Tell your friends, you found it at:

 Serving Telecommunications and HAM Radio since 1969
Monday thru Friday 9am to 4pm Eastern, Call Toll-free, 1 866 300 1969   &  1 800 726 2919 Orders Only!

  We accept:  

BASE STATION ANTENNAS  and ACCESSORIES
 NOTICE: We ship WINDOM and G5RV antennas worldwide, However; Due to excessive damage, we cannot ship HF Mobile or VHF Base antennas outside the continental USA !

THIS MONTHS "RED-HOT"  SPECIAL
2 meter version:  144 to 148 mHz
REGULAR    $39.95  SALE price 27.95 
JPOL2   
70cm version:   430-450 mHz
REGULAR    $34.95 SALE price 24.95 
JPOL4 
BUY BOTH for $49.95  Cat# JPOL270

Rugged Construction designed to last for years, these J-POL's are built by BUXCOMM corp in the USA. They are complete, with all mounting hardware, U-bolts, connectors, and photo instructions.

Add the BUX Decoupling "UNUN" for added isolation between the coax and J-POL for maximum transfer of RF energy to the antenna
and minimum (cable-loss) VSWR.
  $19.95  CAT#   BUXUNUN   
↓ This 160 thru 6 meter WINDOM is completely assembled ↓

 In Stock   BUX Model 166260 includes three (3) insulators, PVC covered, Power-Flex,  tinned, copper wire, connectors, and "BUX Black Hawk BALUN".  This 160 thru 6 meter WINDOM is completely assembled, ready to connect your coax, and erect.    You can be on the air in no time, with our model 166260,  $79.95                
 $79.95  With 4:1 BALUN↑WINDOM ↑ "without coax" Model 166260 
 $89.95  With 6:1 BALUN ↑WINDOM ↑ "without coax" Model 166261 

166260 With 4:1 BALUN with One Hundred ft. (100') RG8X coax and connectors, $ 129.95 166260W100 
166261w100 With 6:1 BALUN with One Hundred ft. (100') RG8X coax and connectors, $ 139.95 166261W100 
 

In Stock   80 thru 6 meter WINDOM  completely assembled↓

Similar to WINDOMs shown above, except is 136 ft overall.  This WINDOM is completely assembled, ready to connect your coax, and erect.   BUX Model 806136 is SSB power rated at 1000 watts and includes three (3) insulators, PVC covered, Power-Flex,  tinned, copper wire, connectors, and BALUN.   See coaxial cable and related items below.  You can be on the air in no time, with our model 806136. 
  $59.95  with 4:1 BALUN↑WINDOM ↑ "without coax" $59.95 Model 806136 
$69.95  with 6:1 BALUN ↑WINDOM ↑ "without coax" $69.95 Model 806137 

Above Windom (with 4:1 BALUN), with Fifty ft. (50')  RG8X coax, $ 79.95  806136W50  
Above Windom (with 6:1 BALUN), with Fifty ft. (50')  RG8X coax, $ 89.95  806137W50  
|Above Windom (with 4:1 BALUN), with One Hundred ft. (100') RG8X coax, $ 95.95  806136W100
Above Windom (with 6:1 BALUN), with One Hundred ft. (100') RG8X coax, $ 105.95  806137W100

In Stock   40 thru 6 meter WINDOM completely assembled

Similar to WINDOMs shown above, except is 70 ft overall and operates 40 thru 6 meters.  Completly assembled with BALUN, center insulator with eye-bolt (as shown), end insulators, and end ty-tails, attached. 

Without coax feedline     with 4:1 BALUN .       order number “40670”  For $49.95        
Without coax feedline     with 6:1 BALUN        order number “40671”  For $59.95        

 

With 50 ft of RG8X coax with 4:1 BALUN  order number 40670X50 for $ 68.95     
With 50 ft of RG8X coax with 6:1 BALUN  order number 40671X50 for $ 78.95     

 

With 100 ft of RG8X coax  with 4:1 BALUN order number 40670X100 for $ 87.95  
With 100 ft of RG8X coax  with 6:1 BALUN  order number 40671X100 for $ 97.95  

The illustration shown here is for use with the BUX COMM WINDOM models. 
This configuration may not perform with other antenna types.

With one of our BUX WINDOM antenna installations, we have about 24 feet at each end hanging down as shown, and we've noticed improved signals from stations using "vertical" antennas.
BUXCOMM ALL BAND DIPOLE

Order 80 thru 10 meter All Band Dipole, $ 39.95 Model 8010ABD  
All Band Dipole, 50 feet RG8X with connectors installed $ 58.95 Order Model 8010ABD50  
All Band Dipole, 100 feet RG8X with connectors installed $ 77.95 Order Model 8010ABD100  


The BUXCOMM model 1606G5RV Antenna
is complete, and includes:

• 205 feet of number 14 (awg) composed of 41 strands of silver plated copper wire,
• Sixty three feet of UV resistant coated, copper-clad Ladder-Line
• BUX “CARDINAL” BALUN.
• End (strain type) Heavy-Duty ceramic “egg” Insulators
• Center Support Insulator
• All connections are silver-soldered and coated with water-resistant compound and covered with 3M Weather-tite, shrink.

The overall length of the BUXCOMM model 160605G5 antenna is 205 feet.   The 160605G5 operates160 through 6 meters (also covers 30, 24, 17and 12 meters), is The UV resistant ladder-line is 63 feet, and the lower end terminates into our 1 kW, BUX "CARDINAL" BALUN.    The complete 160 thru 10 meter, BUXCOMM model 1606G5RV antenna SSB power rated @ 1000 watts.    For best installation and performance, use "Coax-Seal"   shown below.

Complete and Assembled for only $59.95.    Order Model 1606G5RV

BUXCOMM  model  G5RVPNP  80 through 10 meters
 Similar to 1606G5RV shown above, except it operates 80 through 10 meters;  102 ft overall.
ALL for only $39.95. Order Model G5RVPNP

G5RV  with seventy feet (70') of RG8X coax, $ 66.95 G5RVB70

USER INFORMATION:  The antenna ends should be secured with nylon rope or suitable supports.  The ladder line should have a near vertical (or slanted) drop from the center insulator for at least 25 feet and kept away from conductive objects. If the ladder line is installed near metallic or conductive objects, support the ladder-line as far from these objects as possible.  PolyVinyl conduit (PVC) stand-off supports at least 12 inches long can be employed to prevent contact with conductive objects, and tree limbs. UV resistant ties should be used to secure the ladder-line to insulated supports.

LOW-COST SOLDERING STATION 50W 350-900°F

Features :
manual temperature setting
electronic temperature control
power-on LED indication
with ground output

Specifications :
heater power for soldering iron: 50W
temperature variable control: 375-900°F
voltage supply: 115VAC
weight: 2.65 lbs.
dimensions: 7 1/4" x 3 31/32" x 3 1/2"
input power: 50VA max.

$ 24.90  Order VTSS5 ADD TO CART                                                           SPARE TIPS SHOWN BELOW ↓
Spare soldering tip for above High Q soldering station. CAT# BITIP5  $ 1.89  ADD TO CART

Great for electrical insulation, these 4" heat-shrink tubes come in three colors for easy identification of your wires.   Nine, 4 inch pieces, in three colors, and sizes.   Heat shrink tubing is a great way to manage wires in your Radio, transceiver, PC, auto, and much more.  The ideal solution for many of your wire protection needs.  This tubing has been specially formulated to shrink up to one half its original diameter simply by using a heat gun, soldering iron, or cigarette lighter.  Ideal for insulating electrical splices, and covering electrical plug-pins, solder joints, and connectors.   Cat#   9HST,   $ 1.44 pack
Each pack contains: Nine pieces,  in 4 inch lengths, Three colors, Three sizes--3/16" = WHITE,   1/4" = RED   and 3/8". = BLACK.        

For all type of outdoor antenna connections, BALUNS, Coax connectors, coax bulkhead entry panels and more. Use Coax-Seal® to protect any outdoor connection or connector. Coax-Seal is made of a non-conductive, non-contaminating waterproof material that remains flexible at any temperature from -30° to 180°F. Coax connectors that are not waterproof or have exposed solder joints can weaken from oxidation !

Coax-Seal is superior to electrical tape or vinyl sealants for moisture protection.

Each box of Coax-Seal contains (60 inches x 1/2 inch) five feet and will protect ten (10) connectors.

2.95 Order Code CS104

$2.95 Order Code CS104



 

BUX COMM LOOP ANTENNA

In Stock  $99.95 Order ↑BUXLOOP ↑"without coax" SEE COAX OPTIONS BELOW.
BlackHawk MM41 Included.

The "LOOP Sky-Wire" is completely assembled, with all wire, "float" insulators, "center fixed" insulators, BALUN (UnUn), ready to hang and attach your coax. 

*  LOOP Antennas have less electrostatic noise in your receiver.
*  LOOP Antennas provide additional gain over conventional wire type antennas
*  LOOP Antennas perform especially well over poor conducting earth like sand and lossy soils.

Many HAMs will tell you about a great antenna that was designed by Dave Fischer W0MHS.  For now though, let's say that the best overall performing wire antenna is one of the best kept secrets in HAM Radio.  I first learned about it in 1985 when Dave W0MHS wrote an article in the November issue of QST.  Dave called his design, "the   ''Loop Skywire.''  Today, we call it, the Full Wave LOOP Antenna.
 

