www.BUXCOMM.com Amateur Radio Base And Mobile, Antennas And Accessories

$ 6.95 each

Dual Band Magnet Mount Antenna 14.95 Low-cost, high quality, dual band antenna with magnetic mount. Ideal for commercial two-way and HAM Radio VHF/UHF FM mobile applications. 200 watt rated.

DBMM 14.95

Use this mast-mounted bracket for 'fixed-station', field-day operating, apartment dwellers, or the mobile RV ops.
With two of our mobile HF antennas you can have the best of both worlds. It is ou an ideal, single element, horizontal dipole (beam). Shown mounted on 1 & 1/4" mast. Dual antenna bracket only, antenna(s) Not Included.

See BUX HF STIX below

DBLBRKT $14.95

BLACK CABLE TIES - 100pcs
.99 Pk of 100
Colour: BLACK (UV Resistant)
Dimensions (A x B): 98 x 2.5mm
Quantity: 100 pcs per/Pak
Material: polyamide (nylon 6.6) as specified in MIL-S-23190 self-extinguishing.
Temperature: -40°F to 230°F
Tensile strength = 18 pounds
A = 4 inches

.99 / Pak of 100
Order : KTFB3

Great for HandHelds
and it is ideal for use
as a rapid-deployment
antenna.

order VM101
$ 12.59

Number 14 TW/AWG with 41 strands of tinned copper wire, Poly-Vinyl insulation covered flexible, but strong. The most preferred wire type when building Dipole's, Windom's, and other flat-top HF antennas. The PVC insulation gives added strength to the 41 strands of tinned, copper wire. Specification: Finely stranded tinned copper conductor (Type III), 105ºC   600 volt copper. 1.5lb/100 Color coded PVC insulation, Temperature range -20°C to 105ºC, Voltage rating 600 volts, Reistant to Acid, Alkilis, Abrasion, Flame, Gasoline, Oil, Ozone, Moisture, Fungus.
100 ft, $19.95 10014 ;   200 ft, $38.95, 20014
300 ft, $57.95 30014 ;   400 ft, $76.95 40014

100 feet of RG-8U Low-Loss, Base-Station Coaxial Cable. It's low loss design and 97% or better shield makes it ideal for this application. GOLD PL-259 coax connectors are installed on each end

50 feet of RG-8U with 97% shielding, Low-Loss, Base-Station Coaxial Cable.
ORDER: RG8PL1L
$39.97 Both ends are fitted with "GOLD" plated PL259/7506 connectors !
100 feet of RG-8U, with 97% shielding, Low-Loss Base-Station Coaxial Cable.
ORDER: RG8PL1C
$59.97

50 Ohm impedance, 3ft, 6ft, 9ft, 12ft,18ft, 50ft & 100 feet.
These jumpers are made from high quality, low-loss, Belden coax cable with Amphenol PL-259 connectors installed.
Three ft. (3') ORDER No.      8X3PLPL $3.99
Six ft. (6')         ORDER No.      8X6PLPL $4.99
Nine ft. (9')      ORDER No.      8X9PLPL $5.99
Twelve ft. (12') ORDER No. 8X12PLPL $7.99
Eighteen ft. (18')ORDER No. 8X18PLPL $8.99

Fifty ft. (50') ORDER No. RG8X50PLPL $22.95
One Hundred ft. (100') ORDER No. RG8X100PLPL $34.95

BUX HF STIX

BHF75M 75 METER 3/8" X 24 THREAD 8 feet long $16.95

BHF40M 40 METER 3/8" X 24 THREAD 8 feet long $16.95

BHF20M 20 METER 3/8" X 24 THREAD 8 feet long $16.95

BHF17M 17 METER 3/8" X 24 THREAD 8 feet long $16.95

BHF15M 15 METER 3/8" X 24 THREAD 8 feet long $16.95

BHF10M 10 METER 3/8" X 24 THREAD 8 feet long $16.95

BHF6M 6 METER 3/8" X 24 THREAD 5 feet long $16.95

These two-piece Mobile antennas consist of a hollow fiberglass base section approximately 1/2 inch diameter with the loading coil wound directly on the fiberglass and covered with shrink tubing. The chrome plated brass base fitting has 3/8 inch X 24 threads that fit the amateur standard 3/8" X 24 mobile mount.

