MOBILE Antennas for HAM Radio and 2-way commercial radio

Tell your friends, you found it at:

Serving Telecommunications and HAM Radio since 1969
Monday thru Friday; 9:AM to 4:PM, Eastern toll-free OrderLine: 1 866 300 1969
Saturday, 12 noon to 6 pm Eastern Toll Free, ORDERS ONLY 1 800 726 2919
We Accept;

DEALER'S, SPECIAL ANTENNA DISCOUNT

WAS ~~29.98~~, now half price; $14.95

Dual Band, 144-154 MHz & 440-460 MHz Trunk Lip Mount, Antenna Trunk Lip Mount has steel lip clamp and dual set-screws. With standard 3/8" X 24 thread base.   Pre-wired with 17ft of RG-58 to BNC Connector.
Black rubber paint protector, see photo.   Includes a PL-259 adapter/connector
$14.95 DBTL270

Trailer Hitch Mount with 7/8" hole for mounting with trailer-hitch ball, bolt. for antennas with 3/8" X 24 (standard) antenna base. Stainless steel with SO239 coax fitting to receive PL259 coax connector. Also accepts the BUX HF STIX shown above. Stock number THM1 $ 11.95

$ 17.95

NOTE: The UHFH239 (SO239) mount at right,→
is easy to replace the NMO connector in the above stake-hole mount.

Ideal for: Campers. RV's, trailers, boats, and fender mounting where small metal ground plane area is available. $3.95 each
Order UHFH239

$19.95

Pick-Up Truck, Flat-BAR, STAKE HOLE Mount with SM1 for 3/8" x 24 thread base antennas.

←

CARDINAL

←BUX Master-Match™ Balun 1:1 $24.95 MM11

BUX Master-Match™1:1 Baluns are ideal for Dipoles, Slopers, Inverted-Vees and center feed-point, RV antennas. They are also employed at the driven element of of many HF beams and Quads, and where feedpoint impedance is at, or near 50 ohms. By equalizing the currents in the antenna feeders, the Dipole pattern improves and prevents feedline (re)-radiation by preventing antenna currents flowing along the outer braid of the coax transmission line. BUX BALUNS are equipped with eye-bolts for easy support and suspension. Includes three FREE antenna insulators (shown elsewhere, this page).

BLACK HAWK

←BUX Master-Match™ Balun 4:1

$19.95 MM41

Our BUX Master-Match™4:1 Balun is ideal for matching windoms, web'd or folded dipoles, and antennas fed at a 250 ohm to 500 ohm impedance feedpoint with normal 50 or 75 ohm coax cable. In contrast to ordinary Baluns the BUX Master-Match™4:1 Balun support balanced currents in each leg of the antenna and prevents feedline (re)-radiation. As mentioned in our windom articles, feedlines and 450-ohm, brown, poly-covered ladder-line are easy to handle, and more-over they present another efficient means to feed multi-band antennas. We strongly suggest the use of our PolyCoat-Ladder-Line as it is made of strong, copper-clad, steel conductors. This light but durable, PolyCoat-Ladder-Line will far outlast the normal open copper with plastic spacers. BUX BALUNS are equipped with eye-bolts for easy support and suspension. (Includes three FREE antenna insulators, shown elsewhere, this page).

The Got’cha is; These open type feedlines can bring high RF voltages into the shack. By using BUX Master-Match™4:1 Balun near the point where the transmission line enters the HAM shack, we impede that lip-bitting voltage and prevent excessive RF from getting into the PC, the transceiver, the telephone, the television (the XYL is watching) and heaven-forbid, the computer on her automatic washer.