There are several factors to consider when choosing your wire gauge and type. BUX COMM uses number 14 AWG, silver-flashed-copper, made up of 41 strands, covered with Flexible PVC. The (41) multi-strands provide an added (tensile) strength.   Because the wire size, most often referenced by HAM radio articles, is: #14 AWG, we have chosen it as the preferred size for our Full Wave, 80 thru 10 meters, LOOP antenna wire size.   In the construction of our antennas here at BUX COMM, we use a special, high grade wire, with 41 strands of silver flashed, copper with an U/V resistant PVC covering.  The covering will not affect the RF transmission in any way.   The formula we use to calculate the length of the Full Wave Loop Antenna is; L = 1005/f   "F" being the frequency of the lowest band to be used.   This formula is as accurate as you will need or want for the "loop antenna" on the HF bands. 
 

HF loop antennas can be constructed to be supported in one of two ways, "fixed and floating."  We use both methods of support.  For insulators to the right, left and diagonal of/to the feed point, we "float" the support insulator(s). 
 

When using one of the corners as the feed point, we employ a "fixed" insulator with a center hanger eye.  Diagonal to the feed-point and at the two non-fed corners, we employ "floating" insulators. This enables the wire to move freely, thus providing the best support when the horizontal loop is supported by tall poles or swaying trees.

The BUX COMM 80 thru 10 meter Full Wave LOOP Antenna is complete, including: all insulators installed, the BALUN (UnUn) installed, and all connections silver-soldered and weather-proofed.  All that is left is hanging it and connecting the coax feedline to the BALUN/UnUn.   See the *50 and **100 ft coax options for the Full wave LOOP antenna below.

 In Stock  $99.95 Order ↑BUXLOOP ↑ "without coax"  

Full Wave Loop Antenna Coax options
 *Above FullWave LOOP complete, with Fifty ft. RG8X coax with gold PL259s attached                119.95  BUXLOOP50  
**Above FullWave LOOP complete, with One Hundred ft. RG8X coax with gold PL259s attached  139.95 BUXLOOP100

 

ANT202 is a Base Station, antenna for (HF) 20, 17, 15, 12, and 10 meters.  We've also used it on 2 meters and 220 MHz with amazing success.
INCLUDES 2
end insulators.
 

 

A202 $27.95
←
For improved HF performance, we recommend our 101 BALUN (reg $ 19.95)
A202 & BALUN B101
SAVE $8.00, Order AB102

Both for $ 39.95  AB102  

 

Thru-Glass Scanner antenna. 

 

Covers 20 MHz to 1200 MHz. 

 

Supplied with 14 ft of coax with connector and mounting materials.  Installation instructions and recommended mounting location.                                                                                    

9.95  Order SCANT

EGG "strain" type ceramic, 1-3/8" insulator. Used as antenna end insulators, and for breaking up resonant or "Hot-Tower" guy wires.

3 for 1.99   Order 3EGG
 

450 Ohm ladder line comprises poly-coated open wire. It is much easier to handle than open wire feeder yet retains its ultra low loss feature.  This feed-line will handle 1 kilowatt with ease and is far superior to the 300 Ohm ribbon type.
 100 feet   $ 19.95 Cat #  450LADR  

50 feet  $ 11.95   Cat #  450LADR50

The cable shown here is 8 conductor Rotor Cable stranded with UV resistant PVC insulating jacket.

Wires 1 & 2 are Number 16, stranded, and tinned copper.

Wires 3 thru 8 are number 20, stranded, and tinned copper.

50 ft, $19.50   ROTR50        100 ft, $37.50,  ROTR100  


200 ft, $75.00 ROTR200      300 ft,  $111.95  ROTR300

Dipole and inverted-Vee antennas are commonly "balanced" at the feed points.  Coaxial feed lines are "unbalanced" by design personality (thus the name BALUN).  This BALANCED, to UNBALANCE marriage can only be performed by using a BALUN.  A BALUN should always be used when feeding wire antennas with coax to make certain characteristic antenna performance and optimum transfer of RF energy to the antenna complete.

When coax is used to feed antennas without the benefit of a BALUN, current flows on the shield of the coaxial feed line .  This coaxial shield current can produce  a "Hot HAM shack,"  This can result in nasty R.F. injury from the microphone to lips, hand key to fingers, etc., and is often more pronounced at certain frequencies.  Coax cable shield currents can also cause damage to your HAM gear.   TVI, RFI, telephone and even wild VSWR indications can result from these shield currents.  

In 85% of antenna projects that displayed these problems, when a BALUN is added to the coaxial line or near the antenna feed point, these problems were diminished or completely eliminated.

New dipole antenna center insulator for antenna builders.

  The SOCI has an SO239 coaxial connector and measures 2.5 inches long and 2.5 inches deep.

  • Build  your favorite Windom, G5RV, dipole, or inverted Vee

  • Very easy to install

  • Weather resistant

  • SO239 input connector

  • Use for Amateur Radio or SWL mono-band antennas

$  5.95    Order Code    SOCI  

 

 

 

Read why: BUX BALUN is

The # 1 selling BALUN

 

At BUX COMM, *We don't cut corners!


The elements used in the development of our BUX BALUNs are manufactured from top quality components, beginning with the Silver Plate SO239 connectors and center insulator, made of teflon™(E.I Dupont).

 

The wire we use to wind the ferrite donuts is heavy-duty, silver flashed wire, with teflon™ insulation that will handle RF voltages above 5000 volts, and extreme temperatures. The binding posts are heavy-duty, tempered brass, with end holes and side-thru holes to accommodate either type loop-thru connection.  A double-shoulder brass capture nut is used to add a secure bite and improve antenna wire electrical connections. 

BUX BALUNS are analyzed and tested in our lab, using a General Radio Impedance Bridge (GR1145) and Rhode & Schwarz, Vector Signal Generator and RF Spectrum Analyzer,  (SAM300) from 9 kHz -3 GHz to a WALFEUR 3000 watt, step range Pyronol-Dummy Load (SRDL3K).

With our BUX UN UN (ONION), the coax is Belden™ RG8X and the PL259 connectors are Amphenol™ with Silver flashed SO239, and Gold center pins.  Center Insulator is Teflon™ (EI DuPont)

From the BUXCOMM
Master-Match™ series
BUX ONION  $19.95

CAT#   BUXUNUN  
 

o 50 ohm, SO-239 unbalanced input
o UNBalanced output
o Two feet, RG8X to PL259
o 1.5 to 55 MHz  (160 Mtrs to 6 Mtrs)
o Toroid (CURRENT) design
o Heavy Duty, Lightweight
o Sealed against moisture
 

$19.95   ADD TO CART

NOTE:  BUXcomm BALUNs are equipped with stainless eyebolts for easy hanging support, and suspension.

MasterMatch™ 4:1
 BLACK HAWK

$19.95    MM41  

Our BUX Master-Match™ 4:1 current Balun is ideal for matching windoms, web'd or folded dipoles, and antennas fed at a 250 ohm to 500 ohm impedance feed point with normal 50 or 75 ohm coax cable. In contrast to ordinary Baluns the BUX MasterMatch™ 4:1 Balun support balanced currents in each leg of the antenna and prevents feedline (re)-radiation. As mentioned in our windom articles, feedlines and 450-ohm, brown, UV resistant, PolyCovered-Ladder-Line are easy to handle, and more-over they present another efficient means to feed multi-band antennas.  We strongly suggest the use of our UV resistant PolyCoat-Ladder-Line as it is made of strong, copper-clad, steel conductors. This light but durable, UV resistant Ladder-Line will  outlast the normal open copper with plastic spacers. (Includes three FREE antenna insulators, shown elsewhere, this page).

Master-Match™ "Black Hawk"  4:1 Features:
o DynaMAX Colored and Hardened, UV Resistant Resin Enclosure
o Toroid CURRENT design, wound with teflon covered, silver flashed, copper wire.
o 50 ohm, silver plated, gold pin, teflon center insulator, SO-239 unbalanced input
o Heavy duty Hardened Brass, Balanced output terminals.
o 160 Meters through 10 Meters
o Heavy Duty, Lightweight construction
o Sealed against moisture
o Equipped with stainless eyebolt for easy support, and suspension.
At BUX COMM, *We don't cut corners! The components used in the manufacture of our BALUNs are from top quality components, beginning with the UV resistant enclosures, then the Silver Plated SO239 connectors with center insulator made of teflon™(E.I Dupont). The wire we wind the ferrite donut with, is heavy-duty, silver flashed wire, with teflon™ insulation, which will handle RF voltages above 2500 volts, and temperatures above 400 degrees. The binding posts are heavy-duty, tempered brass, with end holes and side-thru holes to accommodate either type loop-thru connection. A double-shoulder brass capture nut is used to add a secure bite and improve electrical connections to the wire .
SPECIAL   BONUS !
Buy either our Master-Match™ 4:1 BALUN or our Master-Match™ 1:1   BALUN and receive "FREE," a Package of three TyNITE™ Insulators, shown elsewhere on this page.   The BUX Master-Match™ 4:1 & Master-Match™ 1.1 High Performance ,  1.5  KW Balun (if SWR is less than 2:1)  *CW/SSB duty-cycles only.   SSB/CW Power @ 3.5 MHz* >1.5 kW if SWR is less than 3:1  *Not rated for AM, RTTY or other high duty-cycle digital modes.