Replacement, 48 inch Tips for above tuneable-tip antennas.    TIP48, $2.95     →     →

BUX stix HF antennas for Mobile and Base Applications:
Power Rated at 250 Watts P E P;   Typical 2:1.VSWR band width is:

·        75 meter: 40 KHz.         40 Meter: 60 KHz.
·        20 Meter: 150 KHz.      17 Meter: 175 KHz.
·        15 Meter: 200 KHz.      12 Meter: 300 KHz.
·        10 Meter: 500 KHz.        6 Meter: 1000 Khz.

TUNING INSTRUCTIONS:
Insert the whip into lower section ferrule about four inches (as shown at right) and tighten set screw. Assemble with fiberglass lower section (as shown at left). Install a VSWR meter at the transceiver and apply 10 to 25 watts of power. Adjust the VSWR meter and output frequency for lowest VSWR reading, indicating resonance. If resonant frequency is too high, loosen set screw and extend top whip until desired resonant frequency is found. If resonant frequency is too low, loosen set screw and adjust whip further into lower section. For best results, adjustments should be made in small increments.

CAUTION: If required, cut off the bottom of the whip to ensure it does not extend down into the coil of the antenna. Failure to observe this precaution will cause heat damage and void any warranty. At resonance, VSWR should be 1.5:1 or less when properly matched. When tuning is complete, tighten set screws securely. NOTE: Bandwidth and VSWR will vary due to mounting location. If your installation has a VSWR over 1.5:1 at resonance, or you need to operate over a greater bandwidth a tuner may be required.

DBLSPCL (without BUX UNUN (ONION)

When the stations with the gain and power in their antennas are transmitting in the horizontal plane, then you should be meeting them in the same plane. Horizontal signals tend to follow the earths contour, and are easier to capture using a horizontally polarized antenna. See the BUX UNUN elsewhere on this page.

By combining a pair (two) of the single band HF Mobile (loaded) tuneable-tip antennas above, you can have an ideal, single element, horizontal dipole (beam). This type antenna opens the world of HF communications for the apartment dweller, RV HAM, field-day operating, and a variety of other uses and applications. The packages described below include two antenna, the Double Antenna-Bracket (DBLBRKT), and mounting hardware. $ 39.97 DBLSPCL (without BUX UNUN (ONION)
75 Meters→, 40 Meters→, 20 Meters→,

17 Meters→, 15 Meters→, 10 Meters→,

6 Meters →

BUX Double Combo "with" BUX ONION (UNUN).
By combining a pair (two) of the single band HF Mobile (loaded) tuneable-tip antennas above, you can have an ideal, single element, horizontal dipole (beam). This type antenna opens the world of HF communications for the apartment dweller, RV HAM, field-day operating, and a variety of other uses and applications. The package described here include: two antenna, the Double-Bracket (DBLBRKT), mounting hardware, and BUX BALUN (UNUN).
$AVE, BOTH, DPLSPCL & BUXUNUN, for only $ 54.97, ORDER, DBLCOMBO
75 Meters→, 40 Meters→, 20 Meters→,

17 Meters→, 15 Meters→, 10 Meters→

6 Meters →

DUAL BAND, HIGH GAIN, BASE STATION ANTENNA, UVS-200
6.7 db @ 2 meters, 8.2db 70cm. High Performance, High Gain, Dual Band, Base Station Antenna 5/8 wave, vertical stacked collinear design 2-5/8 elements on 2mt., 4-5/8 elements on 70cm. 6.7 db @ 2 meters and 8.2 db 70cm. Superior wideband performance Heavy duty fiberglass radome Durable, waterproof joints Mounting Hardware included Accepts standard PL-259 connector 200 Watt power rating Radiating element, 100 inches. DC ground, enclosed elements reduces terrestrial noise.

~~Reg $109.95~~ BUX COMM price, $57.97

UVS-200

Description:

2M/70CM DUAL BAND FIBERGLASS VERTICAL GAIN GROUND PLANE ANTENNA

HIGH PERFORMANCE , HIGH POWER RATING, LOW SWR AND BROADER BAND COVERAGE ON BOTH 2m AND 70cm BAND.

SPECIALLY DESIGNED TO KEEP THE ANTENNA STRAIGHT AS ONE ELEMENT.

USING RING GASKET MAKES ANTENNA PERFECTLY WATERPROOF.

EASY ASSEMBLY JUST BY TIGHTENING THE JOINT ACCORDINGLY.