AMERICAN EAGLE

2500 WATT BALUN
This is our BUX COMM High-Performance, Heavy Duty, "Big Talker"
We designed it to cope with a "couple" kilowatts... or three. We decided that was NOT good enough, so we built it to endure harsh treatment.
STATS: Current Balun, Wt. 1.5 LBs, 4:1 Hi-Power, 1.8 thru 30 MHz
HEAVY DUTY TOROID MADE OF TYPE 43 FERRITE, FOR LOW PERMEABILITY
2500 WATT 4:1 current High Performance, Heavy Duty,
SSB/CW Power @ 3.5 MHz* >2.5kW * SWR is less than 3:1, Not rated for RTTY & AM
Will not saturate at Amateur Radio Power Levels ~~Regular $64.97~~
Order AE41 $ 34.95

1:1 version High Performance, Heavy Duty, 2500 WATT (Current BALUN),
Order AE11 $ 34.95

BUX BALUNS are equipped with eye-bolts for easy support and suspension.

BUX COMM Antenna UNUN
For bottom fed, and Screw-Driver antennas.
1.8 MHz to 52 MHz
Master Match
"Big Talker" UNUN
FREE RG8X coax jumper with PL259's attached, INCLUDED!

o FREE RG8X coax jumper with PL259's.
o 1.8 to 52 MHz
o Ferrite (current) Broadband Toroid design
o Heavy Duty, Lightweight construction
o SO-239 UNbalanced input.
o SO-239 UNbalanced output,
o Sealed against moisture

BUX ONION $19.95
"Decoupling Transformer"
BUX UN UN De-Coupling transformer, has SO-239 (female) input connector and output connector is 1 ft Mini 8 cable with PL-259 (male). BUX ONION is an UNbalanced to UNbalance (UN-UN) decoupling transformer designed to be used by the Apartment dweller or the RV ops. It is also used with the BUXcomm DBLSPCL antenna.

High RF currents traveling along the coax feed-line shield can cause high VSWR. This decoupling transformer prevents RF currents from traveling down the outer shield of the coax.

EGG "strain" type ceramic, 1-3/8" insulator. Used as antenna end insulators, and for breaking up resonant or "Hot-Tower" guy wires.

3 for 1.99 Order 3EGG

Large EGG "strain" type ceramic, 2" insulator. Used as antenna center and end insulators, and for breaking up resonant or "Hot-Tower" guy wires.
3 for 2.99 Order LEGG

Keep your RF Power at your antenna.

When operating mobile, every watt your transceiver sends is valuable. Add the BUX !:! and prevent high VSWR. By installing the BUX UNUN near the input to your antenna, you deliver more RF energy to the antenna, and reduce the re-radiation of RF back onto the shield of your coaxial feedline. More power is delivered directly to your antenna.

High power rating, Low-permeability toroid, with Internal fiber-glass composition to prevent unnecessary vibration during mobile operation.

For input and output connectors, we use only the best Silver plated, Teflon®™ insulated, SO239 connectors, and Amphenol PL259, with the heavy duty RG8X to connect to the input of your antenna. Power rating of our BUX UNUN is 1000 watts. Our UNUN is also ideal for marine antenna installations.

$19.95 V BALUN

Teflon ®™ E I DuPont corp.
Amphenol ®™ TYCO Corp.

BUX BALUNS are equipped with eye-bolts for easy support and suspension.

* 1/4 wave on 2 meters * 2.5 dBi gain at 440 MHz. * Rated at 200 Watts * 12 ft of RG-58 cable with *PL-259 connector.
* Magnet mount designed for winds of 100 mph * Overall height is 21 inches.

$17.95 VU1510

Same as shown at left, but has *BNC connector for use with hand-helds with BNC antenna input. $18.95 each ORDER
VU-1510-"B"

$18.95 VU1510B

5/8 wave antenna,
136 - 174 MHz
NMO Base
(Mount not included)
39 inches overall
VSWR less than 1.5:1
200 Watts

VH-1215 $16.95

5/8 wave antenna,
220-265 MHz
NMO Base
(Mount not included)

VSWR less than 1.5:1
200 Watts
220-265 MHz version PM220 $21.95

PM220 $21.95

$VU-1545 17.95

Recommended Mag Mount is AM-1045 B, NMO Mounts shown here. Get both, the VU1545 VHF/UHF (NMO) Antenna & the AM-1045B, 5 inch, Super Heavy-Duty
Magnet Mount for $29.99
BOTH 1545 &1045
for $29.95