MasterMatch™ 1:1
 CARDINAL

  $19.95   Order MM11  

BUX Master-Match™ 1:1 current Balun is ideal for Dipoles, Slopers, Inverted-Vees and center feed-point, RV antennas. They are also employed at the driven element of of many HF beams and Quads, and where feedpoint impedance is at, or near 50 ohms. By equalizing the currents in the antenna feeders, the Dipole pattern improves and prevents feedline (re)-radiation by preventing antenna currents flowing along the outer braid of the coax or transmission Line.
Master-Match™ 1:1 Features:
o DynaMAX Colored and Hardened, UV Resistant Resin Enclosure
o 50 ohm, silver plated, gold pin, teflon center insulator, SO-239 unbalanced input
o Heavy duty Hardened Brass, Balanced output terminals.
o 1.8 to 54 MHz
o Toroid CURRENT design.
o Heavy Duty, Lightweight construction
o Sealed against moisture
o Equipped with stainless eyebolt for easy support, and suspension.
At BUX COMM, *We don't cut corners! The components used in the manufacture of our MasterMatch™ BALUNs are from top quality components, beginning with the UV resistant enclosures, then the Silver Plated SO239 connectors with center insulator made of teflon™(E.I Dupont). The wire we wind the ferrite donut with, is heavy-duty, silver flashed wire, with teflon™ insulation, which will handle RF voltages above 2500 volts, and temperatures above 400 degrees. The binding posts are heavy-duty, tempered brass, with end holes and side-thru holes to accommodate either type loop-thru connection. A double-shoulder brass capture nut is used to add a secure bite and improve electrical connections to the wire
SPECIAL  BONUS
Buy either our Master-Match™ 4:1 BALUN or our Master-Match™ 1:1   BALUN and receive "FREE," a Package of three TyNITE™ Insulators, as shown elsewhere on this page3 The BUX Master-Match™ 4:1 & Master-Match™ 1.1 High Performance ,  1.5  KW Balun (if SWR is less than 2:1)  *CW/SSB duty-cycles only.   SSB/CW Power @ 3.5 MHz* >1.5 kW if SWR is less than 3:1  *Not rated for AM, RTTY or other high duty-cycle digital modes.

AMERICAN EAGLE

2500 WATT BALUN
This is our BUX COMM High-Performance, Heavy Duty, "Big Talker"
We designed it to cope with a "couple" kilowatts... or  three.   We decided that was NOT good enough, so we built it to endure harsh treatment.

  STATS: Current Balun, Wt. 1.5 LBs, 4:1 Hi-Power, 160 thru 10 Meterz
  HEAVY DUTY TOROID MADE OF TYPE 43 FERRITE
  LOW PERMEABILITY CORE
  2500 WATT 4:1 current High Performance, Heavy Duty,
  *CW/SSB duty-cycles only.  SSB/CW Power @ 3.5 MHz* >2.5kW * SWR  is less than 3:1, Not rated for RTTY & AM
 Will not saturate at Amateur Radio Power Levels  Regular $64.97   
 Equipped with stainless eyebolt for easy support, and suspension.

Order Model AE41 $ 34.95  

1:1 version High Performance, Heavy Duty, 2500 WATT (Current BALUN),
Order Model AE11  $ 34.95

FALCON 6:1 balun

50 ohms unbalanced (coaxial) to 300 ohms balanced
For use with OCF dipoles, doublets, and antennas fed with 300 ohm transition sections 1 .8 MHz to 55 MHz @ 1Kw

o 50 ohm, silver plated, gold pin, teflon center insulator, SO-239 unbalanced input

o Heavy duty Hardened Brass, Balanced output terminals.

o 1.8 to 55 MHz

o QUAD Toroid design

o High Efficiency

o Lightweight construction

o Sealed against moisture

o BUXcomm BALUNs are equipped with stainless eyebolts for easy hanging support, and suspension.
 Order Model  FALCON  $ 29.95

PeWe41  4:1 BALUN
From the BUXCOMM  Master-Match™ series

The BUX PeWe41 is a member of our Master-Match™ series. PeWe41 is a 4:1 High Efficiency Current BALUN and is conservatively rated for QRP to 550 watts when operated with an VSWR better than 2:1 CW/SSB duty-cycles; 

SSB/CW Power @ 3.5 MHz* >550 watts when SWR is less than 2:1.  200 watts *AM, RTTY or high duty-cycle digital modes when VSWR is less than 2:1.  

1.8 to 35 mHz

o Toroid CURRENT design, wound with teflon covered, silver flashed, copper wire.
o 50 ohm,  SO-239 unbalanced input
o Heavy duty Hardened Brass, Balanced output terminals.
o 160 Meters through 10 Meters
o Heavy Duty, Lightweight construction
o Sealed against moisture
o Proudly Made in the USA
o BUXcomm BALUNs are equipped with stainless eyebolts for easy hanging support, and suspension.

 Order Code:   $16.95 PeWe41  

From the BUXCOMM  Master-Match™ series
PeWe  1:1 BALUN

The BUX PeWe11 is a member of our Master-Match™ BALUN series.  It is a 1:1 High Efficiency Current BALUN and is conservatively rated for QRP to 250 watts when operated with an VSWR better than 2:1 CW/SSB duty-cycles; 

SSB/CW Power @ 3.5 MHz* >550 watts when SWR is less than 2:1.  150 watts *AM, RTTY or high duty-cycle digital modes when VSWR is less than 2:1.  

1.8 to 55 mHz

o Ferrite, Toroid CURRENT design.
o 50 ohm,  SO-239 unbalanced input
o Heavy duty Hardened Brass, Balanced output terminals.
o 160 Meters through 6 Meters
o Heavy Duty, Lightweight construction
o Sealed against moisture
o Proudly Made in the USA
o BUXcomm BALUNs are equipped with stainless eyebolts for easy hanging support, and suspension.

  Order Code:   $16.95 PeWe11  

ebux
 

MOBILE KING, Antenna UNUN
For bottom fed, and Screw-Driver antennas.
1.8 MHz to 54 MHz
 Master Match
MOBILE KING "Big Talker"  UNUN
 

o  FREE  3ft RG8X coax jumper with PL259's.
o 1.8 to 54 MHz
 o Ferrite (current) Broadband Toroid design
 o Heavy Duty, Lightweight construction
o SO-239 UNbalanced input.
o SO-239 UNbalanced output,
 o Sealed against moisture

 In Stock  Order SDAB  UNUN  $19.95

BUX VBALUN De-Coupling transformer

Primary use and application:
Feed point isolation and matching for J-Poles and VHF/UHF BEAMS.

This decoupling transformer prevents RF currents from traveling down the outer shield of the coax. The input connector is an SO239 (female) and the output connector is a PL259 (male).

BUX "VBALUN" De-Coupling transformer, has SO-239 (female) input connector.  Output connector is 2 feet RG8X cable with Amphenol PL-259 (male).   BUX VBALUN is an UNbalanced to UNbalance decoupling transformer designed to be used by the Apartment dweller or the RV ops when feeding J-Poles and similar VHF/UHF antennas. 

$19.95  VBALUN

Teflon ®™ E I DuPont corp.
Amphenol ®™ TYCO Corp.

NOTE:  BUXcomm BALUNs
are equipped with stainless eyebolts
for easy hanging support, and suspension.

 
ebux


BUX COMM BALUNS are equipped with stainless eyebolt for easy support, and suspension.

For all type of outdoor antenna connections, BALUNS, Coax connectors, coax bulkhead entry panels and more. Use Coax-Seal® to protect any outdoor connection or connector. Coax-Seal is made of a non-conductive, non-contaminating waterproof material that remains flexible at any temperature from -30° to 180°F. Coax connectors that are not waterproof or have exposed solder joints can weaken from oxidation !

Coax-Seal is superior to electrical tape or vinyl sealants for moisture protection.

Each box of Coax-Seal contains (60 inches x 1/2 inch) five feet and will protect ten (10) connectors.

2.95 Order Code CS104

$2.95 Order Code CS104



 


A good method to suspend a balun and the center of your antenna without placing undue stress on the BALUN or the binding posts.

Stainless eyebolt is inserted into Tenyte "Center Insulator"  The "Center Insulator" is used to suspend the center of a Dipole,  Windom, or other wire type antenna from tower, tree, or support structure.

Center Insulator
with Suspension Eyebolt
 

      1.99  Order CIA   

Center Insulator and two end insulators  3.99
 Order CIAX3 

For the apartment dweller, you can now hang the 20 meter doublet in the attic.  I've QSO'd with stations all over the world with the 33 ft dipole in the attic of my garage.  One insulator at the center, and one each end.  It's great for other HF WINDOM and or dipole antenna.  Dielectric strength is better than the old ceramic insulators, but without susceptibility to cracking or breakage under impact or extreme temperature changes.