INSULATED CONDUCTOR, LESS INTERFERENCE FROM RAIN, SLEET AND SNOW. REDUCED PRECIPITATION STATIC, LOWER BACK GROUND NOISE.

DC GROUND DESIGN LEADS THE HIGH VOLTAGE CAUSED BY THUNDER AND LIGHTENING TO THE GROUND, PROTECTS RADIO EQUIPMENT.

ACCEPTABLE MAST DIAMETER 30-62m/m (1-3/16" 2-7/16")

SUPPLIED WITH MAST BRACKET, V-BOLT, SUPPORTT TUBE AND ALL MOUNTING HARDWARE.

ELECTRICAL SPECIFICATIONS: LENGTH 2.5m (98.4"), GAIN 2m 6dB/70cm 8dB, CONFIGURATION 2m 5/8 WAVE 2-ELEMENT/70cm 5/8 WAVE 4-ELEMENT, FREQUENCY 144~148/435~450 MHz, MAX POWER 200 WATTS, IMPEDANCE 50 OHM, V.S.W.R LESS THAN 1.5:1, CONNECTOR SO-239 (UHF).
~~Reg $109.95~~ BUX COMM price, $57.97
UVS200

VH2201 VHF BASE & REPEATER Antenna.
Frequency Range:
136-174 MHz
Gain: 4.5dB
VSWR less than 1.5:1
Power Rating: 200 watts
Impedance: 50 Ohms
Stainless Steel Radials
SO-239 Input connector
Radiating element Length 6 feet.
Built to Commercial standards for base station installations,
and rugged, mountain-top repeater applications. Mounting
hardware and stainless-steel radials included. Ship wt, 5 Lb

$47.97 VH2201

UH2401 UHF BASE & REPEATER Antenna
Antenna Frequency Range: 430-490 MHz
Gain: 6.5dB
Power Rating: 200 watts
Impedance: 50 Ohms
Stainless Steel Radials
SO-239 Input connector
Radiating element
length 5 feet. Built to Commercial standards for base station installations, and rugged, mountain-top repeater applications. Mounting hardware and stainless-steel radials included. Ship wt, 5 Lb

$47.97 UH2401

"Vertical" Six Meter Ground Plane

All mounting hardware and assembly instructions are included.

Also includes cutting chart for exact frequency measurements.

Solid Hard-Drawn Aluminum GP6M $49.95

Two meter "Vertical" VHF Ground Plane
All mounting hardware and assembly instructions are included.

Also includes cutting chart for exact frequency measurements.
Solid Hard-Drawn Aluminum GP146 $34.95

Dual Band, 2 meter (144 mHz) & 70 cm (440 mHz)
"Vertical" VHF & UHF Ground Plane
All mounting hardware and assembly instructions are included.

Also includes cutting chart for exact frequency measurements.
Solid Hard-Drawn Aluminum GP146440 $44.95

VHF and UHF 'Cross-Needle' High
Performance, SWR & POWER Meter.
For the serious VHF/UHF operator, here is a 140 to 160 MHz & 440 to 480 MHz, VSWR and POWER meter with; 10 - 100 - 1000 watt scales.

SWR-6 $69.95

SWR & WATT METER 100 watt & 10 watt level switch This is a handy, compact meter designed for the amateur radio operator. Test antenna performance and transmitter operation, 1.7 to 50 MHz. May also be used as a RF field strength meter and to check QRP.

SWR-3, $19.95

The perfect QRP SWR and Watt Meter.

SWR: 1:1 to 1:3;      RF Power: 0.5~10W;     Accuracy: =SWR: +- 5%
Power: +- 10%;        Impedance: 52 W,         Meter Sens. 200uA
                                  Freq. Range 1.7 to 30MHz

QRP, SWR & POWER Meter, (0.5 to 10 watts) with SO 239 connectors.

SWR-2T, $12.99

Important Information; WHY USE A 4:1 BALUN

Krusty Olde Kurt is now going to repeat himself. Why? Because the same question keeps coming up over and over. And he wants everyone to get it right. "I'm feeding my dipole with 600-ohm line. At the station end I need a balun to convert to 50-ohm coax. I need a 12:1 balun, right?" Wrong! A 4:1 balun would be better. Why is that? If your dipole is up, let's say, 35 feet then on 80 meters it will probably have a resistance at resonance of about 40 ohms. The actual resistance depends on the height above ground in wavelengths.