BLACK CABLE TIES - 100pcs
.99 Pk of 100
Colour: BLACK (UV Resistant)
Dimensions (A x B): 98 x 2.5mm
Quantity: 100 pcs per/Pak
Material: polyamide (nylon 6.6) as specified in MIL-S-23190 self-extinguishing.
Temperature: -40°F to 230°F
Tensile strength = 18 pounds
A = 4 inches

.99 / Pak of 100
Order : KTFB3

140 - 170 MHz VHF
Economy Mag Mount Antenna.
Order 2MMM 11.95

Need a High Quality jumper from your transceiver to the linear? A HiQuality coax jumper for that transceiver Output to linear input! The connectors are Amphenol™ and coax is RG-8X by Belden. Hi Quality, Six ft. (9') jumper made using high quality components
$6.97 HIQ9JMPR

Remember the axiom; 'An ounce of prevention is worth a pound of cure.' This lightning protector contains a modified spark gap that provides that ounce of prevention. . Remember, there is no substitute for a good earth ground, AC line surge, and spike protection. Where lightning is involved, we make no warranties. We offer the 7516 as a secondary lightning protector. Ground wire attached to wire lug. $ 4.99 ea Stock # 7516
STORM SEASON is just around the corner. It pays to be prepared !
$ 4.99 ea

Kit contains:
2 - Adhesive Pads
1 - Alcohol Surface Cleaning Swabs
1 - Trim Plate
1 - Shrink Tube
REMOUNT KIT for all TG Series (Thru-Glass) Antennas.
REMNTKIT 5.97

$ 6.95 each

Dual Band Magnet Mount Antenna 14.95 Low-cost, high quality, dual band antenna with magnetic mount. Ideal for commercial two-way and HAM Radio VHF/UHF FM mobile applications.
Power Rating, 200 watts.

14.95 DBMM

Ideal for: Campers. RV's, trailers, boats, and fender mounting where small metal ground plane area is available. $3.95 each
Order UHFH239

.99 / Pak of 100
Order : KTFB3

For all type of outdoor antenna connections, BALUNS, Coax connectors, coax bulkhead entry panels and more. Use Coax-Seal® to protect any outdoor connection or connector. Coax-Seal is made of a non-conductive, non-contaminating waterproof material that remains flexible at any temperature from -30° to 180°F. Coax connectors that are not waterproof or have exposed solder joints can weaken from oxidation !

Coax-Seal is superior to electrical tape or vinyl sealants for moisture protection.

Each box of Coax-Seal contains (60 inches x 1/2 inch) five feet and will protect ten (10) connectors.

2.95 Order Code CS104

2.95 Order CS104

RG213
Low-Loss, Base-Station Coaxial Cable. Ultra low loss design with double shield makes it ideal for this application. PL-259 coax connectors are installed on each end

50 feet of RG-213 double shield, Ultra Low-Loss, Base-Station Coaxial Cable. ORDER: RG213PL50 $49.97

Both ends are fitted withPL259/7506 connectors ! 100 feet of RG-213, double shield, Ultra Low-Loss Base-Station Coaxial Cable.
ORDER: RG213PL100 $69.97

RG8U

100 feet of RG-8U Low-Loss, Base-Station Coaxial Cable. It's low loss design and 97% or better shield makes it ideal for this application. PL-259 coax connectors are installed on each end

50 feet of RG-8U with 97% shielding, Low-Loss, Base-Station Coaxial Cable.
ORDER: RG8PL1L
$39.97 Both ends are fitted with PL259/7506 connectors !
100 feet of RG-8U, with 97% shielding, Low-Loss Base-Station Coaxial Cable.
ORDER: RG8PL1C
$59.97