 

Package of  3,  $2.99   
 Antenna Insulators  

Package of 10,  Insulators $8.99, ANTINSLX10


EGG "strain" type ceramic,
1-3/8" insulator.  Used as antenna end insulators,
and breaking up resonant
or "Hot" guys.

3 for 1.99   Order 3EGG  ADD TO CART

 
MEDIUM EGG "strain" type ceramic, 2" insulator. Used as antenna center and end insulators, and for breaking up resonant or "Hot-Tower" guys
 3 for 2.99   Order Code LEGG ADD TO CART

LARGE 2-1/2 inch X 1-3/4" Very strong, High density Ceramic, Strain Type Insulators.  For antenna suspension and end insulators and when breaking up resonant guy wires, and tower support systems.   3 for 4.95  
CAT #  EGG25    ADD TO CART
Fifty ft. (50') RG8X with PL259 installed on each end            ORDER No. RG8X50PLPL  $24.95  

One Hundred ft. RG8X with PL259 installed on each end ORDER No. RG8X100PLPL $37.95  

Important Information;                                    WHY USE A  4:1 BALUN

Krusty Olde Kurt is now going to repeat himself.  Why? Because the same question keeps coming up over and over. And he wants everyone to get it right.   "I'm feeding my dipole with 600-ohm line.  At the station end I need a balun to convert to 50-ohm coax. I need a 12:1 balun, right?"   Wrong!  A 4:1 balun would be better.  Why is that?  If your dipole is up, let's say, 35 feet then on 80 meters it will probably have a resistance at resonance of about 40 ohms. The actual resistance depends on the height above ground in wavelengths. 

If the dipole is 40 Ohms then what do you see at the transmitter end of your 600 ohm line? If the line is a half-wave long (120 ft on 80 Meters) you'll see 40 ohms.   Remember, a half-wave line repeats what it sees at the other end.  But if it is a quarter-wave long you'll see 8500 Ohms!  At other line lengths you'll see impedances somewhere between these two extremes.   So you are not going to see 600 ohms at the end of your 600-ohm line. That only happens if you have a 600-ohm antenna hooked onto it. With such a variation in impedance at the trans­mitter end of the line there is no one balun transformer that will match it. Most of the time the impedance will be above the 50 Ohms of your coax so a high impedance balun would be desirable.  Unfortunately high imped­ance baluns don't work well when not matched.   

Experience has shown that 4:1 baluns work best in this service.  They are more rugged and will take bad mismatches especially if they are wound on an iron powder core.  So stop searching for that 12:1 balun. Use a 4:l BALUN and your system will work great.  

You can read Kurt N. Sterba “AERIALS” column in World Radio Magazine.

With an increase in local noise sources and the increasing attractiveness of long wire and dipole antennas, coax cable has become the antenna feed line of choice for most radio users and operators. 

 

Given that the impedance of most commonly available coax is either 50 or 72 ohms and since many wire antennas present an impedance of 200 to 600 ohms or more at the feed point, direct connection of the coax to wire antennas hits us with a significant signal loss due to the antenna impedance mismatch. 

 

Having realized this set of circumstances in the receiver and SWL arena, we're introducing a new approach to defeat the noise and impedance mismatch problems in our receive antennas by designing this new RxBALUN™.

 

Our RxBALUN™ bridges the impedance gap, and enables an unbalance to balanced match between the antenna and our receivers.  These features provide more signal transfer from the antenna to your receiver.  

 

Our RxBALUN will accommodate the SWL and QRP Operator.  In addition, this RxBALUN may be employed as an antenna balun for both transmit and receive between the antenna and low powered transceivers running up to 200 watts.  For input and output connectors, we use only the best Silver plated, Teflon®™ insulated, SO239 connectors. Max Power 250 watts.

$14.97 RxBALUN     Teflon ®™ E I DuPont corp.

Your BUX BALUN is warranted against defects in components or construction for a period of one year from date of purchase.  Our warranty does not cover damage due to misuse, abuse, or nonessential operation outside the  specifications of the BUX BALUN.  This warranty applies only to the original purchaser.  A copy of the receipt showing the purchaser’s name and the date of purchase must accompany BALUN's returned for warranty service.  All returns must be shipped prepaid.

Should there arise a requirement to return your BUX BALUN for service, carefully wrap and package it.   We will re-use your carton to return the BUX BALUN to you.  Be sure to include your return address.  Include a full description of the problem, along with your name, address, phone number and/or e-mail address.  Repairs average approximately 3 to 4 days.

SWL Antenna

This antenna may also be used as a 40, 20, and 10 meter Dipole for transmitting and receiving. MAX PWR 300 watts.
SWL, 68 ft, center-fed antenna complete with RxBalun and all insulators, end and center, coax feed is SO239. 29.95 + S&H
50 and 100 ft lengths of RG8X  with connectors, SO239 to match the above SWL antenna shown elsewhere on this page.

Order model  SWLANT  with BALUN  $ 29.95 
 
2 meter version:  144 to 148 mHz
(model JPOL2) 29.95  
 
 
70cm version:   430-450 mHz
(model JPOL4) 24.95

 

BUX VBALUN De-Coupling transformer

Primary use and application:
Feed point isolation and matching for J-Poles and VHF/UHF BEAMS.

This decoupling transformer prevents RF currents from traveling down the outer shield of the coax. The input connector is an SO239 (female) and the output connector is a PL259 (male).

BUX "VBALUN" De-Coupling transformer, has SO-239 (female) input connector.  Output connector is 2 feet RG8X cable with Amphenol PL-259 (male).   BUX VBALUN is an UNbalanced to UNbalance decoupling transformer designed to be used by the Apartment dweller or the RV ops when feeding J-Poles and similar VHF/UHF antennas. 

$19.95  VBALUN

Teflon ®™ E I DuPont corp.
 Amphenol ®™ TYCO Corp.

 

Hitch Pin Clips are used as "keepers" on many Cubicle Quad antenna spacers.  Keep a few "keeper" spares on-hand.  
Plated,  = zinc-coated.
Made of MB spring wire size=.042
Spring wire Diameter = 3/64
Max Shaft Diameter 5/16"
Overall length = 1 inch
Inside Diameter = 5/16 "

      10 for .99 cents  BUXCOMM Part No.  HPC223  

* 1/4 wave on 2 meters   * 2.5 dBi gain at  440 MHz.   * Rated at 200 Watts * 12 ft of RG-58 cable with *PL-259 connector.  
* Magnet mount designed for winds of 100 mph  * Overall height is 21 inches.

$17.95  VU1510

Same as shown at left, but has *BNC connector for use with hand-helds with BNC antenna input. $18.95 each ORDER
VU-1510-"B"

$18.95 VU1510B

5/8 wave antenna,
136 - 174 MHz
NMO Base
(Mount not included)
39 inches overall
VSWR less than 1.5:1
200 Watts

VH-1215 $16.95

5/8 wave antenna,
220-265 MHz
NMO Base
(Mount not included)

VSWR less than 1.5:1
200 Watts
220-265 MHz version  PM220    $21.95 

PM220  $21.95 











$VU-1545

17.95  

Recommended Mag Mount is AM-1045 B, NMO Mounts shown here.  Get both, the VU1545 VHF/UHF (NMO) Antenna & the AM-1045B, 5 inch, Super Heavy-Duty
Magnet Mount for $29.99
 

BOTH 1545 &1045 
for $29.95  

Need a High Quality jumper from your transceiver to the linear?  A HiQuality coax jumper for that transceiver Output to linear input! The connectors are Amphenol™ and coax is RG-8X by Belden.  Hi Quality, Six ft. (6') jumper made using high quality components

$6.97  HIQ9JMPR 


Remember the axiom; 'An ounce of prevention is worth a pound of cure.'  This lightning protector contains a modified spark gap that provides that ounce of prevention. . Remember, there is no substitute for a good earth ground, AC line surge, and spike protection. Where lightning is involved, we make no warranties. We offer the 7516 as a secondary lightning protector. Ground wire attached to wire lug.  $ 4.99 ea  Stock # 7516

STORM SEASON is just around the corner.  It pays to be prepared !
$ 4.99 ea 

Kit contains:
2 - Adhesive Pads
1 - Alcohol Surface Cleaning Swabs
1 - Trim Plate
1 - Shrink Tube
REMOUNT KIT  for all TG Series (Thru-Glass) Antennas.

REMNTKIT  5.97
BLACK CABLE TIES - 100pcs
.99 Pk of 100
Colour: BLACK (UV Resistant)
Dimensions (A x B): 98 x 2.5mm
Quantity: 100 pcs per/Pak
Material: polyamide (nylon 6.6) as specified in MIL-S-23190 self-extinguishing.
Temperature: -40°F to 230°F
Tensile strength = 18 pounds
A = 4 inches

.99 / Pak of 100
Order : KTFB3

140 - 170 MHz VHF
Economy Mag Mount Antenna.
 Order 2MMM  11.95

 
One and 1/2 inch (1-1/2")   Ubolt for use with most beam antennas and antenna support  masts.

This is the "standard" size clasp and U-bolt for use with masts up to 1-1/2 inch.

Complete with all parts, nuts, washers, saddle clasp, and flatbar.  See photo.