If the dipole is 40 Ohms then what do you see at the transmitter end of your 600 ohm line? If the line is a half-wave long (120 ft on 80 Meters) you'll see 40 ohms. Remember, a half-wave line repeats what it sees at the other end. But if it is a quarter-wave long you'll see 8500 Ohms! At other line lengths you'll see impedances somewhere between these two extremes. So you are not going to see 600 ohms at the end of your 600-ohm line. That only happens if you have a 600-ohm antenna hooked onto it. With such a variation in impedance at the transmitter end of the line there is no one balun transformer that will match it. Most of the time the impedance will be above the 50 Ohms of your coax so a high impedance balun would be desirable. Unfortunately high impedance baluns don't work well when not matched.

Experience has shown that 4:1 baluns work best in this service. They are more rugged and will take bad mismatches especially if they are wound on an iron powder core. So stop searching for that 12:1 balun. Use a 4:l BALUN and your system will work great.
You can read Kurt N. Sterba “AERIALS” column in World Radio Magazine.

BUX ONION $19.95 "Decoupling Transformer"
BUX UN UN De-Coupling transformer, has SO-239 (female) input connector and output connector is 1 ft Mini 8 cable with PL-259 (male). BUX ONION is an UNbalanced to UNbalance (UN-UN) decoupling transformer designed to be used by the Apartment dweller or the RV ops. It is also used with the DBLSPCL antenna. High RF currents traveling along the coax feed-line shield can cause high VSWR. This decoupling transformer prevents RF currents from traveling down the outer shield of the coax. The input connector is an SO239 (female) and the output connector is a PL259 (male).

BUX ONION $17.95

BONUS SPECIAL ! Buy either of our 4:1 HD ⁭ or our 1:1 HD ↓ BALUNs and receive "FREE," three of our "high-dielectric" White, TyNyte, Insulators

With an increase in local noise sources and the increasing attractiveness of long wire and dipole antennas, coax cable has become the antenna feed line of choice for most radio users and operators. Given that the impedance of most commonly available coax is either 50 or 72 ohms and since many wire antennas present an impedance of 200 to 600 ohms or more at the feed point, direct connection of the coax to wire antennas hits us with a significant signal loss due to the antenna impedance mismatch. Having realized this set of circumstances in the receiver and SWL arena, we're introducing a new approach to defeat the noise and impedance mismatch problems in our receive antennas by designing this new RxBALUN™. Our RxBALUN™ bridges the impedance gap, and enables an unbalance to balanced match between the antenna and our receivers. These features provide more signal transfer from the antenna to your receiver.

Our RxBALUN will accommodate the SWL and QRP Operator. In addition, this RxBALUN may be employed as an antenna balun for both transmit and receive between the antenna and low powered transceivers running up to 200 watts. For input and output connectors, we use only the best Silver plated, Teflon®™ insulated, SO239 connectors. Max Power 250 watts
14.95 RxBALUN

Stainless eyebolt is inserted into Tenyte "Center Insulator" The "Center Insulator" is used to suspend the center of a Dipole, Windom, or other wire type antenna from tower, tree, or support structure.

1.99 Stock# CIA

Center Insulator and two end insulators 3.99 Order CIAX3

For the apartment dweller, you can now hang the 20 meter doublet in the attic. I've QSO'd with stations all over the world with the 33 ft dipole in the attic of my garage. One insulator at the center, and one each end. It's great for other HF WINDOM and or dipole antenna. Dielectric strength is better than the old ceramic insulators, but without susceptibility to cracking or breakage under impact or extreme temperature changes.
Package of 3, $2.99 Antenna Insulators
Package of 10, Insulators $8.99, ANTINSLX10

A METHOD TO HANG

YOUR BALUN.

CLICK ON THUMBNAIL

AT RIGHT TO

VIEW FULL SIZE

DRAWING.

Dipole and inverted-Vee antennas are commonly "balanced" at the feed points. Coaxial feed lines are "unbalanced" by design personality (thus the name BALUN). This BALANCED, to UNBALANCE marriage can only be performed by using a BALUN. A BALUN should always be used when feeding wire antennas with coax to make certain characteristic antenna performance and optimum transfer of RF energy to the antenna complete.

When coax is used to feed antennas without the benefit of a BALUN, current flows on the shield of the coaxial feed line . This coaxial shield current can produce a "Hot HAM shack," This can result in nasty R.F. injury from the microphone to lips, hand key to fingers, etc., and is often more pronounced at certain frequencies. Coax cable shield currents can also cause damage to your HAM gear.   TVI, RFI, telephone and even wild VSWR indications can result from these shield currents.

