOLE PLUGS Drilled the hole in the wrong place? Removed an old base-loaded antenna;    This black rubber plug is inserted into the hole to seal from moisture.  It can be painted to blend color.   
  In Stock

The profile is about 1/8 inch high when inserted, 

Plug for 3/8" hole .99                Plug for 1/2" hole .99     

Plug for 5/8" hole .99                Plug for 3/4" hole .99     

Plug for 7/8" hole .99                Plug for   1" hole   .99   

This NMO Hole Mount will fit into a 3/8" hole, or use the adapter (included) to adapt it to a 3/4" hole.  The BUX CommCo NMOH is supplied with 17 ft of 98% shielded RG-58 cable terminated into a PL-259 UHF connector.  Cables are attached at right angles to the mount.  Mounts also include a built-in seal around the mounting hole to protect from moisture.    

 In Stock     AM-207B  $8.95

Trunk Lip, NMO Mount, model AM-209 is a trunk-lip mount supplied with 14 ft of RG-58 cable, a PL-259, and the industry standard NMO mount.  The AM-209 mounts on a standard trunk-lip and comes with 14ft of cable terminated in a PL-259.

In Stock     AM-209 $11.95  

NMO mount only.  For virgin installation when cable is already in place. No cable, only the NMO mount. Hardened Brass.

In Stock
$4.95 NMO-2  

 

 

ANTENNA ADAPTER
3/8"x24 thread base antenna to NMO Mount

When you don't care to drill another hole for that whip, or new antenna, this heavy-duty adapter mates a 3/8"x24 thread antenna base to an NMO mount.   Also includes "O" ring-to-body, seal to prevent moisture oxidation.

In Stock    NMO-6   $8.95   

NMO to SO239 Antenna Adapter
When you don't care to drill another hole for that whip, or new antenna, this heavy-duty adapter mates a SO-239 (PL259 type) antenna base to an NMO mount. Also includes "O" ring-to-body, seal to prevent moisture oxidation

.
$8.95 NMO8 

In Stock

 

Dual Band, 144-154 MHz & 440-460 MHz Trunk Lip Mount, Antenna
Trunk Lip Mount has steel lip clamp and dual set-screws.  With standard 3/8" X 24 thread base.  Pre-wired with 17" of RG-58 to BNC Connector.  Black rubber paint protector, see photo.  Includes  a PL-259  adapter/connector 

 

$14.95 DBTL270      In Stock

    

"The Adapter" is the best way to describe it !  Our number one seller when it comes to antenna adapters.

 $ 2.99 each  Order 7060    In Stock

BNC male to UHF Female  $2.99 ea

WINDOW CLIP for HT or SCANNER ANTENNA
SMA window antenna clip $10.95  AM 800 

BNC window antenna clip $11.95    AM 801B  

SMA or BNC "HAT" Clip-on Mount 
SMA $10.95,  AM 550  

 

BNC Hat Clip  $11.95  AM 551    

Your BUX BALUN is warranted against defects in components or construction for a period of three (3) months from date of purchase.  Our warranty does not cover damage due to misuse, abuse, or nonessential operation outside the  specifications of the BUX BALUN.  This warranty applies only to the original purchaser.  A copy of the receipt showing the purchaser’s name and the date of purchase must accompany BALUN's returned for warranty service or replacement.  All returns must be shipped prepaid.

Should there arise a requirement to return your BUX BALUN for service, carefully wrap and package it.   We will re-use your carton to return the BUX BALUN to you.  Be sure to include your return address.  Include a full description of the problem, along with your name, address, phone number and/or e-mail address.  Repairs average approximately 3 to 4 days.

 

QUAD MAGNET, Antenna Mount.
Available in; Triple Chrome Plate, or Basic Black.  You asked for strength in a super mobile antenna mount, and WE DELIVERED !  Features 4,  five inch Heavy-Duty magnets, equally spaced on a Heavy Duty, 1/4" thick, hard-drawn metal frame.   The BUX4MM is prewired with 3/8" X 24 threaded (standard) Mount, and PL259 connector.  Accepts 3/8 X 24 antennas

 

$44.97  BUX4MMC  "chrome"

$44.97  BUX4MMB "Black"

 

You've heard about it, and here it is; The GOLDEN Super "ROD" antenna Six section, telescoping  "rod" antenna for hand-held transceivers VSWR: Less than, 1.5:1   Connector:  BNC male

Length:   108cm extended (48") and 26.5cm collasped. approx.
 $12.95 

HR-22  $7.99 

Our "SDAB" UNUN (above)is an ideal companion for the VH-3200 Marine Antenna shown here.