50 Ohm impedance, 3ft, 6ft, 9ft, 12ft,18ft, 50ft & 100 feet.
These jumpers are made from high quality, low-loss, Belden coax cable with Amphenol PL-259 connectors installed.
Three ft. (3') ORDER No.      8X3-PLPL $3.99
Six ft. (6')         ORDER No.      8X6-PLPL $4.99
Nine ft. (9')      ORDER No.      8X9-PLPL $5.99
Twelve ft. (12') ORDER No. 8X12-PLPL $7.99
Eighteen ft. (18')ORDER No. 8X18-PLPL $8.99

Fifty ft. (50') RG8X with PL259 installed on each end ORDER No. RG8X50PLPL $24.95
One Hundred ft. RG8X with PL259 installed on each end ORDER No. RG8X100PLPL $37.95

BUX HF STIX

BHF75M 75 METER 3/8" X 24 THREAD 8 feet long $16.95

BHF40M 40 METER 3/8" X 24 THREAD 8 feet long $16.95

BHF20M 20 METER 3/8" X 24 THREAD 8 feet long $16.95

BHF17M 17 METER 3/8" X 24 THREAD 8 feet long $16.95

BHF15M 15 METER 3/8" X 24 THREAD 8 feet long $16.95

BHF10M 10 METER 3/8" X 24 THREAD 8 feet long $16.95

BHF6M 6 METER 3/8" X 24 THREAD 5 feet long $16.95

These two-piece Mobile antennas consist of a hollow fiberglass base section approximately 1/2 inch diameter with the loading coil wound directly on the fiberglass and covered with shrink tubing. The chrome plated brass base fitting has 3/8 inch X 24 threads that fit the amateur standard 3/8" X 24 mobile mount.

Replacement, 48 inch Tips for above tuneable-tip antennas.    TIP48, $2.95     →     →

BUX stix HF antennas for Mobile and Base Applications:
Power Rated at 250 Watts P E P;   Typical 2:1.VSWR band width is:

·        75 meter: 40 KHz.         40 Meter: 60 KHz.
·        20 Meter: 150 KHz.      17 Meter: 175 KHz.
·        15 Meter: 200 KHz.      12 Meter: 300 KHz.
·        10 Meter: 500 KHz.        6 Meter: 1000 Khz.

TUNING INSTRUCTIONS:
Insert the whip into lower section ferrule about four inches (as shown at right) and tighten set screw. Assemble with fiberglass lower section (as shown at left). Install a VSWR meter at the transceiver and apply 10 to 25 watts of power. Adjust the VSWR meter and output frequency for lowest VSWR reading, indicating resonance. If resonant frequency is too high, loosen set screw and extend top whip until desired resonant frequency is found. If resonant frequency is too low, loosen set screw and adjust whip further into lower section. For best results, adjustments should be made in small increments.

CAUTION: If required, cut off the bottom of the whip to ensure it does not extend down into the coil of the antenna. Failure to observe this precaution will cause heat damage and void any warranty. At resonance, VSWR should be 1.5:1 or less when properly matched. When tuning is complete, tighten set screws securely. NOTE: Bandwidth and VSWR will vary due to mounting location. If your installation has a VSWR over 1.5:1 at resonance, or you need to operate over a greater bandwidth a tuner may be required.

Thru-Glass Scanner antenna. Covers 20 MHz to 1200 MHz. Supplied with 14 ft of coax with connector and mounting materials. Installation instructions and recommended mounting location. 9.95 Order SCANT

VHF and UHF 'Cross-Needle' High
Performance, SWR & POWER Meter.
For the serious VHF/UHF operator, here is a 140 to 160 MHz & 440 to 480 MHz, VSWR and POWER meter with; 10 - 100 - 1000 watt scales.

SWR6 $69.95

SWR & WATT METER 100 watt & 10 watt level switch This is a handy, compact meter designed for the amateur radio operator. Test antenna performance and transmitter operation, 1.7 to 50 MHz. May also be used as a RF field strength meter and to check QRP.