In 85% of antenna projects that displayed these problems, when a BALUN is added to the coaxial line or near the antenna feed point, these problems were diminished or completely eliminated.

At BUX COMM, *We don't cut corners! The components used in the manufacture of our BALUNs are from top quality components, beginning with the Silver Plated SO239 connectors and center insulator made of teflon™(E.I Dupont), and the center pin is hard-drawn brass, with gold flash. The wire we wind the ferrite donut with, is heavy-duty, silver flashed wire, with teflon™ insulation, which will handle RF voltages above 5000 volts, and temperatures above 2000 degrees. The binding posts are heavy-duty, tempered brass, with end holes and side-thru holes to accommodate either type loop-thru connection. A double-shoulder brass capture nut is used to add a secure bite and improve electrical connections to the wire .

In addition, these Antenna connection points are clearly identified with "RED" and "BLACK" rings to denote the "hot" and "cold" terminals... just in case you want to favor the highest or longest side of your antenna.

The Duplexer shown here is the ideal companion for our Dual-Band, Base Antennas ! HF and VHF/UHF Antenna Duplexer (Indoor use)

Frequency: (Port 1) 1.3 - 225 MHz, (Port 2) 350 - 540 MHz
Power:       500 W 1.3 - 35 MHz,    300 W 50 - 540 MHz
Insertion Loss: <0.2 dB Isolation: 60 dB;    VSWR: < 1.2:1
Combine HF/6m/2m output (Port 1) and your UHF output
from your transceiver and send to one antenna.

$34.95 Order DU-500

Specifications:

Frequency Range: Up to, and including 600 MHz
VSWR: Below 1.2:1
Power Rating: 1.5 kW peak 1kW continuous
Impedance: 50 Ohms
Insertion loss: Less than 0.2 dB.
Port Isolation: Better than 50 dB.
Port connectors: SO-239

One IN, Two Out, and
May be configured Two IN, One Out.

2 Position Coax Switch

CX-201 $19.95

GOLD LINE 2 POSITION Antenna Switch
Switch between Beam, and HF wire antennas, or between VHF/UHF and HF Beams. RATED AT 1 kW.

GL1048 $ 9.95

Antenna Coax Switch; 1 IN, 3 Out, in Metal case.
Antenna Coax Switch; One IN, Three Out, or Three IN, and One OUT, 50 Ohm impedance, 3 port to 1 port Antenna Switch. Rated at 1 KW, SO-239 ports, mounted in metal case.

CX3 $9.95

HandHeld "HR-9" Duckie

Frequency: 144 - 148 MHz

SWR: Less than 1.5:1

Connector: BNC Male

Length:   4 inches, or 105/mm

9.95 HR-9

HR-601VU
VHF & UHF Antenna

Dual-Band, HandHeld antenna, with SMA male connector for use with late model transceivers

12.95 HR-601VU

HR-601V is for VHF only handheld transceivers.

Frequency: 144-148 MHz
VSWR: Less than 1.8:1
Whip is Shape/Memory Alloy
Connector: SMA Male

10.95 HR-601V

NMO Antenna Mount RAIN CAP.
Used to cover the NMO mount when not in use. Comes in basic gloss black.
The NMO cover with built-in "0-Ring" seal.

                .99 ea, Order NMO5

HOLE PLUGS Drilled the hole in the wrong place? Removed an old base-loaded antenna;    This black rubber plug is inserted into the hole to seal from moisture. It can be painted to blend color.

The profile is about 1/8 inch high when inserted,

Plug for 3/8" hole .99                Plug for 1/2" hole .99

Plug for 5/8" hole .99                Plug for 3/4" hole .99

Plug for 7/8" hole .99                Plug for   1" hole   .99

This NMO Hole Mount will fit into a 3/8" hole, or use the adapter (included) to adapt it to a 3/4" hole. The BUX CommCo NMOH is supplied with 17 ft of 98% shielded RG-58 cable terminated into a PL-259 UHF connector. Cables are attached at right angles to the mount. Mounts also include a built-in seal around the mounting hole to protect from moisture. AM-207B $8.95

Trunk Lip, NMO Mount, model AM-209 is a trunk-lip mount supplied with 14 ft of RG-58 cable, a PL-259, and the industry standard NMO mount. The AM-209 mounts on a standard trunk-lip and comes with 14ft of cable terminated in a PL-259.