Order BUXUBOLT  3.49 each

 Order BUXUBOLT 

3.49 each

$ 6.95  each  


Dual Band Magnet Mount Antenna 14.95 Low-cost, high quality, dual band antenna with magnetic mount. Ideal for commercial two-way and HAM Radio VHF/UHF FM mobile applications. 200 watt rated.

DBMM  14.95

Use this mast-mounted bracket for 'fixed-station', field-day operating, apartment dwellers, or the mobile RV ops. 
With two of our mobile HF antennas  you can have the best of both worlds.  It is ou an ideal, single element, horizontal dipole (beam).  Shown mounted on 1 & 1/4" mast. Dual antenna bracket only, antenna(s) Not Included. 

See BUX HF STIX below 

DBLBRKT  $14.95
  

BLACK CABLE TIES - 100pcs
.99 Pk of 100
Colour: BLACK (UV Resistant)
Dimensions (A x B): 98 x 2.5mm
Quantity: 100 pcs per/Pak
Material: polyamide (nylon 6.6) as specified in MIL-S-23190 self-extinguishing.
Temperature: -40°F to 230°F
Tensile strength = 18 pounds
A = 4 inches

.99 / Pak of 100
Order : KTFB3

 


Great for HandHelds
and it is  ideal for use
as a rapid-deployment
antenna.

order VM101
$ 12.59

 

Number 14 TW/AWG with 41 strands of tinned copper wire, Poly-Vinyl insulation covered flexible, but strong.  The most preferred wire type when building Dipole's, Windom's, and other flat-top HF antennas.  The PVC insulation gives added strength to the 41 strands of tinned, copper wire.  Specification:  Finely stranded tinned copper conductor (Type III),  105ºC   600 volt copper. 1.5lb/100 Color coded PVC insulation, Temperature range  -20°C to 105ºC, Voltage rating 600 volts, Reistant to Acid, Alkilis, Abrasion, Flame, Gasoline, Oil, Ozone, Moisture, Fungus.  
100 ft, $19.95 10014 ;   200 ft, $38.95,  20014
300 ft, $57.95 30014 ;   400 ft,  $76.95  40014

For all type of outdoor antenna connections, BALUNS, Coax connectors, coax bulkhead entry panels and more. Use Coax-Seal® to protect any outdoor connection or connector. Coax-Seal is made of a non-conductive, non-contaminating waterproof material that remains flexible at any temperature from -30° to 180°F. Coax connectors that are not waterproof or have exposed solder joints can weaken from oxidation !

Coax-Seal is superior to electrical tape or vinyl sealants for moisture protection.

Each box of Coax-Seal contains (60 inches x 1/2 inch) five feet and will protect ten (10) connectors.

2.95 Order Code CS104

$2.95 Order Code CS104



 
RG8U
 100 feet of RG-8U Low-Loss, Base-Station Coaxial Cable.   It's low loss design and 97% or better shield makes it ideal for this application.   PL-259 coax connectors are installed on each end		 50 feet of RG-8U with 97% shielding, Low-Loss, Base-Station Coaxial Cable.
ORDER:  RG8PL1L
$39.97     Both ends are fitted with  plated PL259/7506 connectors !   
100 feet of RG-8U, with 97% shielding, Low-Loss Base-Station Coaxial Cable.
ORDER:  RG8PL1C
$59.97    
 RG213
Low-Loss, Base-Station Coaxial Cable.   Ultra low loss design with double shield makes it ideal for this application.  PL-259 coax connectors are installed on each end		 50 feet of RG-213 double shield, Ultra Low-Loss, Base-Station Coaxial Cable.  ORDER:  RG213PL50 $49.97    

Both ends are fitted withPL259/7506 connectors !    100 feet of RG-213, double shield, Ultra Low-Loss Base-Station Coaxial Cable.
ORDER:  RG213PL100 $69.97    


50 Ohm impedance, 3ft, 6ft, 9ft, 12ft,18ft, 50ft & 100 feet.
These jumpers are made from high quality, low-loss, Belden coax cable with Amphenol PL-259 connectors installed.
 Three ft. (3')    ORDER No.      8X3PLPL  $3.99    
Six ft. (6')         ORDER No.      8X6PLPL  $4.99     
Nine ft. (9')      ORDER No.      8X9PLPL  $5.99     
Twelve ft. (12')   ORDER No.  8X12PLPL  $7.99  
                                         Eighteen ft. (18')ORDER No.  8X18PLPL  $8.99  

Fifty ft. (50') RG8X with PL259 installed on each end            ORDER No. RG8X50PLPL  $24.95  
One Hundred ft. RG8X with PL259 installed on each end ORDER No. RG8X100PLPL $37.95  

BUX HF STIX  In Stock

BHF75M  75 METER  3/8" X 24 THREAD 8 feet long $16.95     

BHF40M 40 METER  3/8" X 24 THREAD  8 feet long $16.95       

BHF20M 20 METER 3/8" X 24 THREAD  8 feet long $16.95        

BHF17M 17 METER  3/8" X 24 THREAD 8 feet long $16.95        

BHF15M 15 METER 3/8" X 24 THREAD 8 feet long $16.95        

BHF10M 10 METER  3/8" X 24 THREAD 8 feet long $16.95        

BHF6M  6 METER  3/8" X 24 THREAD 5 feet long  $16.95          

These two-piece Mobile antennas consist of a hollow fiberglass base section approximately 1/2 inch diameter with the loading coil wound directly on the fiberglass and covered with shrink tubing.  The chrome plated brass base fitting has 3/8 inch X 24  threads that fit the amateur standard 3/8" X 24 mobile mount.
 

Replacement, 48 inch Tips for above tuneable-tip  antennas.    TIP48, $2.95      →       →      

BUX stix  HF antennas for Mobile and Base Applications:
 Power Rated at 250 Watts P E P;   Typical 2:1.VSWR band width is:

·        75 meter: 40 KHz.         40 Meter: 60 KHz.
·        20 Meter: 150 KHz.      17 Meter: 175 KHz.
·        15 Meter: 200 KHz.      12 Meter: 300 KHz.
·        10 Meter: 500 KHz.        6  Meter: 1000 Khz.

TUNING INSTRUCTIONS:
Insert the whip into lower section ferrule about four inches (as shown at right) and tighten set screw.   Assemble with fiberglass lower section (as shown at left). Install a VSWR meter at the transceiver and apply 10 to 25 watts of power. Adjust the VSWR meter and output frequency for lowest VSWR reading, indicating resonance.  If resonant frequency is too high, loosen set screw and extend top whip until desired resonant frequency is found.  If  resonant frequency is too low, loosen set screw and adjust whip further into lower section.  For best results, adjustments should be made in small increments. 

CAUTION:  If required, cut off the bottom of the whip to ensure it does not extend down into the coil of the antenna.  Failure to observe this precaution will cause heat damage and void any warranty.  At resonance, VSWR should be 1.5:1 or less when properly matched. When tuning is complete, tighten set screws securely.   NOTE: Bandwidth and VSWR will vary due to   mounting location.  If your installation has a VSWR over 1.5:1 at resonance, or you need to operate over a greater bandwidth a tuner may be required.

 

DBLSPCL (without BUX UNUN (ONION)

When the stations with the gain and power in their antennas are transmitting in the horizontal plane, then you should be meeting them in the same plane.  Horizontal signals tend to follow the earths contour, and are easier to capture using a horizontally polarized antenna.  See the BUX UNUN elsewhere on this page.

By combining a pair (two) of the single band HF Mobile (loaded) tuneable-tip antennas above, you can have an ideal, single element, horizontal dipole (beam). This type antenna opens the world of HF communications for the apartment dweller, RV HAM, field-day operating, and a variety of other uses and applications.  The packages described below include two antenna, the Double Antenna-Bracket (DBLBRKT), and mounting hardware.  $ 39.97 DBLSPCL (without BUX UNUN (ONION)
75 Meters→,  40 Meters→, 20 Meters→,

17 Meters→,  15 Meters→,  10 Meters→,

 

 6 Meters →         In Stock

BUX Double Combo "with" BUX ONION (UNUN).  
 By combining a pair (two) of the single band HF Mobile (loaded) tuneable-tip antennas above, you can have an ideal, single element, horizontal dipole (beam). This type antenna opens the world of HF communications for the apartment dweller, RV HAM, field-day operating, and a variety of other uses and applications.  The package described here include: two antenna, the Double-Bracket (DBLBRKT), mounting hardware, and BUX BALUN (UNUN).
$AVE,  BOTH, DPLSPCL & BUXUNUN, for only $ 54.97, ORDER, DBLCOMBO 
75 Meters→,   40 Meters→,   20 Meters→,

 17 Meters→,   15 Meters→,   10 Meters→

 

6  Meters →          In Stock

DUAL BAND, HIGH GAIN, BASE STATION ANTENNA, UVS-200
  6.7 db @ 2 meters, 8.2db 70cm. High Performance, High Gain, Dual Band, Base Station Antenna 5/8 wave, vertical stacked collinear design 2-5/8 elements on 2mt., 4-5/8 elements on 70cm.   6.7 db @ 2 meters and 8.2 db 70cm. Superior wideband performance Heavy duty fiberglass radome Durable, waterproof joints Mounting Hardware included Accepts standard PL-259 connector 200 Watt power rating Radiating element, 100 inches. DC ground, enclosed elements reduces terrestrial noise.