SWR3, $19.95

SWR: 1:1 to 1:3;      RF Power: 0.5~10W;     Accuracy: =SWR: +- 5%
Power: +- 10%;        Impedance: 52 W,         Meter Sens. 200uA
                   Freq. Range 1.7 to 30MHz

QRP, SWR & POWER Meter, (0.5 to 10 watts) Freq. Range 1.7 to 30MHz

SWR2T, $12.99

The Duplexer shown here is the ideal companion for our Dual-Band, Base Antennas ! HF and VHF/UHF Antenna Duplexer (Indoor use)

Frequency: (Port 1) 1.3 - 225 MHz, (Port 2) 350 - 540 MHz
Power:       500 W 1.3 - 35 MHz,    300 W 50 - 540 MHz
Insertion Loss: <0.2 dB Isolation: 60 dB;    VSWR: < 1.2:1
Combine HF/6m/2m output (Port 1) and your UHF output
from your transceiver and send to one antenna.

$34.95 Order DU500

Specifications:

Frequency Range: Up to, and including 600 MHz
VSWR: Below 1.2:1
Power Rating: 1.5 kW peak 1kW continuous
Impedance: 50 Ohms
Insertion loss: Less than 0.2 dB.
Port Isolation: Better than 50 dB.
Port connectors: SO-239

One IN, Two Out, and
May be configured Two IN, One Out.

2 Position Coax Switch

CX201 $19.95

GOLD LINE 2 POSITION Antenna Switch
Switch between Beam, and HF wire antennas, or between VHF/UHF and HF Beams. RATED AT 1 kW.

GL1048 $ 9.95

Antenna Coax Switch; 1 IN, 3 Out, in Metal case.
Antenna Coax Switch; One IN, Three Out, or Three IN, and One OUT, 50 Ohm impedance, 3 port to 1 port Antenna Switch. Rated at 1 KW, SO-239 ports, mounted in metal case.

CX3 $9.95

HandHeld "HR-9" Duckie

Frequency: 144 - 148 MHz

SWR: Less than 1.5:1

Connector: BNC Male

Length: 4 inches, or 105/mm

9.95 HR9

HR-601V is for VHF only handheld transceivers.

Frequency: 144-148 MHz
VSWR: Less than 1.8:1
Whip is Shape/Memory Alloy
Connector: SMA Male

10.95 HR601V

15.5" Dual Band Rubber Duck. Similar in size and performance to the Diamond RH-771.

Frequency Range: 144-148 MHz & 440-450 MHz

VSWR: Less then 1.5:1

Connector: BNC Male

Length: 15.5 inches

$ 17.95 Order HR12DB

HR-601VU VHF & UHF Antenna

Dual-Band, HandHeld antenna, with SMA male connector for use with late model transceivers

12.95 HR601VU

WINDOW CLIP for HT or SCANNER ANTENNA SMA window antenna clip
$10.95 AM800

BNC window antenna clip
$11.95 AM 801B

SMA or BNC "HAT" Clip-on Mount

SMA $10.95, AM550

BNC Hat Clip
$11.95 AM 551

NMO Antenna Mount RAIN CAP.
Used to cover the NMO mount when not in use. Comes in basic gloss black.

The NMO cover with built-in "0-Ring" seal.

.99 ea, Order NMO5

HOLE PLUGS Drilled the hole in the wrong place? Removed an old base-loaded antenna;    This black hard-rubber plug is inserted into the hole to seal from moisture.   It can be painted to blend color.   Add RTV or similar sealer for "perfect seal."

The profile is about 1/8 inch high when inserted,

Plug for 3/8" hole .99                Plug for 1/2" hole .99

Plug for 5/8" hole .99               Plug for 3/4" hole .99

Plug for 7/8" hole .99                Plug for   1" hole   .99

This NMO Hole Mount will fit into a 3/8" hole, or use the adapter (included) to adapt it to a 3/4" hole. The BUX CommCo NMOH is supplied with 17 ft of 98% shielded RG-58 cable terminated into a PL-259 UHF connector. Cables are attached at right angles to the mount. Mounts also include a built-in seal around the mounting hole to protect from moisture. AM207B $8.95

Trunk Lip, NMO Mount, model AM-209 is a trunk-lip mount supplied with 14 ft of RG-58 cable, a PL-259, and the industry standard NMO mount. The AM-209 mounts on a standard trunk-lip and comes with 14ft of cable terminated in a PL-259.