     AM-209 $11.95

NMO mount only. For virgin installation when cable is already in place. No cable, only the NMO mount. Hardened Brass.

$4.95 NMO-2

ANTENNA ADAPTER
3/8"x24 thread base antenna to NMO Mount

When you don't care to drill another hole for that whip, or new antenna, this heavy-duty adapter mates a 3/8"x24 thread antenna base to an NMO mount.   Also includes "O" ring-to-body, seal to prevent moisture oxidation.

    NMO-6 $8.95

NMO to SO239 Antenna Adapter
When you don't care to drill another hole for that whip, or new antenna, this heavy-duty adapter mates a SO-239 (PL259 type) antenna base to an NMO mount. Also includes "O" ring-to-body, seal to prevent moisture oxidation

.
$8.95 NMO8

Dual Band, Trunk Lip Mount, Antenna
Trunk Lip Mount has steel lip clamp and dual set-screws. With standard 3/8" X 24 thread base. Pre-wired with 17" of RG-58 to BNC Connector. Black rubber paint protector, see photo. Includes a PL-259 adapter/connector

$16.98 TLM7519

"The Adapter" is the best way to describe it ! Our number one seller when it comes to antenna adapters.

$ 2.99 each Order 7060

BNC male to UHF Female $2.99 ea

WINDOW CLIP for HT or SCANNER ANTENNA
SMA window antenna clip $10.95 AM 800

BNC window antenna clip $11.95 AM 801B

SMA or BNC "HAT" Clip-on Mount
SMA $10.95, AM 550

BNC Hat Clip $11.95 AM 551

Your BUX BALUN is warranted against defects in components or construction for a period of three (3) months from date of purchase. Our warranty does not cover damage due to misuse, abuse, or nonessential operation outside the specifications of the BUX BALUN. This warranty applies only to the original purchaser. A copy of the receipt showing the purchaser’s name and the date of purchase must accompany BALUN's returned for warranty service or replacement. All returns must be shipped prepaid.

Should there arise a requirement to return your BUX BALUN for service, carefully wrap and package it. We will re-use your carton to return the BUX BALUN to you. Be sure to include your return address. Include a full description of the problem, along with your name, address, phone number and/or e-mail address. Repairs average approximately 3 to 4 days.

QUAD MAGNET, Antenna Mount.
Available in; Triple Chrome Plate, or Basic Black. You asked for strength in a super mobile antenna mount, and WE DELIVERED ! Features 4, five inch Heavy-Duty magnets, equally spaced on a Heavy Duty, 1/4" thick, hard-drawn metal frame. The BUX4MM is prewired with 3/8" X 24 threaded (standard) Mount, and PL259 connector. Accepts 3/8 X 24 antennas

$44.97 BUX4MMC "chrome"

$44.97 BUX4MMB "Black"

Right Angle SM1L Mount Right angle stud mount with SO239 coaxial cable connector and a 3/8-24 threaded antenna socket. Great for those cramped areas. Reg ~~11.95~~, BUX COMM Price: $8.88	Pick-Up Truck, Flat-BAR, STAKE HOLE Mount w/SM1	Adjustable Bumper Mount with 3/8"x24 thread SM-1, and SO239 (PL259) input. Both may be used on hatch-back lid-lip, trunk-lip, bumper & hood.
$ 6.95 each	$19.95	442 S $16.95


BUMPER MOUNT with SO239 input connector, accepts PL259. $9.95 Order 422-S
422S $9.95	Ball Mount with SO-239 (female) connector, AM601S $11.95	Ball Mount with terminal lug connection, AM601L $11.95


Heavy Duty Spring for Whips up to 102 inches.	Often called the mobile antenna, Kwik-Disconnect This Mobile Antenna Adapter... is a 'SNAP' to change antennas or bands in a matter of seconds	Set of five (5) Kwik-Connect Antenna adapters and snap-on stud. Make changing mobile antennas a 'SNAP!' with a set of 5 ''Kwik Disconnect'' adapters.
S55S $8.95	KD3 $5.95	KD5 $15.95 Set of 5.

HandHeld "HR-9" Duckie Frequency: 144 - 148 MHz

ANTENNA INSULATORS

HandHeld "HR-9" Duckie

Frequency: 144 - 148 MHz