 

 

 

 

 Reg $109.95 BUX COMM price,  $57.97      

UVS-200         In Stock


Description:

 2M/70CM DUAL BAND FIBERGLASS VERTICAL GAIN GROUND PLANE ANTENNA

HIGH PERFORMANCE , HIGH POWER RATING, LOW SWR AND BROADER BAND COVERAGE ON BOTH 2m AND 70cm BAND.

SPECIALLY DESIGNED TO KEEP THE ANTENNA STRAIGHT AS ONE ELEMENT.

USING RING GASKET MAKES ANTENNA PERFECTLY WATERPROOF.

EASY ASSEMBLY JUST BY TIGHTENING THE JOINT ACCORDINGLY.

INSULATED CONDUCTOR, LESS INTERFERENCE FROM RAIN, SLEET AND SNOW. REDUCED PRECIPITATION STATIC, LOWER BACK GROUND NOISE.

DC GROUND DESIGN LEADS THE HIGH VOLTAGE CAUSED BY THUNDER AND LIGHTENING TO THE GROUND, PROTECTS RADIO EQUIPMENT.

ACCEPTABLE MAST DIAMETER 30-62m/m (1-3/16" 2-7/16")

SUPPLIED WITH MAST BRACKET, V-BOLT, SUPPORTT TUBE AND ALL MOUNTING HARDWARE.

ELECTRICAL SPECIFICATIONS: LENGTH 2.5m (98.4"), GAIN 2m 6dB/70cm 8dB, CONFIGURATION 2m 5/8 WAVE 2-ELEMENT/70cm 5/8 WAVE 4-ELEMENT, FREQUENCY 144~148/435~450 MHz, MAX POWER 200 WATTS, IMPEDANCE 50 OHM, V.S.W.R LESS THAN 1.5:1, CONNECTOR SO-239 (UHF).
 Reg $109.95 BUX COMM price,  $57.97      

UVS200         In Stock

VH2201 VHF BASE & REPEATER Antenna.
Frequency Range:
136-174 MHz
Gain: 4.5dB
VSWR less than 1.5:1
Power Rating: 200 watts
Impedance: 50 Ohms
Stainless Steel Radials
SO-239 Input connector
Radiating element Length 6 feet.
Built to Commercial standards for base station installations,
and  rugged, mountain-top repeater applications.  Mounting
hardware and stainless-steel radials included.  Ship wt, 5 Lb

$47.97  VH2201             In Stock

UH2401 UHF BASE & REPEATER Antenna
Antenna Frequency Range: 430-490 MHz
Gain: 6.5dB
Power Rating: 200 watts
Impedance: 50 Ohms
Stainless Steel Radials
SO-239 Input connector
Radiating element
length 5 feet.   Built to Commercial standards for base station installations, and rugged, mountain-top repeater applications. Mounting hardware and stainless-steel radials included. Ship wt, 5 Lb

 

 $47.97 UH2401         In Stock

"Vertical" Six Meter Ground Plane


All mounting hardware and assembly instructions are included.

Also includes cutting chart for exact frequency measurements.


Solid Hard-Drawn Aluminum GP6M $49.95  In Stock

 

VHF and UHF 'Cross-Needle' High
Performance, SWR & POWER Meter.
For the serious VHF/UHF operator, here is a 140 to 160 MHz & 440 to 480 MHz, VSWR and POWER meter with; 10 - 100 - 1000 watt scales.

 

 

 

 

SWR-6  $69.95           In Stock

SWR & WATT METER 100 watt & 10 watt level switch This is a handy, compact meter designed for the amateur radio operator. Test antenna performance and transmitter operation, 1.7 to 50 MHz. May also be used as a RF field strength meter and to check QRP.


SWR-3,  $19.95             In Stock

The perfect QRP SWR and Watt Meter.

SWR: 1:1 to 1:3;      RF Power: 0.5~10W;     Accuracy: =SWR: +- 5%
Power: +- 10%;        Impedance: 52 W,         Meter Sens. 200uA
                                    Freq. Range 1.7 to 30MHz


QRP, SWR & POWER Meter, (0.5 to 10 watts) with SO 239 connectors.
 

SWR-2T,  $12.99            In Stock

The Duplexer shown here is the ideal companion for our Dual-Band, Base Antennas  !  HF and VHF/UHF Antenna Duplexer  (Indoor use)


Frequency: (Port 1) 1.3 - 225 MHz,  (Port 2) 350 - 540 MHz
Power:       500 W 1.3 - 35 MHz,    300 W 50 - 540 MHz
Insertion Loss: <0.2 dB Isolation: 60 dB;    VSWR: < 1.2:1
Combine HF/6m/2m output (Port 1) and your UHF output
from your transceiver and send to one antenna.

In Stock

$34.95  Order DU-500    

 

Specifications:

 

Frequency Range:  Up to, and including 600 MHz
VSWR:  Below 1.2:1
Power Rating:  1.5 kW peak 1kW continuous
Impedance:  50  Ohms
Insertion loss:  Less than 0.2 dB.
Port Isolation:  Better than 50 dB.
Port connectors:  SO-239

One IN, Two Out, and
May be configured Two IN, One Out.

 2 Position Coax Switch

In Stock

CX-201  $19.95  

Antenna Coax Switch; 1  IN, 3 Out, in Metal case.
 Antenna Coax Switch; One IN, Three Out, or Three IN, and One OUT, 50 Ohm impedance, 3 port to 1 port Antenna Switch. Rated at 1 KW, SO-239 ports, mounted in metal case.

 

In Stock

 

CX3 $9.95 

 

 

HandHeld "HR-9" Duckie

Frequency:  144 - 148 MHz

SWR: Less than 1.5:1

Connector:  BNC Male

Length:   4 inches, or 105/mm

In Stock

9.95 HR-9 

 

 

 

 

 

 

 

 

HR-601VU
VHF & UHF Antenna

Dual-Band, HandHeld antenna, with SMA male connector for use with late model transceivers

 

 

 

In Stock

 

 

 

12.95  HR-601VU 

HR-601V is for VHF only handheld transceivers.

Frequency: 144-148 MHz
VSWR: Less than 1.8:1
Whip is Shape/Memory Alloy
Connector: SMA Male

 

In Stock

10.95  HR-601V

 

NMO Antenna Mount RAIN CAP.   
Used to cover the NMO mount when not in use.  Comes in basic gloss black.   
The NMO cover with built-in "0-Ring" seal.

 

In Stock                .99 ea, Order NMO5

 

HOLE PLUGS Drilled the hole in the wrong place? Removed an old base-loaded antenna;    This black hard-rubber plug is inserted into the hole to seal from moisture.  It can be painted to blend color. For easy insertion, and perfect seal, use RTV or similar sealer.   
  In Stock

The profile is about 1/8 inch high when inserted, 

Plug for 3/8" hole .99                Plug for 1/2" hole .99     

Plug for 5/8" hole .99                Plug for 3/4" hole .99     

Plug for 7/8" hole .99                Plug for   1" hole   .99   

This NMO Hole Mount will fit into a 3/8" hole, or use the adapter (included) to adapt it to a 3/4" hole.  The BUX CommCo NMOH is supplied with 17 ft of 98% shielded RG-58 cable terminated into a PL-259 UHF connector.  Cables are attached at right angles to the mount.  Mounts also include a built-in seal around the mounting hole to protect from moisture.    

 In Stock     AM-207B  $8.95

Trunk Lip, NMO Mount, model AM-209 is a trunk-lip mount supplied with 14 ft of RG-58 cable, a PL-259, and the industry standard NMO mount.  The AM-209 mounts on a standard trunk-lip and comes with 14ft of cable terminated in a PL-259.

In Stock     AM-209 $11.95  

NMO mount only.  For virgin installation when cable is already in place. No cable, only the NMO mount. Hardened Brass.

In Stock
$4.95 NMO-2  

 

 

ANTENNA ADAPTER
3/8"x24 thread base antenna to NMO Mount

When you don't care to drill another hole for that whip, or new antenna, this heavy-duty adapter mates a 3/8"x24 thread antenna base to an NMO mount.   Also includes "O" ring-to-body, seal to prevent moisture oxidation.

In Stock    NMO-6   $8.95   

NMO to SO239 Antenna Adapter
When you don't care to drill another hole for that whip, or new antenna, this heavy-duty adapter mates a SO-239 (PL259 type) antenna base to an NMO mount. Also includes "O" ring-to-body, seal to prevent moisture oxidation

.
$8.95 NMO8 

In Stock

 

Dual Band, 144-154 MHz & 440-460 MHz Trunk Lip Mount, Antenna
Trunk Lip Mount has steel lip clamp and dual set-screws.  With standard 3/8" X 24 thread base.  Pre-wired with 17" of RG-58 to BNC Connector.  Black rubber paint protector, see photo.  Includes  a PL-259  adapter/connector 

 

$14.95 DBTL270     

    

"The Adapter" is the best way to describe it !  Our number one seller when it comes to antenna adapters.