AM209 $11.95

NMO mount only. For virgin installation when cable is already in place. No cable, only the NMO mount. Hardened Brass.

$4.95 NMO2

ANTENNA ADAPTER
3/8"x24 thread base antenna to NMO Mount

When you don't care to drill another hole for that whip, or new antenna, this heavy-duty adapter mates a 3/8"x24 thread antenna base to an NMO mount. Also includes "O" ring-to-body, seal to prevent moisture oxidation.

NMO6 $8.95

NMO to SO239 Antenna Adapter
When you don't care to drill another hole for that whip, or new antenna, this heavy-duty adapter mates a SO-239 (PL259 type) antenna base to an NMO mount. Also includes "O" ring-to-body, seal to prevent moisture oxidation

.
$8.95 NMO8

Trunk Lip Mount (ABS) with steel lip clamp and dual set-screws. Accepts antennas with standard 3/8" X 24 thread base. Pre-wired with 17" of RG-58 to BNC Connector. Black rubber paint protector, see photo.

$7.97 TLMPL259

"The Adapter" is the best way to describe it ! Our number one seller when it comes to antenna adapters.

$ 2.99 each Order 7060

BNC male to UHF Female $2.99 ea

QUAD MAGNET, Antenna Mount.
Available in; Triple Chrome Plate, or Basic Black. You asked for strength in a super mobile antenna mount, and WE DELIVERED ! Features 4, five inch Heavy-Duty magnets, equally spaced on a Heavy Duty, 1/4" thick, hard-drawn metal frame. The BUX4MM is prewired with 3/8" X 24 threaded (standard) Mount, and PL259 connector. Accepts 3/8 X 24 antennas

$44.97 BUX4MMC "chrome"

$44.97 BUX4MMB "Black"

$9.95

AIK150

$9.95 AIK1OO

Dual Antenna Mount accepts 3/8"X24 thread antenna bases.				"Super" Magnet 95 lb. pull strength. This powerful 5 inch magnet comes with 17 feet RG 58 coax with PL-259 connector. It has the standard antenna 3/8" X 24 female threads. A strong magnet mount for HAM type mobile antennas. Prewired with 17" RG58 cable PL-259 connector
$11.95 Order DAM		DBLBRKT $14.95		5" version MA1035 $14.95 3 " version MA1034 $12.95

You've heard about it, and here it is; The GOLDEN Super "ROD" antenna Six section, telescoping "rod" antenna for hand-held transceivers VSWR: Less than, 1.5:1 Connector: BNC male

Length: 108cm extended (48") and 26.5cm collasped. approx.
~~$12.95~~

MARINE ANTENNA
No Ground VHF Marine Antenna.Ideal for bass boats, small run-about, and sail boats. 3 dB gain effectively doubles your transmitter's effective radiated power. Great for auto's with fiberglass body's or for wood craft - no ground required. Low profile 36" height is ideal for top mast mounts on sailboats or for use on bass and ski boats or run-a-bouts where long antennas might hamper operations. Comes complete with stainless steel "L" type mounting bracket and preassembled 15' coax cable fitted with PL259 connectors.

Our MoBALUN is also ideal for marine antenna installations.
When you hear those strong HF mobile signals, here's one reason they stand out from the rest. By installing the BUX MoBalun near the input to your antenna, you deliver more RF energy to the antenna. At the same time, the BUX MoBalun prevents RF from traveling back along the shield (high SWR) of your coax. High power rating, Low-permeability toroid, with Internal composition fiber-glass to prevent vibration during mobile operation. For input and output connectors, we use only the best Silver plated, Teflon insulated, SO239 connectors.