VH3200 MARINE  ANTENNA
No Ground VHF Marine Antenna.Ideal for bass boats, small run-about, and sail boats.   3 dB gain effectively doubles your transmitter's  effective radiated power.  Great for auto's with fiberglass body's or for wood craft - no ground required.   Low profile 36" height is ideal for top mast mounts on sailboats or for use on bass and ski boats or run-a-bouts where long antennas might hamper operations. Comes complete with stainless steel "L" type mounting bracket and preassembled 15' coax cable fitted with PL259 connectors.
VH3200   $37.97

 

Trailer Hitch Mount with 7/8" hole for mounting with trailer-hitch ball, bolt.  For antennas with 3/8" X 24 (standard) antenna base. Stainless steel with SO239 coax fitting to receive PL259 coax connector.   Also accepts the BUX HF STIX shown above.   Stock number THM1   $ 11.95   

3 inch, NMO Magnetic antenna mount. Black finish, and a good "grabber" to a smooth, flat, metal surface.  A good companion mount for the DB-2.  Black finish, and a good "grabber" to a smooth, flat, metal surface.  A good companion mount for the UV325 shown near top of this page.  

  

5 inch, NMO Magnetic antenna mount. Black finish,
and a good "grabber" to a smooth, flat, metal surface. A good companion mount for the DB-2 shown on this page.    This is a Larger, 5 inch heavy duty Magnet, w/coax and connector.  5 inch, NMO Magnetic antenna mount. Black finish, and a good "grabber" to a smooth, flat, metal surface.  A good companion mount for the UV325 shown near top of this page.  

   DB-2

Dual Band mobile antenna for 144 & 430 MHz   VSWR:  Less than, 1.5:1 Connector:  NMO base. Length: 39cm or 15.5 in. approx.   ADD the NMO, 5 inch magnet mount for a durable, dual-band mobile antenna combo
AM1043B  3.5 Inch, $14.95
  AM1045B   5 Inch  $17.95 
 		  DB2  $14.95
In Stock   In Stock   In Stock
   

Hi Quality Belden coax nine ft. jumper  made using top quality Amphenol connectors. 

  $6.97    ORDER No.  HIQ9JMPR 

 

AM-101. Magnetic SO239 Mount 3.5" strong magnet mount with black plastic finish. 17' RG58 coax with PL-259.

  
12.99     

 

 

 

Both, DB-2 and 1045B  for only: $29.95

$29.95  DB245


 

Great for Apartment Dwellers, RV, pickup truck-bed rail, or Bumper installations.  Rail or Bumper Heavy-Duty Antenna Mount

Length of this bar is 12 inches, and width is 2 inches.  The bar is almost one quarter inch thick.  Mounting screws and 3/8" X 24 standard thread, stud mount are included.    By using our KD-3 Kwik-Disconnect, you can quickly change bands, or make your antenna setup into a "stealth" installation

$14.95  order  BUXTRUXHD 

Shown here is our T-BAR TRUX Stake hole mount.  This one is for the serious HAM.  The T-Bar mount is constructed of stainless steel and locates the antenna directly over the truck bed rail.    Expandable rubber base locks mount for secure fit when tightened. Great for our HF stix and out heavy-duty whips.  Fits most pickup truck models and brands.  Heavy Duty Right angle SO239 and 3/8" x 24 threaded stud, included,

TSTAKMNT  $22.95

Right Angle SM1L Mount Right angle stud mount with  SO239 coaxial cable connector and a 3/8-24 threaded antenna socket. Great for those cramped areas.  Reg 11.95,  BUX COMM Price:  $8.88

  

Pick-Up Truck, Flat-BAR,
STAKE HOLE
Mount  w/SM1

  

Adjustable Bumper Mount with 3/8"x24 thread SM-1, and SO239 (PL259) input.  Both may be used on hatch-back lid-lip, trunk-lip, bumper & hood.