 $ 2.99 each  Cat#  7060   

BNC male to UHF Female  $2.99 ea

WINDOW CLIP for HT or SCANNER ANTENNA
SMA window antenna clip $10.95  AM 800 

BNC window antenna clip $11.95    AM 801B  

SMA or BNC "HAT" Clip-on Mount 
SMA $10.95,  AM 550  

 

BNC Hat Clip  $11.95  AM 551    

Your BUX BALUN is warranted against defects in components or construction for a period of three (3) months from date of purchase.  Our warranty does not cover damage due to misuse, abuse, or nonessential operation outside the  specifications of the BUX BALUN.  This warranty applies only to the original purchaser.  A copy of the receipt showing the purchaser’s name and the date of purchase must accompany BALUN's returned for warranty service or replacement.  All returns must be shipped prepaid.

Should there arise a requirement to return your BUX BALUN for service, carefully wrap and package it.   We will re-use your carton to return the BUX BALUN to you.  Be sure to include your return address.  Include a full description of the problem, along with your name, address, phone number and/or e-mail address.  Repairs average approximately 3 to 4 days.

QUAD MAGNET, Antenna Mount.
Available in; Triple Chrome Plate.  You asked for strength in a super mobile antenna mount, and WE DELIVERED !  Features 4,  five inch Heavy-Duty magnets, equally spaced on a Heavy Duty, 1/4" thick, hard-drawn metal frame.   The BUX4MM is prewired with 3/8" X 24 threaded (standard) Mount, and PL259 connector.  Accepts 3/8 X 24 antennas

 

$49.95  BUX4MMC  "chrome"

 

Six (6) ft RG-8U, High Quality, 50 Ohm impedance, Coax jumper.

These jumpers are made from high quality, lowloss, coax cable with PL259 connectors installed at each end.  

Ideal for transceiver to amplifier, Amplifier to antenna tuner and similar applications.

$ 6.95 each, Order code 8U6PLPL 

You've heard about it, and here it is; The GOLDEN Super "ROD" antenna Six section, telescoping  "rod" antenna for hand-held transceivers VSWR: Less than, 1.5:1   Connector:  BNC male

Length:   108cm extended (48") and 26.5cm collasped. approx.
 $12.95 

HR-22  $7.99 

Our "SDAB" UNUN (above)is an ideal companion for the VH-3200 Marine Antenna shown here.

VH3200 MARINE  ANTENNA
No Ground VHF Marine Antenna.Ideal for bass boats, small run-about, and sail boats.   3 dB gain effectively doubles your transmitter's  effective radiated power.  Great for auto's with fiberglass body's or for wood craft - no ground required.   Low profile 36" height is ideal for top mast mounts on sailboats or for use on bass and ski boats or run-a-bouts where long antennas might hamper operations. Comes complete with stainless steel "L" type mounting bracket and preassembled 15' coax cable fitted with PL259 connectors.
VH3200   $37.97

 

Trailer Hitch Mount, eight inches long, with 7/8" hole for mounting with trailer-hitch ball, bolt. for antennas with 3/8" X 24 (standard) antenna base. Stainless steel with SO239 coax fitting to receive PL259 coax connector.   Also accepts the BUX HF STIX shown above.
CAT#  THM1   $ 14.95  

NMO, Trailer Hitch Mount, Same as above, except has NMO mount for antennas with NMO antenna base.  Seventeen (17') feet of coaxial cable and PL259 connector.  Stainless steel bar with 7/8" hole for mounting with trailer-hitch ball bolt.   Includes NMO mount, 17 feet of coax with PL259 coax connector.  
  CAT# NMOTHM   $ 24.95  

3 inch, NMO Magnetic antenna mount. Black finish, and a good "grabber" to a smooth, flat, metal surface.  A good companion mount for the DB-2.  Black finish, and a good "grabber" to a smooth, flat, metal surface.  A good companion mount for the UV325 shown near top of this page.  

  

5 inch, NMO Magnetic antenna mount. Black finish,
and a good "grabber" to a smooth, flat, metal surface. A good companion mount for the DB-2 shown on this page.    This is a Larger, 5 inch heavy duty Magnet, w/coax and connector.  5 inch, NMO Magnetic antenna mount. Black finish, and a good "grabber" to a smooth, flat, metal surface.  A good companion mount for the UV325 shown near top of this page.  

   DB-2

Dual Band mobile antenna for 144 & 430 MHz   VSWR:  Less than, 1.5:1 Connector:  NMO base. Length: 39cm or 15.5 in. approx.   ADD the NMO, 5 inch magnet mount for a durable, dual-band mobile antenna combo
AM1043B  3.5 Inch, $14.95
  AM1045B   5 Inch  $17.95 
 		  DB2  $14.95
In Stock   In Stock   In Stock
   

Hi Quality Belden coax nine ft. jumper  made using top quality Amphenol connectors. 

  $6.97    ORDER No.  HIQ9JMPR 

 

AM-101. Magnetic SO239 Mount 3.5" strong magnet mount with black plastic finish. 17' RG58 coax with PL-259.

  
12.99     

 

 

 

Both, DB-2 and 1045B  for only: $29.95

$29.95  DB245


 

Great for Apartment Dwellers, RV, pickup truck-bed rail, or Bumper installations.  Rail or Bumper Heavy-Duty Antenna Mount

Length of this bar is 12 inches, and width is 2 inches.  The bar is almost one quarter inch thick.  Mounting screws and 3/8" X 24 standard thread, stud mount are included.    By using our KD-3 Kwik-Disconnect, you can quickly change bands, or make your antenna setup into a "stealth" installation

$14.95  order  BUXTRUXHD 

Shown here is our T-BAR TRUX Stake hole mount.  This one is for the serious HAM.  The T-Bar mount is constructed of stainless steel and locates the antenna directly over the truck bed rail.    Expandable rubber base locks mount for secure fit when tightened. Great for our HF stix and out heavy-duty whips.  Fits most pickup truck models and brands.  Heavy Duty Right angle SO239 and 3/8" x 24 threaded stud, included,

TSTAKMNT  $22.95

Right Angle SM1L Mount Right angle stud mount with  SO239 coaxial cable connector and a 3/8-24 threaded antenna socket. Great for those cramped areas.  Reg 11.95,  BUX COMM Price:  $8.88

  

Pick-Up Truck, Flat-BAR,
STAKE HOLE
Mount  w/SM1

  

Adjustable Bumper Mount with 3/8"x24 thread SM-1, and SO239 (PL259) input.  Both may be used on hatch-back lid-lip, trunk-lip, bumper & hood.

$ 6.95  each  

  $19.95    442 S   $16.95
  
In Stock   In Stock   In Stock

BUMPER MOUNT with SO239 input connector, accepts PL259.   $9.95 Order 422-S 		   
422S  $9.95    Ball Mount with SO-239 (female) connector,
  AM601S $11.95  		  

Ball Mount with terminal lug connection,
AM601L   $11.95 
In Stock   In Stock   In Stock
Heavy Duty Spring for Whips up to 102 inches.  

Often called the mobile antenna, Kwik-Disconnect
This Mobile Antenna Adapter... is a 'SNAP' to change antennas or bands in a matter of seconds

  


Set of five (5) Kwik-Connect Antenna adapters and snap-on stud. Make changing mobile antennas a 'SNAP!' with a set of 5 ''Kwik Disconnect'' adapters.
S55S  $8.95   KD3  $5.95    KD5 $15.95  Set of 5.
In Stock   In Stock   In Stock

Order Line ONLY, Mon > Fri 10 AM to 4 PM,  434 534 8873  or FAX your order, 24/7 to FAX 434 525 7818

 

The EZ230 enables you to fold your mobile antenna over to a low-profile, horizontal position. 

This prone position allows entry into low-overhead garages, and prevents damage to the antenna.  A "must" for the mobile HAM.

 Both sleeve and threaded section are standard
3/8" X 24 threads.

 
 

Dual Band whip antenna for 144 & 440 MHz   VSWR:  Less than, 1.5:1 Connector: 3/8" x 24 threads dual-band mobile antenna.
As shown,  antenna only, requires 3/8 X 24 base. 

Lost the ferrule that holds your whip-tip atop your BUX-STIX antenna?    Here is the replacement complete with set-screw.  Threads are standard 3/8 x 24. 
 
EZ230  $9.95  14440WP $3.97

TIPFERL $3.97

In Stock In Stock In Stock


50 Ohm impedance, 3 ft, 6 ft, 9 ft, 12 ft, & 18 feet.
These jumpers are made from high quality, low-loss, Belden coax cable with Amphenol PL-259 connectors installed.
Three ft. (3')    ORDER No.      8X3PLPL  $3.99    
Six ft. (6')         ORDER No.      8X6PLPL  $4.99     
Nine ft. (9')      ORDER No.      8X9PLPL  $5.99     
Twelve ft. (12')   ORDER No.  8X12PLPL  $7.99  
Eighteen ft. (18')ORDER No.  8X18PLPL  $8.99  

Fifty ft. (50')   ORDER No.                       RG8X50PLPL  $22.95  
One Hundred ft. (100') ORDER No. RG8X100PLPL  $34.95  

 Shop Online or call our Order Line Monday thru Friday (except holidays) 1-434-534-8873
Customer Service  [email protected]
 Download our Catalog As of December 10th our brand new Winter 04/05 catalog is available in PDF FORMAT

Bumper Mount includes (SM1) SO-239 UHF connector to 3/8x24 antenna base (see SM1, this page).  $7.95 ea 

Included→    AM370RS

Insulated Antenna Stud Mount with SO-239 female connector for easy connecting with
PL-259 fitting. Threaded for standard 3/8 X 24 mobile antenna use.