HR-22 $7.99

$37.97

19.95 MOBALUN

3 inch, NMO Magnetic antenna mount. Black finish, and a good "grabber" to a smooth, flat, metal surface. A good companion mount for the DB-2. Black finish, and a good "grabber" to a smooth, flat, metal surface. A good companion mount for the UV325 shown near top of this page.

5 inch, NMO Magnetic antenna mount. Black finish,
and a good "grabber" to a smooth, flat, metal surface. A good companion mount for the DB-2 shown on this page. This is a Larger, 5 inch heavy duty Magnet, w/coax and connector. 5 inch, NMO Magnetic antenna mount. Black finish, and a good "grabber" to a smooth, flat, metal surface. A good companion mount for the UV325 shown near top of this page.

DB-2

Dual Band mobile antenna for 144 & 430 MHz VSWR: Less than, 1.5:1 Connector: NMO base. Length: 39cm or 15.5 in. approx. ADD the NMO, 5 inch magnet mount for a durable, dual-band mobile antenna combo

AM-1043B 3.5 Inch, $14.95

AM-1045B 5 Inch $17.95

DB2 $14.95

Hi Quality Belden coax nine ft. jumper made using top quality Amphenol connectors.

$6.97 ORDER No. HIQ9JMPR

AM-101. Magnetic SO239 Mount 3.5" strong magnet mount with black plastic finish. 17' RG58 coax with PL-259.

12.99

Six (6) ft RG-8U, High Quality, 50 Ohm impedance, Coax jumper.

These jumpers are made from high quality, lowloss, coax cable with PL259 connectors installed at each end.

Ideal for transceiver to amplifier, Amplifier to antenna tuner and similar applications.

$ 6.95 each, Order code 8U6PLPL

F=1-5/8"

T=1"

S=1-1/8"

C=1/4"

W=5/32"

Eyebolt with nut, Machine Thread Zinc Plated.

5/32" X 1-5/8" EYE = 1/4"

HUNDREDS OF USES !
BALUN hang'n-hook, mobile antenna tye-downs, rope guide on tower, or pull-up masts, and much more.

Order EYEBOLT
39 cents each

Order EYEBOLTX3
3 for 99 cents

Both, DB-2 and 1045B for only: $29.95

Great for Apartment Dwellers, RV, pickup truck-bed rail, or Bumper installations. Rail or Bumper Heavy-Duty Antenna Mount

Length of this bar is 12 inches, and width is 2 inches. The bar is almost one quarter inch thick. Mounting screws and 3/8" X 24 standard thread, stud mount are included. By using our KD-3 Kwik-Disconnect, you can quickly change bands, or make your antenna setup into a "stealth" installation

Shown here is our T-BAR TRUX Stake hole mount. This one is for the serious HAM. The T-Bar mount is constructed of stainless steel and locates the antenna directly over the truck bed rail. Expandable rubber base locks mount for secure fit when tightened. Great for our HF stix and out heavy-duty whips. Fits most pickup truck models and brands. Heavy Duty Right angle SO239 and 3/8" x 24 threaded stud, included,

$29.95 DB2-45

$14.95 order BUXTRUXHD

TSTAKMNT $22.95

Right Angle SM1L Mount Right angle stud mount with SO239 coaxial cable connector and a 3/8-24 threaded antenna socket. Great for those cramped areas. Reg ~~11.95~~, BUX COMM Price: $8.88	Pick-Up Truck, Flat-BAR, STAKE HOLE Mount with SM1 for 3/8" x 24 thread base antennas.	Adjustable Bumper Mount with 3/8"x24 thread SM-1, and SO239 (PL259) input. Both may be used on hatch-back lid-lip, trunk-lip, bumper & hood.
$ 6.95 each	$19.95	442 S $16.95
BUMPER MOUNT with SO239 input connector, accepts PL259. $9.95 Order 422-S
422S $9.95	Ball Mount with SO-239 (female) connector, AM601S $11.95	Ball Mount with terminal lug connection, AM601L $11.95

Heavy Duty Spring for Whips up to 102 inches.	Often called the mobile antenna, Kwik-Disconnect This Mobile Antenna Adapter... is a 'SNAP' to change antennas or bands in a matter of seconds	Set of five (5) Kwik-Connect Antenna adapters and snap-on stud. Make changing mobile antennas a 'SNAP!' with a set of 5 ''Kwik Disconnect'' adapters.
S55S $8.95	KD3 $5.95	KD5 $15.95 Set of 5.