$ 6.95  each  

  $19.95    442 S   $16.95
  
In Stock   In Stock   In Stock

BUMPER MOUNT with SO239 input connector, accepts PL259.   $9.95 Order 422-S 		   
422S  $9.95    Ball Mount with SO-239 (female) connector,
 AM601S $11.95  		  

Ball Mount with terminal lug connection,
AM601L   $11.95 
In Stock   In Stock   In Stock
Heavy Duty Spring for Whips up to 102 inches.  

Often called the mobile antenna, Kwik-Disconnect
This Mobile Antenna Adapter... is a 'SNAP' to change antennas or bands in a matter of seconds

  


Set of five (5) Kwik-Connect Antenna adapters and snap-on stud. Make changing mobile antennas a 'SNAP!' with a set of 5 ''Kwik Disconnect'' adapters.
S55S  $8.95   KD3  $5.95    KD5 $15.95  Set of 5.
In Stock   In Stock   In Stock

Order Line ONLY, Mon > Fri 10 AM to 4 PM,  434 534 8873  or FAX your order, 24/7 to FAX 434 525 7818

 

The EZ230 enables you to fold your mobile antenna over to a low-profile, horizontal position. 

This prone position allows entry into low-overhead garages, and prevents damage to the antenna.  A "must" for the mobile HAM.

 Both sleeve and threaded section are standard
3/8" X 24 threads.

 
 

Dual Band whip antenna for 144 & 440 MHz   VSWR:  Less than, 1.5:1 Connector: 3/8" x 24 threads dual-band mobile antenna.
As shown,  antenna only, requires 3/8 X 24 base. 

Lost the ferrule that holds your whip-tip atop your BUX-STIX antenna?    Here is the replacement complete with set-screw.  Threads are standard 3/8 x 24. 
 
EZ230  $9.95  14440WP $3.97

TIPFERL $3.97

In Stock In Stock In Stock


50 Ohm impedance, 3 ft, 6 ft, 9 ft, 12 ft, & 18 feet.
These jumpers are made from high quality, low-loss, Belden coax cable with Amphenol PL-259 connectors installed.
Three ft. (3')    ORDER No.      8X3PLPL  $3.99    
Six ft. (6')         ORDER No.      8X6PLPL  $4.99     
Nine ft. (9')      ORDER No.      8X9PLPL  $5.99     
Twelve ft. (12')   ORDER No.  8X12PLPL  $7.99  
Eighteen ft. (18')ORDER No.  8X18PLPL  $8.99  

Fifty ft. (50')   ORDER No.                       RG8X50PLPL  $22.95  
One Hundred ft. (100') ORDER No. RG8X100PLPL  $34.95  

 Shop Online or call our Order Line Monday thru Friday (except holidays) 1-434-534-8873
Customer Service  [email protected]
 Download our Catalog As of December 10th our brand new Winter 04/05 catalog is available in PDF FORMAT

Bumper Mount includes (SM1) SO-239 UHF connector to 3/8x24 antenna base (see SM1, this page).  $7.95 ea 

Included→    AM370RS

Insulated Antenna Stud Mount with SO-239 female connector for easy connecting with
PL-259 fitting. Threaded for standard 3/8 X 24 mobile antenna use.

$ 2.99  SM1 

10 for 17.95

Mirror-Mount with insulated stud, for 3/8 X 24 thread medium duty mobile antenna mounting.

AM304S

$6.95  Each    

Replacement, Hardened, Nylon, Heavy duty,  Shoulder washer insulators, same as shoulder washers in SM1 Stud-Mount.