$ 2.99  SM1 

10 for 17.95

Mirror-Mount with insulated stud, for 3/8 X 24 thread medium duty mobile antenna mounting.

AM304S

$6.95  Each    

Replacement, Hardened, Nylon, Heavy duty,  Shoulder washer insulators, same as shoulder washers in SM1 Stud-Mount.

4 for 99¢ SM1SW

DVM 810
 PocketCraft 810B. Here's a digital multimeter (DVM).  Ideal for the Mountain-topper HAM Radio Operator, or technician.  It has an LCD 3.5 digit readout
Features found on more expensive meters are standard on this DMM, they include:
* A transistor and diode tester
* DC Amperes

* AC Amperes
* Overload protection
* 7 functions & 19 Ranges
* Includes 21" test leads and battery.
Ranges to: 1000 Volts DC, 750 Volts AC, 10 Amps DC, Resistance to 2,000,000 Ohms

Order DVM810

$ 9.95

 

Order Line ONLY, Mon > Fri 10 AM to 4 PM,  434 534 8873  or FAX your order, 24/7 to FAX 434 525 7818

F=1-5/8"

T=1"

S=1-1/8"

C=1/4"

W=5/32"

 5/32" X 1-5/8"

EYE = 1/4"

Eyebolt with nut, Machine Thread Zinc Plated

 Order EYEBOLT
39 cents each

Order EYEBOLTX3
3 for 99 cents

ANTENNA  INSULATORS

Weatherproof, (TENYTE) insulators.  Perfect for your DIPOLE or Windom antenna.
For the apartment dweller, you can now hang the 20 meter doublet
in the attic.   I've QSO'd with stations all over the world with the
33 ft dipole in my garage attic.   One insulator at the center, and one each end.  

It's great for other HF WINDOM and single-band dipole antennas.  Dielectric strength is comparable to the old ceramic insulators, without susceptibility to cracking or breakage under impact or extreme temperature changes.
 Package of  3,  $2.99   ANTINSL3              
 Package of 10, Insulators $8.99, ANTINSLX10

VHF-UHF DOUBLE FEMALE BULKHEAD (feed-thru) CONNECTORS

                
YES, we have "one"  1 inch long                     For bulkhead and through-the-wall UHF connector feed-thru connections, with nuts.:

Order 75181  (One  inch )          $ 1.79 ea.               10 for $15.50  
Order 75182  (Two inches)        $ 2.95 ea.             10 for $ 24.50  

Order 75183  (Three inches)     $ 3.69 ea.             10 for $ 32.50  
Order 75184  (Four inches)       $ 3.95 ea.             10 for $ 34.50  
Order 75186  (Six inches)          $ 4.95 ea.             10 for $ 44.50  
Order 75188  (Eight inches)     $ 8.95 ea.              10 for $ 82.50  
Order 751810 (Ten inches)       $ 10.95ea.            10 for $ 99.50   
Order 751812 (Twelve inches) $12.95ea.             10 for $ 114.50 

         

               Heavy Duty 1" Nuts for the above bulkhead connectors.
2/.99 cents HDM1NUT        HDM1NUTX10 10 for $ 3.99  


 


50 Ohm impedance, 3 ft, 6 ft, 9 ft, 12 ft, & 18 feet.
These jumpers are made from high quality, low-loss, Belden coax cable with Amphenol PL-259 connectors installed.
Three ft. (3')    ORDER No.      8X3PLPL  $3.99    
Six ft. (6')         ORDER No.      8X6PLPL  $4.99     
Nine ft. (9')      ORDER No.      8X9PLPL  $5.99     
Twelve ft. (12')   ORDER No.  8X12PLPL  $7.99  
Eighteen ft. (18')ORDER No.  8X18PLPL  $8.99  

Fifty ft. (50')   ORDER No.                       RG8X50PLPL  $22.95  
One Hundred ft. (100') ORDER No. RG8X100PLPL  $34.95  

Need a High Quality jumper from your transceiver to the linear?

A HiQuality coax jumper for that transceiver Output to linear input!

The connectors are Amphenol™  and coax is RG-8X by Belden.

Hi Quality, Six ft. jumper  made using high quality components. 

    $6.97    ORDER No.   HIQJMPR                                  

Reinforced, Double Bracket used with our "DBLSPCL" antennas shown elsewhere on this page.

Mount two mobile whips in a horizontal plane to form a compact apartment dweller Dipole,  or RV antenna.  Comes with mounting hardware and double Antenna Bracket as shown at left.
$14.95   DBLBRKT  
 

After a few years, the hardened, nylon shoulder washers become weather-brittle and break.  Keep a few spares in the Ham Shack:  
     4 for 99¢ SM1SW


Mobile tuneable-tip antennas.

BHF75M  75 METER  3/8" X 24 THREAD 8 feet long $16.95

BHF40M 40 METER  3/8" X 24 THREAD  8 feet long $16.95

BHF20M 20 METER 3/8" X 24 THREAD  8 feet long $16.95  

BHF17M 17 METER  3/8" X 24 THREAD 8 feet long $16.95 

BHF15M 15 METER 3/8" X 24 THREAD 8 feet long $16.95  

BHF10M 10 METER  3/8" X 24 THREAD 8 feet long $16.95 

BHF6M  6 METER  3/8" X 24 THREAD 5 feet long  $16.95   


Spare 48" Tips for above tuneable-tip antennas.TIP48, $2.95 

Here's the perfect solution for your RV and portable HF antenna applications.  Use our dipole, mast-mounted bracket for 'fixed-station', field-day operating, apartment dwellers, and the RV travelers.  With two of the mobile HF antennas shown at left, you can have the best of both worlds.

By combining a pair (two) of the single band HF Mobile (loaded) tuneable-tip antennas, and (VHF) whips at left, you can have an ideal, single element, horizontal dipole (beam). This type antenna opens the world of HF and VHF communications for the apartment dweller, RV HAM, field-day operating, and a variety of other uses and applications.  Antenna(s) Not Included.

$14.95 each
 DBLBRKT 
tuneable-tip antennas allow adjusting for minimum VSWR.  CLICK HERE to read more about our HF DIPOLE SPECIAL!

By combining a pair (two) of the single band HF Mobile (loaded) tuneable-tip antennas above, you can have an ideal, single element, horizontal dipole (beam). This type antenna opens the world of HF communications for the apartment dweller, RV HAM, field-day operating, and a variety of other uses and applications.  The packages described below include two antenna, the Double Antenna-Bracket (DBLBRKT), and mounting hardware

$ 39.97 DBLSPCL (without BALUN) With BALUN, see "DBLCOMBO", below.
75 Meters→,    40 Meters→,    20 Meters→,

17 Meters→,    15 Meters→,    10 Meters→,

 

 6 Meters →                       

RASCAL + CABLES TNC to Radio Cables RASCAL GLKits BASE ANTENNAS Mobile Antennas + RV/Portable Antennas RF Connectors, ETC Audio Connectors-CBLs BALUNS & UNUNs WINDOM & Antennas Power Cords-Connectors RASCAL CABLES WIRE & CABLE + Switches & Relays Meters, DVM & Panel Tools & Test Equip't Speakers & Mounts Fuses & Fuseholders NEW ADDITIONS RASCAL for EchoLink Replacement MICs J-Pole Handbook RASCAL Setup Manual RASCAL GLX on EchoLink Accessories & Solid State PSK31 for the Beginner HAM Antenna Primer PacketRadio Primer Packet Radio Glossary Volume Controls TNC to PC Comports Antenna Handbook Solving Hum & Noise Problems Loop Antenna Calculator IC-706 on EchoLink RASCAL CABLES CB Replacement MICs CB Mic Wiring Page 9600 Baud PhoenixSX Toroids & Ferrites Dealers Area All Products SOLAR Power for HAMs HAM Radio Freeware PConnector Index Building Packet Networks X1J4 Node Setup Packet SysOp Help Download BUXterm Free Radio Mods & More HAM Station Grounding Packet Node Code PacketRadio Band-plan Our Customer's say Mail Order Form Shipping & Returns HOME Zipped Catalog RASCAL 2006 CBLs Sale & Discount Items CommPartsCompany

BUX COMM PerfectWriter PEN  Has our name, address, and web page address and Toll Free number embossed on it.  Keep our web page address and toll free number  handy.

FREE with purchase of $ 50 or more.

Serving Telecommunications and HAM Radio since 1969
Call our toll-free OrderLine: 1 866 300 1969 Monday > Friday 9:AM to 4:PM,
Saturday, 1 800 726 2919, ORDERS ONLY  toll FREE  12 noon > 5 pm  eastern time

CLICK HERE to download RASCAL GLX to REPEATER interface Instructions via EchoLink

For Quantity Quotes or Dealer Pricing;

We accept:

 

Hit Counter

Shipping/Handling & warranty Return policy
   * "RASCAL"  is  Registered trademark ®™ of BUX Communications Corp (BUX CommCo ™) 
*(RASCAL™® "Radio And Sound Card Adapter Link")