The EZ230 enables you to fold your mobile antenna over to a low-profile, horizontal position.

This prone position allows entry into low-overhead garages, and prevents damage to the antenna. A "must" for the mobile HAM.

Both sleeve and threaded section are standard
3/8" X 24 threads.

Dual Band whip antenna for 144 & 440 MHz VSWR: Less than, 1.5:1 Connector: 3/8" x 24 threads dual-band mobile antenna.
As shown, antenna only, requires 3/8 X 24 base.

Lost the ferrule that holds your whip-tip atop your BUX-STIX antenna? Here is the replacement complete with set-screw. Threads are standard 3/8 x 24.

EZ230 $9.95

14440WP $3.97

TIPFERL $3.97

50 Ohm impedance, 3 ft, 6 ft, 9 ft, 12 ft, & 18 feet.
These jumpers are made from high quality, low-loss, Belden coax cable with Amphenol PL-259 connectors installed.
Three ft. (3')    ORDER No.      8X3PLPL $3.99
Six ft. (6')         ORDER No.      8X6PLPL $4.99
Nine ft. (9')      ORDER No.      8X9PLPL $5.99
Twelve ft. (12')   ORDER No. 8X12PLPL $7.99
Eighteen ft. (18')ORDER No. 8X18PLPL $8.99

Fifty ft. (50') RG8X with PL259 installed on each end ORDER No. RG8X50PLPL $24.95
One Hundred ft. RG8X with PL259 installed on each end ORDER No. RG8X100PLPL $37.95

Shop Online or call our Order Line Monday thru Friday (except holidays) 1-434-534-8873
Customer Service [email protected]
Download our Catalog As of December 10th our brand new Winter 04/05 catalog is available in PDF FORMAT

Bumper Mount includes (SM1) SO-239 UHF connector to 3/8x24 antenna base (see SM1, this page). $7.95 ea

Included→ AM370RS

Insulated Antenna Stud Mount with SO-239 female connector for easy connecting with
PL-259 fitting. Threaded for standard 3/8 X 24 mobile antenna use.

$ 2.99 SM1

10 for 17.95

Mirror-Mount with insulated stud, for 3/8 X 24 thread medium duty mobile antenna mounting.

AM304S

$6.95 Each

Replacement, Hardened, Nylon, Heavy duty, Shoulder washer insulators, same as shoulder washers in SM1 Stud-Mount.

4 for 99¢ SM1SW

DVM 810
PocketCraft 810B. Here's a digital multimeter (DVM). Ideal for the Mountain-topper HAM Radio Operator, or technician. It has an LCD 3.5 digit readout
Features found on more expensive meters are standard on this DMM, they include:
* A transistor and diode tester
* DC Amperes

* AC Amperes
* Overload protection
* 7 functions & 19 Ranges
* Includes 21" test leads and battery.
Ranges to: 1000 Volts DC, 750 Volts AC, 10 Amps DC, Resistance to 2,000,000 Ohms

Order DVM810

$ 9.95

All text and graphics on these pages are ©®™ of G. E. Rogers Sr and BUX COMM Corp 1986 - 2006

For Quantity Quotes or Dealer Pricing;

* "RASCAL" is Registered trademark ®™ of BUX Communications Corp (BUX CommCo ™) *(RASCAL™® "Radio And Sound Card Adapter Link")

HandHeld "HR-9" Duckie Frequency: 144 - 148 MHz

HandHeld "HR-9" Duckie

Frequency: 144 - 148 MHz