4 for 99¢ SM1SW

DVM 810
 PocketCraft 810B. Here's a digital multimeter (DVM).  Ideal for the Mountain-topper HAM Radio Operator, or technician.  It has an LCD 3.5 digit readout
Features found on more expensive meters are standard on this DMM, they include:
* A transistor and diode tester
* DC Amperes

* AC Amperes
* Overload protection
* 7 functions & 19 Ranges
* Includes 21" test leads and battery.
Ranges to: 1000 Volts DC, 750 Volts AC, 10 Amps DC, Resistance to 2,000,000 Ohms

Order DVM810

$ 9.95

 

Order Line ONLY, Mon > Fri 10 AM to 4 PM,  434 534 8873  or FAX your order, 24/7 to FAX 434 525 7818

F=1-5/8"

T=1"

S=1-1/8"

C=1/4"

W=5/32"

 5/32" X 1-5/8"

EYE = 1/4"

Eyebolt with nut, Machine Thread Zinc Plated

 Order EYEBOLT
39 cents each

Order EYEBOLTX3
3 for 99 cents

ANTENNA  INSULATORS

Weatherproof, (TENYTE) insulators.  Perfect for your DIPOLE or Windom antenna.
For the apartment dweller, you can now hang the 20 meter doublet
in the attic.   I've QSO'd with stations all over the world with the
33 ft dipole in my garage attic.   One insulator at the center, and one each end.  

It's great for other HF WINDOM and single-band dipole antennas.  Dielectric strength is comparable to the old ceramic insulators, without susceptibility to cracking or breakage under impact or extreme temperature changes.
 Package of  3,  $2.99   ANTINSL3              
 Package of 10, Insulators $8.99, ANTINSLX10

VHF-UHF DOUBLE FEMALE BULKHEAD (feed-thru) CONNECTORS

                
YES, we have "one"  1 inch long                     For bulkhead and through-the-wall UHF connector feed-thru connections, with nuts.:

Order 75181  (One  inch )          $ 1.79 ea.               10 for $15.50  
Order 75182  (Two inches)        $ 2.95 ea.             10 for $ 24.50  

Order 75183  (Three inches)     $ 3.69 ea.             10 for $ 32.50  
Order 75184  (Four inches)       $ 3.95 ea.             10 for $ 34.50  
Order 75186  (Six inches)          $ 4.95 ea.             10 for $ 44.50  
Order 75188  (Eight inches)     $ 8.95 ea.              10 for $ 82.50  
Order 751810 (Ten inches)       $ 10.95ea.            10 for $ 99.50   
Order 751812 (Twelve inches) $12.95ea.             10 for $ 114.50 

         

               Heavy Duty 1" Nuts for the above bulkhead connectors.
2/.99 cents HDM1NUT        HDM1NUTX10 10 for $ 3.99  


 


50 Ohm impedance, 3 ft, 6 ft, 9 ft, 12 ft, & 18 feet.
These jumpers are made from high quality, low-loss, Belden coax cable with Amphenol PL-259 connectors installed.
Three ft. (3')    ORDER No.      8X3PLPL  $3.99    
Six ft. (6')         ORDER No.      8X6PLPL  $4.99     
Nine ft. (9')      ORDER No.      8X9PLPL  $5.99     
Twelve ft. (12')   ORDER No.  8X12PLPL  $7.99  
Eighteen ft. (18')ORDER No.  8X18PLPL  $8.99  

Fifty ft. (50')   ORDER No.                       RG8X50PLPL  $22.95  
One Hundred ft. (100') ORDER No. RG8X100PLPL  $34.95  

Need a High Quality jumper from your transceiver to the linear?

A HiQuality coax jumper for that transceiver Output to linear input!

The connectors are Amphenol™  and coax is RG-8X by Belden.

Hi Quality, Six ft. jumper  made using high quality components. 

    $6.97    ORDER No.   HIQJMPR                                  

Reinforced, Double Bracket used with our "DBLSPCL" antennas shown elsewhere on this page.

Mount two mobile whips in a horizontal plane to form a compact apartment dweller Dipole,  or RV antenna.  Comes with mounting hardware and double Antenna Bracket as shown at left.
$16.95   DBLBRKT  
 

After a few years, the hardened, nylon shoulder washers become weather-brittle and break.  Keep a few spares in the Ham Shack:  
     4 for 99¢ SM1SW


Mobile tuneable-tip antennas.

BHF75M  75 METER  3/8" X 24 THREAD 8 feet long $16.95

BHF40M 40 METER  3/8" X 24 THREAD  8 feet long $16.95

BHF20M 20 METER 3/8" X 24 THREAD  8 feet long $16.95  

BHF17M 17 METER  3/8" X 24 THREAD 8 feet long $16.95 

BHF15M 15 METER 3/8" X 24 THREAD 8 feet long $16.95  

BHF10M 10 METER  3/8" X 24 THREAD 8 feet long $16.95 

BHF6M  6 METER  3/8" X 24 THREAD 5 feet long  $16.95   


Spare 48" Tips for above tuneable-tip antennas.TIP48, $2.95 

Here's the perfect solution for your RV and portable HF antenna applications.  Use our dipole, mast-mounted bracket for 'fixed-station', field-day operating, apartment dwellers, and the RV travelers.  With two of the mobile HF antennas shown at left, you can have the best of both worlds.

By combining a pair (two) of the single band HF Mobile (loaded) tuneable-tip antennas, and (VHF) whips at left, you can have an ideal, single element, horizontal dipole (beam). This type antenna opens the world of HF and VHF communications for the apartment dweller, RV HAM, field-day operating, and a variety of other uses and applications.  Antenna(s) Not Included.

$16.95 each
 DBLBRKT 
tuneable-tip antennas allow adjusting for minimum VSWR.  CLICK HERE to read more about our HF DIPOLE SPECIAL!

By combining a pair (two) of the single band HF Mobile (loaded) tuneable-tip antennas above, you can have an ideal, single element, horizontal dipole (beam). This type antenna opens the world of HF communications for the apartment dweller, RV HAM, field-day operating, and a variety of other uses and applications.  The packages described below include two antenna, the Double Antenna-Bracket (DBLBRKT), and mounting hardware

$ 39.97 DBLSPCL (without BALUN) With BALUN, see "DBLCOMBO", below.
 75 Meters→,    40 Meters→,    20 Meters→,

17 Meters→,    15 Meters→,    10 Meters→,

 

 6 Meters →                       

We accept:

American Flag, BUX COMM PEN  Has our name, address, and web page address embossed on it.  Keep our web page address handy.

FREE with purchase of $100 or more.

RASCAL Wired-tested RASCAL KIT RASCAL GLX Setup TNC to Radio Cables BASE Antennas MOBILE Antennas BALUNS & MORE AF Cables & Connectors Coax Connectors Antenna Wire & Cable PowerCords-Connectors Tools & Test Equipment Antennas/Accessories The WINDOM antenna RV Antenna/Beam PC CBLs & Connectors Speakers & Mounts Build a G5RV Antenna Fuses & Holders Switches & Relays HAM Microphones CB Microphones Toroids-RFI Suppress BUX PSK31 PRIMER RASCAL to ECHOlink Hum & Noise Solutions RFC Index MISCELLANEOUS IC 706 to ECHOlink HAM Site Grounding Antenna Handbook METERS RF & DVM Accessories.htm Jpole Basics Jpole, 1958 J-pole, tuneable J-pole Up Close J-pole Calculator 9600 Baud Mods GE Pheonix 9600b/s GE Pheonix 1200b/s GE DELTA 9600b/s GE DELTA 1200b/s MICROPHONES TNC WIRING TNC to PC Comports Volume Cntrls & Pots Cables, ETC BUXTERM Pkt Program Solar Power for HAMs Bargain Basement Packet Networking X1J4 Node Setup X1J4 NodeCode SysOP Node Help PacketRadio Primer Packet Glossary PACKET Band-Plan SoundCard FreeWare Connector Heaven Ship & Return Policy H O M E DEALERS NOTICE Mail-FAX OrderForm Fall 2005 Catalog BUXCOMM USA LEGAL STUFF 1 minute load ALL

Order Line ONLY, Mon > Fri 10 AM to 4 PM,  434 534 8873  or FAX your order, 24/7 to FAX 434 525 7818

Hit Counter

CLICK HERE to download RASCAL GLX to REPEATER interface Instructions via EchoLink

 

For Quantity Quotes or Dealer Pricing;

 

Shipping/Handling & warranty Return policy
   * "RASCAL"  is  Registered trademark ®™ of BUX Communications Corp (BUX CommCo ™) 
*(RASCAL™® "Radio And Sound Card Adapter Link")